Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/o Memory) › 2017.12–2021.02
RM33C0E _59 Vehicle Exterior _065470 MIRROR (EXT) _0332578 POWER MIRROR CONTROL SYSTEM(w/o Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/o Memory)  Mirror Heater does not Operate with Rear Defogger Switch  


DESCRIPTION

When the mirror heater switch (rear window defogger switch) on the radio and display receiver assembly*1 or air conditioning control assembly*2 is pressed, the operation signal is sent to the air conditioning amplifier assembly via CAN communication*1 or LIN communication*2. When the air conditioning amplifier assembly receives the signal, it turns on the DEF relay to operate the mirror heaters.

*1: for LHD

*2: for RHD


WIRING DIAGRAM

B473423E26
0.083,2.042 0.979,2.677 0.896,0.635 10 false from Auxiliary Battery 0.042,2.719 0.917,3.177 0.875,0.458 10 false from IG1-NO. 1 Relay 3.219,1.99 3.958,2.25 0.74,0.26 10 false MIR HTR 2.375,3.25 2.833,3.448 0.458,0.198 10 false DEF 4.99,3.417 6.01,3.708 1.021,0.292 10 false Outer Mirror RH 4.531,0.74 4.688,0.938 0.156,0.198 10 false + 6.302,0.75 6.458,0.948 0.156,0.198 10 false E 4.438,1.708 6.833,1.969 2.396,0.26 10 false Outer Rear View Mirror Assembly LH 4.385,3.958 6.781,4.198 2.396,0.24 10 false Outer Rear View Mirror Assembly RH 4.958,1.167 5.979,1.458 1.021,0.292 10 false Outer Mirror LH 4.542,3 4.698,3.198 0.156,0.198 10 false + 6.292,3 6.448,3.198 0.156,0.198 10 false E 0.917,7.219 3.031,7.667 2.115,0.448 10 false Rear Window Defogger Switch (Air Conditioning Control Assembly)*2 0.854,5.667 3.146,6.083 2.292,0.417 10 false Rear Window Defogger Switch (Radio and Display Receiver Assembly)*1 4.406,4.781 4.948,5.021 0.542,0.24 10 false RDFG 5.271,6.677 5.729,6.875 0.458,0.198 10 false GND 3.948,7.49 6.177,7.792 2.229,0.302 10 false Air Conditioning Amplifier Assembly 0.875,8.104 2.573,8.354 1.698,0.25 10 false : LIN Communication Line 0.885,8.479 2.719,8.729 1.833,0.25 10 false : CAN Communication Line 3.948,8.125 5.344,8.385 1.396,0.26 10 false *1: for LHD 3.948,8.479 5.344,8.74 1.396,0.26 10 false *2: for RHD 1.448,2.271 1.906,2.469 0.458,0.198 10 false DEF 2.99,1.708 3.208,1.927 0.219,0.219 10 false 3 1.927,2.01 2.146,2.229 0.219,0.219 10 false 5 1.917,1.406 2.135,1.625 0.219,0.219 10 false 4 1.927,2.615 2.146,2.833 0.219,0.219 10 false 2 3,2.604 3.219,2.823 0.219,0.219 10 false 1 4.344,0.74 4.698,0.958 0.354,0.219 10 false 2 4.365,3 4.76,3.229 0.396,0.229 10 false 2 6.51,0.75 6.792,0.979 0.281,0.229 10 false 11 6.531,3 6.813,3.229 0.281,0.229 10 false 11 4.781,3 5,3.219 0.219,0.219 10 false 1 4.781,0.74 5,0.958 0.219,0.219 10 false 1 6.063,0.75 6.281,0.969 0.219,0.219 10 false 2 6.073,3 6.292,3.219 0.219,0.219 10 false 2 4.208,4.656 4.427,4.875 0.219,0.219 10 false 5 5.677,6.552 5.896,6.771 0.219,0.219 10 false 4 4.438,1.552 5.51,1.823 1.073,0.271 10 false O16 4.396,3.802 5.385,4 0.99,0.198 10 false N19 3.958,7.333 4.76,7.594 0.802,0.26 10 false K54 1.063,2.865 2.104,3.208 1.042,0.344 10 false ECU-IG1 NO. 3

CAUTION / NOTICE / HINT

NOTICE:
·

The power mirror control system (w/o Memory) uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/o Memory) after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/o Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the auxiliary battery voltage is low, the mirror heater function may not operate. In this case, check the Data List item "Battery Control Count (Body ECU)".

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Defogger Relay (Rear) Mirror Heater OFF or ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Defogger Relay (Rear)
50004 121 22

Result:
Result Proceed to
Mirror heater operation on both mirrors is not normal A
Mirror heater operation on RH side mirror is not normal B
Mirror heater operation on LH side mirror is not normal C



A

2.CHECK WINDOW DEFOGGER SYSTEM

B

4.CHECK HARNESS AND CONNECTOR (DEF RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH - BODY GROUND)

C

6.CHECK HARNESS AND CONNECTOR (DEF RELAY - OUTER REAR VIEW MIRROR ASSEMBLY LH - BODY GROUND)
2.CHECK WINDOW DEFOGGER SYSTEM
a.

Check the window defogger system operation.

Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>OPERATION CHECK

OK:

The window defogger system operates normally.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DEF RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH/LH - BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (DEF RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH/LH - BODY GROUND)
a.

Remove the DEF relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the N19 outer rear view mirror assembly RH connector.


c.

Disconnect the O16 outer rear view mirror assembly LH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DEF relay holder terminal-3 - O16-2 (+) Always Below 1 Ω
DEF relay holder terminal-3 - N19-2 (+) Always Below 1 Ω
DEF relay holder terminal-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DEF RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH - BODY GROUND)
a.

Remove the DEF relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the N19 outer rear view mirror assembly RH connector.


c.

Disconnect the O16 outer rear view mirror assembly LH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DEF relay holder terminal-3 - N19-2 (+) Always Below 1 Ω
N19-11 (E) - Body ground Always Below 1 Ω
N19-2 (+) - Body ground Always 10 kΩ or higher
DEF relay holder terminal-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT OUTER MIRROR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT OUTER MIRROR RH

b.

Inspect the outer mirror RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION

OK:

Outer mirror RH is normal.



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

6.CHECK HARNESS AND CONNECTOR (DEF RELAY - OUTER REAR VIEW MIRROR ASSEMBLY LH - BODY GROUND)
a.

Remove the DEF relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Disconnect the O16 outer rear view mirror assembly LH connector.


c.

Disconnect the N19 outer rear view mirror assembly RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DEF relay holder terminal-3 - O16-2 (+) Always Below 1 Ω
O16-11 (E) - Body ground Always Below 1 Ω
O16-2 (+) - Body ground Always 10 kΩ or higher
DEF relay holder terminal-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT OUTER MIRROR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT OUTER MIRROR LH

b.

Inspect the outer mirror LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION

OK:

Outer mirror LH is normal.



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG