84870A
1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)
Check the mirror select switch and mirror surface adjust switch.
| *a | Mirror Select and Surface Adjust Switch |
| *b | Component without harness connected
(Outer Mirror Switch Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 15 (M+) - 12 (E) | Mirror surface adjust switch pushed up | 90 to 110 Ω |
| Mirror surface adjust switch pushed down | 437 to 503 Ω | |
| Mirror surface adjust switch pushed left | 744 to 856 Ω | |
| Mirror surface adjust switch pushed right | 225 to 275 Ω | |
| Mirror surface adjust switch not pushed | 10 kΩ or higher | |
| 13 (MSW) - 12 (E) | Mirror select switch turned to R position | Below 1 Ω |
| Mirror select switch turned to L position | 90 to 110 Ω | |
| Mirror select switch off | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Check that the LED illuminates.
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
| Auxiliary Battery Connection | Specified Condition |
|---|---|
| Auxiliary battery positive (+) - 14 (ILL+)
Auxiliary battery negative (-) - 16 (ILL-) |
LED illuminates |
If the result is not as specified, replace the outer mirror switch assembly.
84870A
2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Memory)
Check the mirror select switch and mirror surface adjust switch. (for LHD)
| *a | Mirror Select and Surface Adjust Switch |
| *b | Retractable Outer Mirror Switch |
| *c | Component without harness connected
(Outer Mirror Switch Assembly) |
Turn the mirror select switch to the L position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 10 (VL) - 7 (B)
13 (M+) - 5 (E) |
Up | Below 2 Ω |
| Off | 10 kΩ or higher | |
| 10 (VL) - 5 (E)
13 (M+) - 7 (B) |
Down | Below 2 Ω |
| Off | 10 kΩ or higher | |
| 9 (HL) - 7 (B)
13 (M+) - 5 (E) |
Left | Below 2 Ω |
| Off | 10 kΩ or higher | |
| 9 (HL) - 5 (E)
13 (M+) - 7 (B) |
Right | Below 2 Ω |
| Off | 10 kΩ or higher |
Turn the mirror select switch to the R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 12 (VR) - 7 (B)
13 (M+) - 5 (E) |
Up | Below 2 Ω |
| Off | 10 kΩ or higher | |
| 12 (VR) - 5 (E)
13 (M+) - 7 (B) |
Down | Below 2 Ω |
| Off | 10 kΩ or higher | |
| 11 (HR) - 7 (B)
13 (M+) - 5 (E) |
Left | Below 2 Ω |
| Off | 10 kΩ or higher | |
| 11 (HR) - 5 (E)
13 (M+) - 7 (B) |
Right | Below 2 Ω |
| Off | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Check the retractable outer mirror switch. (for LHD)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (MF) - 5 (E) | Extend position | 10 kΩ or higher |
| Except extend position | Below 1 Ω | |
| 6 (MR) - 5 (E) | Retract position | 10 kΩ or higher |
| Except retract position | Below 1 Ω |
If the result is not as specified, replace the outer mirror switch assembly.
Check that the LED illuminates. (for LHD)
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
| Auxiliary Battery Connection | Specified Condition |
|---|---|
| Auxiliary battery positive (+) - 8 (ILL+)
Auxiliary battery negative (-) - 14 (ILL-) |
LED illuminates |
If the result is not as specified, replace the outer mirror switch assembly.
Check the mirror select switch and mirror surface adjust switch. (for RHD, w/ Power Retract Mirror)
| *a | Mirror Select and Surface Adjust Switch |
| *b | Retractable Outer Mirror Switch |
| *c | Component without harness connected
(Outer Mirror Switch Assembly) |
Turn the mirror select switch to the L position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 12 (VL) - 15 (B)
9 (M+) - 1 (E) |
Up | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 12 (VL) - 1 (E)
9 (M+) - 15 (B) |
Down | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 13 (HL) - 15 (B)
9 (M+) - 1 (E) |
Left | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 13 (HL) - 1 (E)
9 (M+) - 15 (B) |
Right | Below 1 Ω |
| Off | 10 kΩ or higher |
Turn the mirror select switch to the R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 10 (VR) - 15 (B)
9 (M+) - 1 (E) |
Up | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 10 (VR) - 1 (E)
9 (M+) - 15 (B) |
Down | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 11 (HR) - 15 (B)
9 (M+) - 1 (E) |
Left | Below 1 Ω |
| Off | 10 kΩ or higher | |
| 11 (HR) - 1 (E)
9 (M+) - 15 (B) |
Right | Below 1 Ω |
| Off | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Check the retractable outer mirror switch. (for RHD, w/ Power Retract Mirror)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (MF) - 1 (E) | Extend position | 10 kΩ or higher |
| Except extend position | Below 1 Ω | |
| 16 (MR) - 1 (E) | Retract position | 10 kΩ or higher |
| Except retract position | Below 1 Ω |
If the result is not as specified, replace the outer mirror switch assembly.
Check the mirror select switch and mirror surface adjust switch. (for RHD, w/o Power Retract Mirror)
| *a | Mirror Select and Surface Adjust Switch |
| *b | Component without harness connected
(Outer Mirror Switch Assembly) |
Turn the mirror select switch to the L position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 12 (VL) - 15 (B)
9 (M+) - 7 (E) |
Up | Below 2 Ω |
| Off | 10 kΩ or higher | |
| 12 (VL) - 7 (E)
9 (M+) - 15 (B) |
Down | Below 2 Ω |
| Off | 10 kΩ or higher | |
| 13 (HL) - 15 (B)
9 (M+) - 7 (E) |
Left | Below 2 Ω |
| Off | 10 kΩ or higher | |
| 13 (HL) - 7 (E)
9 (M+) - 15 (B) |
Right | Below 2 Ω |
| Off | 10 kΩ or higher |
Turn the mirror select switch to the R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 10 (VR) - 15 (B)
9 (M+) - 7 (E) |
Up | Below 2 Ω |
| Off | 10 kΩ or higher | |
| 10 (VR) - 7 (E)
9 (M+) - 15 (B) |
Down | Below 2 Ω |
| Off | 10 kΩ or higher | |
| 11 (HR) - 15 (B)
9 (M+) - 7 (E) |
Left | Below 2 Ω |
| Off | 10 kΩ or higher | |
| 11 (HR) - 7 (E)
9 (M+) - 15 (B) |
Right | Below 2 Ω |
| Off | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Check that the LED illuminates. (for RHD)
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
| Auxiliary Battery Connection | Specified Condition |
|---|---|
| Auxiliary battery positive (+) - 14 (ILL+)
Auxiliary battery negative (-) - 8 (ILL-) |
LED illuminates |
If the result is not as specified, replace the outer mirror switch assembly.