Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2017.09–2018.04
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0333742 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB5  Open in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects an open in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB5 Open in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator


·

Outer mirror LH

·

Outer rear view mirror assembly with cover LH

·

Wire harness or connector

·

Blind spot monitor sensor LH

·

Outer mirror control ECU assembly LH



WIRING DIAGRAM

E372912E08
5.958,1.229 6.573,1.427 0.615,0.198 10 false OMIL 2.042,1.146 2.656,1.344 0.615,0.198 10 false BSL+ 2.292,1.646 2.448,1.844 0.156,0.198 10 false - 0.281,2.063 0.896,2.26 0.615,0.198 10 false IND2 0.271,2.219 2.365,3.083 2.094,0.865 10 false Outer Mirror LH 0.167,3.333 0.625,3.531 0.458,0.198 10 false O16 0.167,3.5 7.042,3.698 6.875,0.198 10 false Outer Rear View Mirror Assembly With Cover LH 5.823,3.365 6.135,3.563 0.313,0.198 10 false W6 5.823,3.5 7,4.385 1.177,0.885 10 false Blind Spot Monitor Sensor LH 5.781,1.146 5.938,1.344 0.156,0.198 10 false 4 2.51,1.125 2.667,1.323 0.156,0.198 10 false 3 2.49,1.635 2.802,1.833 0.313,0.198 10 false 11 3.271,1.552 3.583,1.75 0.313,0.198 10 false 12 3.604,1.74 4.063,1.938 0.458,0.198 10 false HTR- 4.927,1.552 5.083,1.75 0.156,0.198 10 false 7 2.958,2.146 5.625,2.385 2.667,0.24 10 false Outer Mirror Control ECU Assembly LH 1.385,1.219 1.542,1.417 0.156,0.198 10 false + 1.396,1.719 1.552,1.917 0.156,0.198 10 false - 1.604,1.125 1.76,1.323 0.156,0.198 10 false 2 1.604,1.615 1.76,1.813 0.156,0.198 10 false 1 0.26,2.385 2.292,3.031 2.031,0.646 10 false (Outer Rear View Mirror Indicator LH) 4.417,1.74 4.875,1.938 0.458,0.198 10 false GND 4.875,1.729 5.292,1.938 0.417,0.208 10 false O8 3.26,1.729 3.677,1.938 0.417,0.208 10 false O9


CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Turn the power switch on (IG).


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH - BLIND SPOT MONITOR SENSOR LH)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the W6 blind spot monitor sensor LH connector.


b.

Disconnect the O16 outer rear view mirror assembly with cover LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W6-4 (OMIL) - O16-3 (BSL+) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH AND BODY GROUND)
a.

Disconnect the O16 outer rear view mirror assembly with cover LH connector.


b.

Disconnect the O8 and O9 outer mirror control ECU assembly LH connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O16-11 (-) - O9-12 (HTR-) Always Below 1 Ω
O8-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH
a.

Disconnect the O8 and O9 outer mirror control ECU assembly LH connectors.


b.
E380797C02
0.833,0.281 1.25,0.542 0.417,0.26 2.167,0.271 2.583,0.531 0.417,0.26 1.052,1.688 1.156,1.229 false 2.125,1.688 2.01,1.094 false 0.948,0.323 1.406,0.521 0.458,0.198 10 false O9 2.281,0.323 2.74,0.521 0.458,0.198 10 false O8 0.135,0.104 0.594,0.302 0.458,0.198 10 false *a 0.896,1.729 1.354,1.927 0.458,0.198 10 false HTR- 2.031,1.74 2.49,1.938 0.458,0.198 10 false GND
*a Component without harness connected
(Outer Mirror Control ECU Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O8-7 (GND) - O9-12 (HTR-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

5.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH
a.

Disconnect the IND2 outer mirror LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O16-3 (BSL+) - IND2-2 (+) Always Below 1 Ω
O16-11 (-) - IND2-1 (-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT OUTER MIRROR LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH

6.INSPECT OUTER MIRROR LH

b.

Inspect the outer rear view mirror indicator LH on the outer mirror LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

NG