Home › Suspension › FRONT SUSPENSION › FRONT STABILIZER BAR › 2017.09–2019.02
RM33C0E _53 Suspension _065438 FRONT SUSPENSION _0334231 FRONT STABILIZER BAR A

FRONT SUSPENSION  FRONT STABILIZER BAR  INSTALLATION  


PROCEDURE

Hide 48815 1.INSTALL FRONT NO. 1 STABILIZER BAR BUSHING (for LH Side)

a.
C373252C01
0.677,0.417 0.781,0.417 0.781,0.417 1.115,0.917 false 2.219,1.156 2.76,1.656 2.76,1.656 2.844,1.656 true 2.885,1.573 3.198,1.729 0.313,0.156 10 false *a 0.51,0.333 0.823,0.49 0.313,0.156 10 false *b
*a Cutout
*b Stopper Ring
V100135

Front of the Vehicle
V100136

Outside of the Vehicle


Install the front No. 1 stabilizer bar bushing to the front stabilizer bar as shown in the illustration.

NOTICE:
·

Install the front No. 1 stabilizer bar bushing so that the cutout is facing the rear of the vehicle.

·

Install the front No. 1 stabilizer bar bushing onto the front stabilizer bar so that the stopper ring of the front stabilizer bar faces the outside of the vehicle.




Hide 48815 2.INSTALL FRONT NO. 1 STABILIZER BAR BUSHING (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 48811 3.INSTALL FRONT STABILIZER BAR

a.

Install the front stabilizer bar with the 2 front stabilizer bar bushings to the front frame assembly.

NOTICE:

Make sure that the identification mark is positioned as shown in the illustration.


C373255C01
2.844,2.156 2.844,2.51 2.844,2.51 3.188,2.51 false 3.229,2.427 3.542,2.583 0.313,0.156 10 false *a
*a Identification Mark - -
V100135

Front of the Vehicle - -



Hide 48829A 4.INSTALL FRONT NO. 1 STABILIZER BRACKET LH

a.
C373256C01
2.042,0.729 2.156,0.24 2.156,0.24 2.25,0.24 true 2.292,0.146 2.604,0.302 0.313,0.156 10 false *a 1,2.042 1.146,2.219 0.146,0.177 10 true A 2.25,2.24 2.396,2.417 0.146,0.177 10 true B
*a Arrow
V100136

Front of the Vehicle


Install the front No. 1 stabilizer bracket LH to the front frame assembly with the 2 bolts.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:
·

Make sure to install the front No. 1 stabilizer bracket LH with its arrow facing the front of the vehicle.

·

Temporarily tighten the bolt (B) and then fully tighten the 2 bolts in the order of (A) and (B).




Hide 48824A 5.INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 6.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

a.

Install the front stabilizer link assembly LH to the front stabilizer bar with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48820B 7.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.