1.INSTALL BOLT
Install the 2 bolts to the front frame assembly.
2.INSTALL HOLE PLUG
Install the 7 hole plugs to the front frame assembly.
There are 2 different shapes of hole plug.
52217E
3.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH
| *a | View from Underneath |
|
Front of the Vehicle |
Align a new front suspension member body mounting rear cushion LH as shown in the illustration and set it to the front frame assembly.
Position the front suspension member body mounting rear cushion LH in the correct direction.
Do not apply lubricant to the outer sleeve of the front suspension member body mounting rear cushion LH.
| *1 | Front Suspension Member Body Mounting Rear Cushion LH |
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
| *a | Hold |
|
Turn |
Using SST, install the front suspension member body mounting rear cushion LH as shown in the illustration.
Check that there is no clearance between the front frame assembly and the front suspension member body mounting rear cushion LH.
52215
4.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION
| *a | View from Underneath |
|
Front of the Vehicle |
Align a new front suspension member body mounting rear cushion as shown in the illustration and set it to the front frame assembly.
Position the front suspension member body mounting rear cushion in the correct direction.
Do not apply lubricant to the outer sleeve of the front suspension member body mounting rear cushion.
Install SST using the same procedure as for the front suspension member body mounting rear cushion LH.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
Using SST, install the front suspension member body mounting rear cushion.
Check that there is no clearance between the front frame assembly and the front suspension member body mounting rear cushion.
Perform the same procedure as for the front suspension member body mounting rear cushion LH.
52211J
5.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION (for LH Side)
| *a | View from Underneath |
|
Front of the Vehicle |
Align a new front suspension member body mounting front cushion as shown in the illustration and set it to the front frame assembly.
Position the front suspension member body mounting front cushion in the correct direction.
Do not apply lubricant to the outer sleeve of the front suspension member body mounting front cushion.
| *1 | Front Suspension Member Body Mounting Front Cushion |
Install SST as shown in the illustration.
Be sure to install SST (09830-01030) in the correct direction.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
| *a | Hold |
|
Turn |
Using SST, install the front suspension member body mounting front cushion as shown in the illustration.
Check that there is no clearance between the front frame assembly and the front suspension member body mounting front cushion.
52211J
6.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION (for RH Side)
| *a | View from Underneath |
|
Front of the Vehicle |
Align a new front suspension member body mounting front cushion as shown in the illustration and set it to the front frame assembly.
Position the front suspension member body mounting front cushion in the correct direction.
Do not apply lubricant to the outer sleeve of the front suspension member body mounting front cushion.
Install SST using the same procedure as for the LH side.
Be sure to install SST (09830-01030) in the correct direction.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
Using SST, install the front suspension member body mounting front cushion.
Check that there is no clearance between the front frame assembly and the front suspension member body mounting front cushion.
Perform the same procedure as for the LH side.
52216B
7.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER
Install the 2 front suspension member body mounting rear stoppers to the front frame assembly.
52213A
8.INSTALL FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER
Install the 2 front suspension member body mounting front stoppers to the front frame assembly.
17572B
9.INSTALL NO. 2 EXHAUST PIPE SUPPORT BRACKET
Install the No. 2 exhaust pipe support bracket to the front frame assembly with the 2 bolts.
48069
10.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly LH.
Install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
48068
11.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
44250
12.INSTALL RACK AND PINION POWER STEERING GEAR ASSEMBLY
13.INSTALL FRONT STABILIZER BAR WITH BRACKET
14.INSTALL FRONT FRAME ASSEMBLY
Install the rear engine mounting insulator to the front frame assembly with the 4 nuts.
Install the front engine mounting insulator to the front frame assembly with the 3 nuts.
15.CONNECT WIRE HARNESS
for LHD: Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR>INSTALLATION
for RHD: Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR>INSTALLATION
45319
16.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)
17.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE