These DTCs are stored when the low beam headlights do not illuminate, or a communication malfunction is detected between the light control ECU and main body ECU (multiplex network body ECU).
DTC B2430 or DTC B2431 may also be stored if a headlight cooling fan is malfunctioning. In this case, the light control ECU will dim or turn off the malfunctioning low beam headlight.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| B2430 | LED Headlight LH | Detection condition:
All of the following conditions are met: -
Power switch on (READY) -
Low beam headlights on Malfunction Status:
Any of the following conditions is met: -
Light control ECU malfunction -
Headlight LED unit assembly LH malfunction -
Light control ECU power source and signal malfunction Malfunction Time:
10 seconds or more |
·
Headlight LED unit assembly LH ·
Headlight unit assembly LH ·
Light control ECU ·
H-LP LH relay ·
Instrument panel junction block assembly ·
Main body ECU (multiplex network body ECU) ·
Harness or connector |
Main Body |
| B2431 | LED Headlight RH | Detection condition:
All of the following conditions are met: -
Power switch on (READY) -
Low beam headlights on Malfunction Status:
Any of the following conditions is met: -
Light control ECU malfunction -
Headlight LED unit assembly RH malfunction -
Light control ECU power source and signal malfunction Malfunction Time:
10 seconds or more |
·
Headlight LED unit assembly RH ·
Headlight unit assembly RH ·
Light control ECU ·
H-LP RH relay ·
Main body ECU (multiplex network body ECU) ·
Harness or connector |
Main Body |
HEADLIGHT ASSEMBLY CIRCUIT
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Check for DTCs.
DTC B2430 and B2431 are not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (DTC B2430 is output) | B |
| NG (DTC B2431 is output) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
| *a | Front view of wire harness connector
(to Headlight Assembly LH) |
Disconnect the A74 headlight assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A74-3 (LO) - Body ground | Light control switch in head position | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A74-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight Assembly LH) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A74-2 (S) - Body ground | Power switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Wire Harness) |
*b | Component without harness connected
(to Light Control ECU) |
| *c | Component without harness connected
(to Headlight LED Unit Assembly LH) |
- | - |
Remove the headlight assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>REMOVAL
Remove the headlight unit assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A74-1 (E) - B-6 | Always | Below 1 Ω |
| A74-2 (S) - B-12 | Always | Below 1 Ω |
| A74-3 (LO) - B-7 | Always | Below 1 Ω |
| B-4 - D-1 | Always | Below 1 Ω |
| B-10 - D-2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Remove each light control ECU, interchange the light control ECU (for LH) with (for RH) and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B2430 is output | A |
| DTC B2431 is output | B |
A
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
B
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Disconnect the K51 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A74-2 (S) - K51-14 (LLEW) | Always | Below 1 Ω |
| A74-2 (S) or K51-14 (LLEW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the H-LP LH relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (H-LP LH relay) - A74-3 (LO) | Always | Below 1 Ω |
| 3 (H-LP LH relay) or A74-3 (LO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the H-LP LH relay.
Click hereVehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (H-LP LH relay) - Body ground | Power switch off | 11 to 14 V |
| 5 (H-LP LH relay) - Body ground | Power switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (H-LP LH relay) - 3C-31 | Always | Below 1 Ω |
| 1 (H-LP LH relay) or 3C-31 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-31 - MB-15 (HRLY) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight Assembly RH) |
Disconnect the A73 headlight assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A73-3 (LO) - Body ground | Light control switch in head position | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A73-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight Assembly RH) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A73-2 (S) - Body ground | Power switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Wire Harness) |
*b | Component without harness connected
(to Light Control ECU) |
| *c | Component without harness connected
(to Headlight LED Unit Assembly RH) |
- | - |
Remove the headlight assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>REMOVAL
Remove the headlight unit assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A73-1 (E) - B-6 | Always | Below 1 Ω |
| A73-2 (S) - B-12 | Always | Below 1 Ω |
| A73-3 (LO) - B-7 | Always | Below 1 Ω |
| B-4 - D-1 | Always | Below 1 Ω |
| B-10 - D-2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Remove each light control ECU, interchange the light control ECU (for RH) with (for LH) and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B2431 is output | A |
| DTC B2430 is output | B |
A
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
B
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Disconnect the K51 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A73-2 (S) - K51-15 (RLEW) | Always | Below 1 Ω |
| A73-2 (S) or K51-15 (RLEW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the H-LP RH relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (H-LP RH relay) - A73-3 (LO) | Always | Below 1 Ω |
| 3 (H-LP RH relay) or A73-3 (LO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the H-LP RH relay.
Click hereVehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (H-LP RH relay) - Body ground | Power switch off | 11 to 14 V |
| 5 (H-LP RH relay) - Body ground | Power switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K52 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (H-LP RH relay) - K52-12 (HRY2) | Always | Below 1 Ω |
| 1 (H-LP RH relay) or K52-12 (HRY2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG