Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat) › 2017.12–2018.04
RM33C0E _58 Vehicle Interior _065462 SEAT _0333603 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: w/ Occupant Classification System

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Occupant detection ECU

·

Front passenger seat*


Zero point calibration (Occupant classification system)
·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)

CAUTION:
·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



NOTICE:

If the front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for RHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the RH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 71910A 4.REMOVE FRONT SEAT HEADREST ASSEMBLY

a.

Remove the front seat headrest assembly from the front seat assembly.


Hide 72123A 5.REMOVE FRONT OUTER SEAT TRACK BRACKET COVER

a.

Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.


b.
B439770

Disengage the 2 claws to remove the front outer seat track bracket cover.


Hide 72123E 6.REMOVE FRONT INNER SEAT TRACK BRACKET COVER

a.
B439771

Disengage the 2 claws to remove the front inner seat track bracket cover.


Hide 72137T 7.REMOVE REAR OUTER SEAT TRACK BRACKET COVER

a.

Operate the seat track adjusting handle and move the front seat assembly to the foremost position.


b.
B439772

Disengage the 2 claws and guide to remove the rear outer seat track bracket cover.


Hide 72157F 8.REMOVE REAR INNER SEAT TRACK BRACKET COVER

a.
B439773

Disengage the 2 claws and guide to remove the rear inner seat track bracket cover.


Hide 9.REMOVE FRONT SEAT ASSEMBLY

a.
B429304

Using a T50 "TORX" socket wrench, remove the 2 bolts on the rear side of the front seat assembly.


b.

Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.


c.
B429303

Using a T50 "TORX" socket wrench, remove the 2 bolts on the front side of the front seat assembly.


d.

w/ Vertical Adjuster:

i.

Operate the vertical adjusting handle and move the front seat assembly to the uppermost position.



e.

Operate the seat track adjusting handle and move the front seat assembly to the center position.


f.

Operate the reclining adjuster release handle and move the seatback to the upright position.


g.

Disconnect the front seat airbag assembly connector under the front seat assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.
B474821C04
1.75,1.083 2.333,1.083 true 1.948,1.385 2.531,1.385 false 1.052,1.417 1.635,1.417 true 2.375,0.99 2.688,1.146 0.313,0.156 10 false *a 2.563,1.313 2.875,1.469 0.313,0.156 10 false *b 0.927,1.333 1.104,1.521 0.177,0.188 10 false A
*a White Housing Lock
*b Yellow CPA
V113147

Slide in this Direction


Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)


ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




h.

Disconnect each connector and disengage each clamp under the front seat assembly.


i.
B477724

Remove the front seat assembly.

NOTICE:

Be careful not to damage the vehicle body.