Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/o Automatic Headlight Beam Level Control System) › 2018.04–2021.02
RM33C0E _59 Vehicle Exterior _065472 LIGHTING (EXT) _0350992 LIGHTING SYSTEM(w/o Automatic Headlight Beam Level Control System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/o Automatic Headlight Beam Level Control System)  High Beam Headlight Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the high beam headlights.

WIRING DIAGRAM

E367355E14
6.177,1.042 6.635,1.24 0.458,0.198 10 false DIM 5.948,1.042 6.406,1.24 0.458,0.198 10 false 13 5.51,1.906 5.969,2.104 0.458,0.198 10 false K52 5.51,2.073 7.156,2.552 1.646,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 2.063,1.427 2.521,1.625 0.458,0.198 10 false DIM 0.625,1.042 1.302,1.24 0.677,0.198 10 false H-LP RH 0.719,0.417 2.156,0.646 1.438,0.229 10 false from Auxiliary Battery 1.823,0.792 2.031,1.031 0.208,0.24 10 false 5 1.823,1.083 2.031,1.323 0.208,0.24 10 false 2 2.479,0.802 2.688,1.042 0.208,0.24 10 false 3 2.479,1.083 2.688,1.323 0.208,0.24 10 false 1 1.406,2.781 2.375,3.01 0.969,0.229 10 false A74 1.396,2.917 3.302,3.271 1.906,0.354 10 false Headlight Assembly LH 1.385,4.229 3.313,4.531 1.927,0.302 10 false Headlight Assembly RH 1.385,4.094 3.073,4.375 1.688,0.281 10 false A73 2.344,2.292 2.729,2.531 0.385,0.24 10 false SOL 1.75,2.292 2.135,2.51 0.385,0.219 10 false E 1.75,3.615 2.104,3.844 0.354,0.229 10 false E 1.563,2.177 1.854,2.427 0.292,0.25 10 false 1 2.719,2.177 3.052,2.448 0.333,0.271 10 false 4 2.354,3.615 2.74,3.854 0.385,0.24 10 false SOL 2.729,3.51 3.063,3.781 0.333,0.271 10 false 4 1.552,3.49 1.844,3.74 0.292,0.25 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Check the operation of the low beam headlights. If the low beam headlights do not operate normally, refer to Problem Symptoms Table.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Automatic Headlight Beam Level Control System)>PROBLEM SYMPTOMS TABLE

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Head Light Hi High beam headlights OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Head Light Hi
50004 123 15
OK:

High beam headlights illuminate.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT DIM RELAY
2.INSPECT DIM RELAY

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - DIM RELAY)

NG

REPLACE DIM RELAY

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - DIM RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (DIM relay) - Body ground Power switch off 11 to 14 V
5 (DIM relay) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (DIM RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DIM RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K52 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (DIM relay) - K52-13 (DIM) Always Below 1 Ω
1 (DIM relay) or K52-13 (DIM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR