Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light) › 2017.12–2018.04
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0341614 HEADLIGHT ASSEMBLY(for Bulb Type Turn Signal Light) G

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Bulb Type Turn Signal Light)  INSPECTION  


PROCEDURE

Hide 81175 1.INSPECT HEADLIGHT UNIT ASSEMBLY LH

E380640C01
1.104,5.167 1.469,5.385 0.365,0.219 3.469,5.448 3.833,5.667 0.365,0.219 5.813,5.479 6.177,5.698 0.365,0.219 0.948,7.219 1.313,7.438 0.365,0.219 2.74,7.229 3.104,7.448 0.365,0.219 4.51,7.24 4.875,7.458 0.365,0.219 6.063,7.219 6.427,7.438 0.365,0.219 0.333,6.115 0.688,6.313 false 1.865,6.292 2.208,6.063 false 0.5,5.896 0.958,6.292 false 0.719,5.688 1.094,6.281 false 1.188,5.677 1.344,6.302 false 1.521,5.677 1.458,6.302 false 1.917,5.781 1.583,6.302 false 0.396,6.594 0.74,6.458 false 0.646,6.771 1.104,6.469 false 0.927,6.885 1.229,6.469 false 1.448,6.885 1.458,6.469 false 1.813,6.854 1.719,6.469 false 2.156,6.688 1.833,6.479 false 0.313,0.104 0.625,0.302 0.313,0.198 10 false *1 2.469,4.365 2.781,4.563 0.313,0.198 10 false *a 5.844,2.406 6.156,2.604 0.313,0.198 10 false *b 5.781,1.917 6.094,2.115 0.313,0.198 10 false *b 5.542,1.292 5.854,1.49 0.313,0.198 10 false *b 5.271,0.802 5.583,1 0.313,0.198 10 false *c 1.052,1.771 1.365,1.969 0.313,0.198 10 false *d 1.688,1.031 2,1.229 0.313,0.198 10 false *d 1.323,0.135 1.635,0.333 0.313,0.198 10 false *e 0.427,5.198 0.74,5.396 0.313,0.198 10 false *a 1.24,5.198 1.552,5.396 0.313,0.198 10 false B 3.594,5.458 3.906,5.656 0.313,0.198 10 false G 5.948,5.51 6.26,5.708 0.313,0.198 10 false H 1.083,7.25 1.396,7.448 0.313,0.198 10 false F 2.875,7.26 3.188,7.458 0.313,0.198 10 false D 4.635,7.271 4.948,7.469 0.313,0.198 10 false C 6.188,7.25 6.5,7.448 0.313,0.198 10 false E 2.625,5.427 2.938,5.625 0.313,0.198 10 false *d 5.208,5.448 5.521,5.646 0.313,0.198 10 false *d 0.51,7.188 0.823,7.385 0.313,0.198 10 false *c 2.313,7.208 2.625,7.406 0.313,0.198 10 false *b 4.198,7.229 4.51,7.427 0.313,0.198 10 false *b 5.781,7.24 6.094,7.438 0.313,0.198 10 false *b 0.135,5.99 0.438,6.25 0.302,0.26 10 false HI- 2.24,5.938 2.542,6.198 0.302,0.26 10 false HI+ 0.052,5.688 0.625,5.917 0.573,0.229 10 false LOLED0 0.406,5.479 1,5.708 0.594,0.229 10 false LOLED2 0.99,5.458 1.583,5.688 0.594,0.229 10 false FANB 1.417,5.5 2.01,5.729 0.594,0.229 10 false ACTBI 1.875,5.604 2.469,5.833 0.594,0.229 10 false ACTSI 0.031,6.552 0.427,6.781 0.396,0.229 10 false DRL- 0.271,6.781 0.729,6.99 0.458,0.208 10 false FANG 0.708,6.917 1.167,7.125 0.458,0.208 10 false FANP 1.229,6.917 1.74,7.115 0.51,0.198 10 false ACTGI 1.729,6.906 2.24,7.104 0.51,0.198 10 false CLL+ 2.104,6.708 2.615,6.906 0.51,0.198 10 false DRL+
*1 Headlight Unit Assembly LH (Headlight Cord) - -
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight LED Unit Assembly LH)
*c Component without harness connected
(to Headlight Leveling Motor LH)
*d Component without harness connected
(to No. 1 Headlight Clearance LED Unit LH)
*e Component without turn signal light installed
(to Turn Signal Light)
- -


a.

Measure the resistance according to the value(s) in the table below.

i.

Inspect the headlight leveling motor circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-7 (ACTBI) - F-1 Always Below 1 Ω
B-8 (ACTSI) - F-2 Always Below 1 Ω
B-17 (ACTGI) - F-3 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


ii.

Inspect the Lo/Hi beam circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-4 (LOLED2) - C-2 Always Below 1 Ω
B-3 (LOLED0) - C-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


iii.

Inspect the Lo/Hi beam shade circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-10 (HI+) - E-1 Always Below 1 Ω
B-1 (HI-) - E-2 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


iv.

Inspect the headlight fan circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-6 (FANB) - D-3 Always Below 1 Ω
B-15 (FANP) - D-2 Always Below 1 Ω
B-14 (FANG) - D-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


v.

Inspect the clearance light/daytime running light input circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-20 (DRL+) - G-1 Always Below 1 Ω
B-11 (DRL-) - G-3 Always Below 1 Ω
B-19 (CLL+) - G-2 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


vi.

Inspect the clearance light/daytime running light output circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
G-4 - H-5 Always Below 1 Ω
G-5 - H-4 Always Below 1 Ω
G-6 - H-3 Always Below 1 Ω
G-7 - H-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).



Hide 81160A 2.INSPECT HEADLIGHT LED UNIT ASSEMBLY LH

E380641C01
0.583,0.438 0.896,0.635 0.313,0.198 10 false *a
*a Component without harness connected
(Headlight LED Unit Assembly LH)


a.

Apply auxiliary battery voltage to the headlight LED unit assembly LH and check that the Lo/Hi beam shade operates.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → Terminal 1
Auxiliary battery negative (-) → Terminal 2
Operates normally


If the result is not as specified, replace the headlight LED unit assembly LH.


Hide 8116A 3.INSPECT NO. 1 HEADLIGHT CLEARANCE LED UNIT LH

E380642C01
0.583,0.469 0.896,0.667 0.313,0.198 10 false *a
*a Component without harness connected
(No. 1 Headlight Clearance LED Unit LH)


a.

Apply auxiliary battery voltage to the No. 1 headlight clearance LED unit LH and check that the light illuminates.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → Terminal 1
Auxiliary battery negative (-) → Terminal 3
Clearance light/daytime running light illuminates


If the result is not as specified, replace the No. 1 headlight clearance LED unit LH.


Hide 81135 4.INSPECT HEADLIGHT UNIT ASSEMBLY RH

E380640C01
1.104,5.167 1.469,5.385 0.365,0.219 3.469,5.448 3.833,5.667 0.365,0.219 5.813,5.479 6.177,5.698 0.365,0.219 0.948,7.219 1.313,7.438 0.365,0.219 2.74,7.229 3.104,7.448 0.365,0.219 4.51,7.24 4.875,7.458 0.365,0.219 6.063,7.219 6.427,7.438 0.365,0.219 0.333,6.115 0.688,6.313 false 1.865,6.292 2.208,6.063 false 0.5,5.896 0.958,6.292 false 0.719,5.688 1.094,6.281 false 1.188,5.677 1.344,6.302 false 1.521,5.677 1.458,6.302 false 1.917,5.781 1.583,6.302 false 0.396,6.594 0.74,6.458 false 0.646,6.771 1.104,6.469 false 0.927,6.885 1.229,6.469 false 1.448,6.885 1.458,6.469 false 1.813,6.854 1.719,6.469 false 2.156,6.688 1.833,6.479 false 0.313,0.104 0.625,0.302 0.313,0.198 10 false *1 2.469,4.365 2.781,4.563 0.313,0.198 10 false *a 5.844,2.406 6.156,2.604 0.313,0.198 10 false *b 5.781,1.917 6.094,2.115 0.313,0.198 10 false *b 5.542,1.292 5.854,1.49 0.313,0.198 10 false *b 5.271,0.802 5.583,1 0.313,0.198 10 false *c 1.052,1.771 1.365,1.969 0.313,0.198 10 false *d 1.688,1.031 2,1.229 0.313,0.198 10 false *d 1.323,0.135 1.635,0.333 0.313,0.198 10 false *e 0.427,5.198 0.74,5.396 0.313,0.198 10 false *a 1.24,5.198 1.552,5.396 0.313,0.198 10 false B 3.594,5.458 3.906,5.656 0.313,0.198 10 false G 5.948,5.51 6.26,5.708 0.313,0.198 10 false H 1.083,7.25 1.396,7.448 0.313,0.198 10 false F 2.875,7.26 3.188,7.458 0.313,0.198 10 false D 4.635,7.271 4.948,7.469 0.313,0.198 10 false C 6.188,7.25 6.5,7.448 0.313,0.198 10 false E 2.625,5.427 2.938,5.625 0.313,0.198 10 false *d 5.208,5.448 5.521,5.646 0.313,0.198 10 false *d 0.51,7.188 0.823,7.385 0.313,0.198 10 false *c 2.313,7.208 2.625,7.406 0.313,0.198 10 false *b 4.198,7.229 4.51,7.427 0.313,0.198 10 false *b 5.781,7.24 6.094,7.438 0.313,0.198 10 false *b 0.135,5.99 0.438,6.25 0.302,0.26 10 false HI- 2.24,5.938 2.542,6.198 0.302,0.26 10 false HI+ 0.052,5.688 0.625,5.917 0.573,0.229 10 false LOLED0 0.406,5.479 1,5.708 0.594,0.229 10 false LOLED2 0.99,5.458 1.583,5.688 0.594,0.229 10 false FANB 1.417,5.5 2.01,5.729 0.594,0.229 10 false ACTBI 1.875,5.604 2.469,5.833 0.594,0.229 10 false ACTSI 0.031,6.552 0.427,6.781 0.396,0.229 10 false DRL- 0.271,6.781 0.729,6.99 0.458,0.208 10 false FANG 0.708,6.917 1.167,7.125 0.458,0.208 10 false FANP 1.229,6.917 1.74,7.115 0.51,0.198 10 false ACTGI 1.729,6.906 2.24,7.104 0.51,0.198 10 false CLL+ 2.104,6.708 2.615,6.906 0.51,0.198 10 false DRL+
*1 Headlight Unit Assembly RH (Headlight Cord) - -
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight LED Unit Assembly RH)
*c Component without harness connected
(to Headlight Leveling Motor RH)
*d Component without harness connected
(to No. 1 Headlight Clearance LED Unit RH)


a.

Measure the resistance according to the value(s) in the table below.

i.

Inspect the headlight leveling motor circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-7 (ACTBI) - F-1 Always Below 1 Ω
B-8 (ACTSI) - F-2 Always Below 1 Ω
B-17 (ACTGI) - F-3 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


ii.

Inspect the Lo/Hi beam circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-4 (LOLED2) - C-2 Always Below 1 Ω
B-3 (LOLED0) - C-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


iii.

Inspect the Lo/Hi beam shade circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-10 (HI+) - E-1 Always Below 1 Ω
B-1 (HI-) - E-2 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


iv.

Inspect the headlight fan circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-6 (FANB) - D-3 Always Below 1 Ω
B-15 (FANP) - D-2 Always Below 1 Ω
B-14 (FANG) - D-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


v.

Inspect the clearance light/daytime running light input circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-20 (DRL+) - G-1 Always Below 1 Ω
B-11 (DRL-) - G-3 Always Below 1 Ω
B-19 (CLL+) - G-2 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


vi.

Inspect the clearance light/daytime running light output circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
G-4 - H-5 Always Below 1 Ω
G-5 - H-4 Always Below 1 Ω
G-6 - H-3 Always Below 1 Ω
G-7 - H-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).



Hide 81140 5.INSPECT HEADLIGHT LED UNIT ASSEMBLY RH

E380641C01
0.583,0.438 0.896,0.635 0.313,0.198 10 false *a
*a Component without harness connected
(Headlight LED Unit Assembly RH)


a.

Apply auxiliary battery voltage to the headlight LED unit assembly RH and check that the Lo/Hi beam shade operates.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → Terminal 1
Auxiliary battery negative (-) → Terminal 2
Operates normally


If the result is not as specified, replace the headlight LED unit assembly RH.


Hide 8112A 6.INSPECT NO. 1 HEADLIGHT CLEARANCE LED UNIT RH

E380642C01
0.583,0.469 0.896,0.667 0.313,0.198 10 false *a
*a Component without harness connected
(No. 1 Headlight Clearance LED Unit RH)


a.

Apply auxiliary battery voltage to the No. 1 headlight clearance LED unit RH and check that the light illuminates.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → Terminal 1
Auxiliary battery negative (-) → Terminal 3
Clearance light/daytime running light illuminates


If the result is not as specified, replace the No. 1 headlight clearance LED unit RH.