Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM33C0E _58 Vehicle Interior _065456 THEFT DETERRENT / KEYLESS ENTRY _0330907 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn assembly to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B492645E02
0.792,0.135 2.938,0.333 2.146,0.198 10 false from Auxiliary Battery 0.438,1.073 1.688,1.271 1.25,0.198 10 false S-HORN 2.219,1.865 3.469,2.063 1.25,0.198 10 false S-HORN 1.604,2.26 4.229,2.563 2.625,0.302 10 false No. 5 Relay Block Assembly 4.375,1.625 5.979,2.385 1.604,0.76 10 false Instrument Panel Junction Block Assembly 4.146,3.74 4.635,3.958 0.49,0.219 10 false A14 4.146,3.896 6.25,4.219 2.104,0.323 10 false Security Horn Assembly 5.979,3.188 6.469,3.406 0.49,0.219 10 false MB 5.979,3.354 6.99,4.208 1.01,0.854 10 false Main Body ECU (Multiplex Network Body ECU) 4.375,1.469 4.865,1.688 0.49,0.219 10 false 3A 4.656,0.833 5.146,1.052 0.49,0.219 10 false 20 5.802,0.823 6.292,1.042 0.49,0.219 10 false 29 6.031,0.823 6.521,1.042 0.49,0.219 10 false SH 6.615,1.094 6.865,1.333 0.25,0.24 10 false IC 1.969,0.823 2.302,1.031 0.333,0.208 10 false 1 1.979,1.438 2.313,1.646 0.333,0.208 10 false 5 2.875,0.802 3.208,1.01 0.333,0.208 10 false 2 2.875,1.438 3.208,1.646 0.333,0.208 10 false 3 3.792,3.615 4.125,3.823 0.333,0.208 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY HORN)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Horn Security horn Assembly OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Security Horn
50004 123 20
OK:

The security horn assembly sounds and stops correctly when operated through the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT SECURITY HORN ASSEMBLY
2.INSPECT SECURITY HORN ASSEMBLY


Result:
Proceed to
OK
NG



OK

3.INSPECT S-HORN RELAY

NG

3.INSPECT S-HORN RELAY
a.
B256934C02
2.198,0.917 2.198,0.5 2.198,0.5 2.031,0.5 true 2.031,1.885 2.198,1.885 2.198,1.885 2.198,1.469 true 2.646,1.885 2.479,1.885 2.479,1.885 2.479,1.365 true 2.823,1 2.823,0.5 2.823,0.5 2.656,0.5 true 0.104,0.083 0.417,0.396 0.313,0.313 10 false *1 0.323,1.458 0.573,1.75 0.25,0.292 10 false 5 1.313,0.667 1.594,0.917 0.281,0.25 10 false 2 0.313,0.667 0.51,0.906 0.198,0.24 10 false 1 1.313,1.469 1.563,1.708 0.25,0.24 10 false 3 2.708,1.792 2.927,2.01 0.219,0.219 10 false 5 1.833,1.771 2.063,2 0.229,0.229 10 false 1 1.917,0.417 2.208,0.688 0.292,0.271 10 false 2 2.542,0.417 2.813,0.708 0.271,0.292 10 false 3
*1 S-HORN Relay


Remove the S-HORN relay from the No. 5 relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE S-HORN RELAY

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B472424C01
3.271,0.188 3.792,0.479 0.521,0.292 3.344,1.563 3.865,1.854 0.521,0.292 5.865,2.646 5.646,2.646 5.646,2.646 5.646,2.313 false 3.438,0.24 3.75,0.438 0.313,0.198 10 false 3A 3.49,1.625 3.802,1.823 0.313,0.198 10 false MB 5.906,2.552 6.438,2.75 0.531,0.198 10 false SH 0.208,0.146 0.521,0.344 0.313,0.198 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 3A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-20 - MB-29 (SH) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - S-HORN RELAY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - S-HORN RELAY)
a.
B340809C03
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 No. 5 Relay Block


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 5 relay block S-HORN relay terminal 1 - Body ground Power switch off 11 to 14 V
No. 5 relay block S-HORN relay terminal 5 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)
a.
B340809C03
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 No. 5 Relay Block


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 5 relay block S-HORN relay terminal 3 - A14-1 Always Below 1 Ω
No. 5 relay block S-HORN relay terminal 3 or A14-1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.
B340809C03
0.146,0.125 0.458,0.281 0.313,0.156 10 false *1
*1 No. 5 Relay Block


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 5 relay block S-HORN relay terminal 2 - 3A-20 Always Below 1 Ω
No. 5 relay block S-HORN relay terminal 2 or 3A-20 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR