The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
Using this circuit, the radio and display receiver assembly sends power to the roof console box sub-assembly and telephone microphone assembly, and the roof console box sub-assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly and navigation ECU.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
A communication malfunction DTC may be stored.
The radio and display receiver assembly may not operate normally.
Enter the "Microphone Check" screen. Refer to Check Microphone (Input to navigation ECU) in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Check result is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Enter the "Microphone Check" screen. Refer to Check Microphone (Input to radio and display receiver assembly) in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Check result is normal.
| Result | Proceed to |
|---|---|
| NG (w/ Sliding Roof) | A |
| NG (w/o Sliding Roof) | B |
| OK | C |
A
B
C
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the V14 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-25 (SNS2) - V14-6 (SNS2) | Always | Below 1 Ω |
| K2-23 (MACC) - V14-9 (MACC) | Always | Below 1 Ω |
| K2-21 (MIN+) - V14-8 (MCO+) | Always | Below 1 Ω |
| K2-22 (MIN-) - V14-7 (MCO-) | Always | Below 1 Ω |
| K2-25 (SNS2) or V14-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| K2-23 (MACC) or V14-9 (MACC) - Body ground | Always | 10 kΩ or higher |
| K2-21 (MIN+) or V14-8 (MCO+) - Body ground | Always | 10 kΩ or higher |
| K2-22 (MIN-) or V14-7 (MCO-) - Body ground | Always | 10 kΩ or higher |
| K2-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K2 radio and display receiver assembly connector.
Connect the V14 roof console box sub-assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-23 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-24 (SGND) - Body ground | Always | Below 1 Ω |
| K2-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 (SNS2) - 7 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K2 radio and display receiver assembly connector.
Connect the V14 roof console box sub-assembly connector.
Turn the ignition switch to ACC.
| *a | Component with harness connected
(Roof Console Box Sub-assembly) |
Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the V14 roof console box sub-assembly connector.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | V14-8 (MCO+) - V14-7 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V14-8 (MCO+) - B-3 | Always | Below 1 Ω |
| V14-7 (MCO-) - B-2 | Always | Below 1 Ω |
| V14-8 (MCO+) or B-3 - V14-15 (GND) | Always | 10 kΩ or higher |
| V14-7 (MCO-) or B-2 - V14-15 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V14-6 (SNS2) - B-1 | Always | Below 1 Ω |
| V14-7 (MCO-) - B-2 | Always | Below 1 Ω |
| V14-6 (SNS2) or B-1 - V14-15 (GND) | Always | 10 kΩ or higher |
| V14-7 (MCO-) or B-2 - V14-15 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the V12 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-25 (SNS2) - V12-12 (SNS2) | Always | Below 1 Ω |
| K2-23 (MACC) - V12-9 (MACC) | Always | Below 1 Ω |
| K2-21 (MIN+) - V12-10 (MCO+) | Always | Below 1 Ω |
| K2-22 (MIN-) - V12-11 (MCO-) | Always | Below 1 Ω |
| K2-25 (SNS2) or V12-12 (SNS2) - Body ground | Always | 10 kΩ or higher |
| K2-23 (MACC) or V12-9 (MACC) - Body ground | Always | 10 kΩ or higher |
| K2-21 (MIN+) or V12-10 (MCO+) - Body ground | Always | 10 kΩ or higher |
| K2-22 (MIN-) or V12-11 (MCO-) - Body ground | Always | 10 kΩ or higher |
| K2-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K2 radio and display receiver assembly connector.
Connect the V12 roof console box sub-assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-23 (MACC) - Body ground | Ignition switch ACC. | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-24 (SGND) - Body ground | Always | Below 1 Ω |
| K2-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 12 (SNS2) - 11 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K2 radio and display receiver assembly connector.
Connect the V12 roof console box sub-assembly connector.
Turn the ignition switch to ACC.
| *a | Component with harness connected
(Roof Console Box Sub-assembly) |
Connect an oscilloscope to terminals 10 (MCO+) and 11 (MCO-) of the V12 roof console box sub-assembly connector.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | V12-10 (MCO+) - V12-11 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V12-10 (MCO+) - B-3 | Always | Below 1 Ω |
| V12-11 (MCO-) - B-2 | Always | Below 1 Ω |
| V12-10 (MCO+) or B-3 - V12-4 (GND) | Always | 10 kΩ or higher |
| V12-11 (MCO-) or B-2 - V12-4 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V12-12 (SNS2) - B-1 | Always | Below 1 Ω |
| V12-11 (MCO-) - B-2 | Always | Below 1 Ω |
| V12-12 (SNS2) or B-1 - V12-4 (GND) | Always | 10 kΩ or higher |
| V12-11 (MCO-) or B-2 - V12-4 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K1 radio and display receiver assembly connector.
Disconnect the K17 navigation ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K1-25 (MCO+) - K17-13 (MIC+) | Always | Below 1 Ω |
| K1-26 (MCO-) - K17-14 (MIC-) | Always | Below 1 Ω |
| K1-25 (MCO+) or K17-13 (MIC+) - Body ground | Always | 10 kΩ or higher |
| K1-26 (MCO-) or K17-14 (MIC-) - Body ground | Always | 10 kΩ or higher |
| K1-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K17 navigation ECU connector.
Turn the ignition switch to ACC.
| *a | Front view of wire harness connector
(to Navigation ECU) |
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | K17-13 (MIC+) - K17-14 (MIC-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG