The main body ECU (multiplex network body ECU) controls the front fog lights.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Check the operation of the taillights.
Taillights operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Fog Light Relay | Front fog lights | OFF or ON | Light control switch in tail position |
| Tester Display |
|---|
| Front Fog Light Relay |
Front fog light relay operates. (Front fog lights come on.)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the FOG FR relay.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (FOG FR relay) - Body ground | Power switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (FOG FR relay) - Body ground | Light control switch in tail or head position | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the FOG FR relay.
Click hereVehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A57 fog light assembly LH connector.
Disconnect the A56 fog light assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (FOG FR relay) - A57-2 (B) | Always | Below 1 Ω |
| 3 (FOG FR relay) - A56-2 (B) | Always | Below 1 Ω |
| 3 (FOG FR relay) or A57-2 (B) - Body ground | Always | 10 kΩ or higher |
| 3 (FOG FR relay) or A56-2 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (FOG FR relay) - 3C-25 | Always | Below 1 Ω |
| 1 (FOG FR relay) or 3C-25 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-25 - MB-7 (FFGO) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (FOG FR relay) - 3C-32 | Always | Below 1 Ω |
| 2 (FOG FR relay) or 3C-32 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG