Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › from 2018.04
RM33C0E _58 Vehicle Interior _065462 SEAT _0333598 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)


E360013C01
0.938,0.333 1.313,0.573 0.375,0.24 1.625,0.333 2,0.573 0.375,0.24 2.365,0.333 2.74,0.573 0.375,0.24 3,0.333 3.375,0.573 0.375,0.24 4.625,0.313 5,0.552 0.375,0.24 5.302,0.313 5.677,0.552 0.375,0.24 5.385,0.354 5.698,0.552 0.313,0.198 10 false a31 3.073,0.365 3.385,0.563 0.313,0.198 10 false a30 1.698,0.365 2.01,0.563 0.313,0.198 10 false a29 1.333,0.344 1.646,0.542 0.313,0.198 12 false *A 1.021,0.375 1.479,0.573 0.458,0.198 10 false b10 2.031,0.344 2.344,0.542 0.313,0.198 12 false *B 3.406,0.344 3.719,0.542 0.313,0.198 12 false *B 2.76,0.354 3.073,0.552 0.313,0.198 12 false *A 2.438,0.365 2.896,0.563 0.458,0.198 10 false b11 4.698,0.344 5.156,0.542 0.458,0.198 10 false b22 5.031,0.313 5.344,0.51 0.313,0.198 12 false *A 5.719,0.323 6.031,0.521 0.313,0.198 12 false *B
*A for LHD *B for RHD


a.

for LHD

i.

Disconnect the b10 and b22 position control ECU assembly (driver seat) connectors.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
b10-2 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
b10-3 (+B) - Body ground W - Body ground Auxiliary battery power supply Power switch off 11 to 14 V
b22-1 (IG) - Body ground P - Body ground Ignition power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
b22-15 (SYSB) - Body ground G - Body ground System power source Power switch off 11 to 14 V


iii.

Reconnect the b10 and b22 position control ECU assembly (driver seat) connectors.


iv.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
b10-1 (SLD+) - Body ground L - Body ground Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
b10-5 (SLD-) - Body ground GR - Body ground Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
b10-6 (LFT+) - Body ground V - Body ground Rear lifter motor signal (upward) Rear lifter switch off Below 1 V
Rear lifter switch on (Upward) 11 to 14 V
b10-7 (FRV+) - Body ground B - Body ground Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
b10-9 (L+) - Body ground V - Body ground Lumbar support adjuster motor signal (forward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Forward) 11 to 14 V
b10-10 (RCL+) - Body ground P - Body ground Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
b11-3 (L-) - Body ground L - Body ground Lumbar support adjuster motor signal (rearward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Rearward) 11 to 14 V
b11-4 (FRV-) - Body ground R - Body ground Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
b11-5 (LFT-) - Body ground G - Body ground Lifter motor signal (downward) Rear lifter switch off Below 1 V
Rear lifter switch on (Downward) 11 to 14 V
b11-6 (RCL-) - Body ground LG - Body ground Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
b22-4 (LFLF) - Body ground W - Body ground Front power seat switch (driver seat) (lumbar support adjuster switch (forward)) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Forward) Below 1 V
b22-6 (FRVU) - Body ground L - Body ground Front power seat switch (driver seat) (front vertical switch (upward)) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Upward) Below 1 V
b22-7 (LFTU) - Body ground BR - Body ground Front power seat switch (driver seat) (rear lifter switch (upward)) signal Rear lifter switch off 11 to 14 V
Rear lifter switch on (Upward) Below 1 V
b22-8 (RCLF) - Body ground R - Body ground Front power seat switch (driver seat) (reclining switch (forward)) signal Reclining switch off 11 to 14 V
Reclining switch on (Forward) Below 1 V
b22-9 (SLDF) - Body ground B - Body ground Front power seat switch (driver seat) (slide switch (forward)) signal Slide switch off 11 to 14 V
Slide switch on (Forward) Below 1 V
b22-12 (SENG) - Body ground BR - Body ground Sensor ground Always Below 1 Ω
b22-18 (LFLR) - Body ground L - Body ground Front power seat switch (driver seat) (lumbar support adjuster switch (rearward)) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Rearward) Below 1 Ω
b22-20 (FRVD) - Body ground V - Body ground Front power seat switch (driver seat) (front vertical switch (downward)) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Downward) Below 1 V
b22-21 (LFTD) - Body ground LG - Body ground Front power seat switch (driver seat) (rear lifter switch (downward)) signal Rear lifter switch off 11 to 14 V
Rear lifter switch on (Downward) Below 1 V
b22-22 (RCLR) - Body ground G - Body ground Front power seat switch (driver seat) (reclining switch (rearward)) signal Reclining switch off 11 to 14 V
Reclining switch on (Rearward) Below 1 V
b22-23 (SLDR) - Body ground GR - Body ground Front power seat switch (driver seat) (slide switch (rearward)) signal Slide switch off 11 to 14 V
Slide switch on (Rearward) Below 1 V


v.

Check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
b22-10 (SSFV) - Body ground L - Body ground Front vertical position signal Front vertical function operating 4.8 to 5.1 V
b22-11 (SSRR) - Body ground V - Body ground Reclining position signal Reclining function operating 4.8 to 5.1 V
b22-25 (SSRL) - Body ground B - Body ground Rear lifter position signal Rear lifter function operating 4.8 to 5.1 V
b22-26 (SSRS) - Body ground G - Body ground Slide position signal Slide function operating 4.8 to 5.1 V



b.

for RHD

i.

Disconnect the a29 and a31 position control ECU assembly (driver seat) connectors.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
a29-2 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
a29-3 (+B) - Body ground W - Body ground Auxiliary battery power supply Power switch off 11 to 14 V
a31-1 (IG) - Body ground P - Body ground Ignition power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
a31-15 (SYSB) - Body ground G - Body ground System power source Power switch off 11 to 14 V


iii.

Reconnect the a29 and a31 position control ECU assembly (driver seat) connectors.


iv.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
a29-1 (SLD+) - Body ground L - Body ground Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
a29-5 (SLD-) - Body ground GR - Body ground Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
a29-6 (LFT+) - Body ground V - Body ground Rear lifter motor signal (upward) Rear lifter switch off Below 1 V
Rear lifter switch on (Upward) 11 to 14 V
a29-7 (FRV+) - Body ground B - Body ground Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
a29-9 (L+) - Body ground V - Body ground Lumbar support adjuster motor signal (forward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Forward) 11 to 14 V
a29-10 (RCL+) - Body ground P - Body ground Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
a30-3 (L-) - Body ground L - Body ground Lumbar support adjuster motor signal (rearward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Rearward) 11 to 14 V
a30-4 (FRV-) - Body ground R - Body ground Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
a30-5 (LFT-) - Body ground G - Body ground Lifter motor signal (downward) Rear lifter switch off Below 1 V
Rear lifter switch on (Downward) 11 to 14 V
a30-6 (RCL-) - Body ground LG - Body ground Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
a31-4 (LFLF) - Body ground W - Body ground Front power seat switch (driver seat) (lumbar support adjuster switch (forward)) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Forward) Below 1 V
a31-6 (FRVU) - Body ground L - Body ground Front power seat switch (driver seat) (front vertical switch (upward)) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Upward) Below 1 V
a31-7 (LFTU) - Body ground BR - Body ground Front power seat switch (driver seat) (rear lifter switch (upward)) signal Rear lifter switch off 11 to 14 V
Rear lifter switch on (Upward) Below 1 V
a31-8 (RCLF) - Body ground R - Body ground Front power seat switch (driver seat) (reclining switch (forward)) signal Reclining switch off 11 to 14 V
Reclining switch on (Forward) Below 1 V
a31-9 (SLDF) - Body ground B - Body ground Front power seat switch (driver seat) (slide switch (forward)) signal Slide switch off 11 to 14 V
Slide switch on (Forward) Below 1 V
a31-12 (SENG) - Body ground BR - Body ground Sensor ground Always Below 1 Ω
a31-18 (LFLR) - Body ground L - Body ground Front power seat switch (driver seat) (lumbar support adjuster switch (rearward)) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Rearward) Below 1 Ω
a31-20 (FRVD) - Body ground V - Body ground Front power seat switch (driver seat) (front vertical switch (downward)) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Downward) Below 1 V
a31-21 (LFTD) - Body ground LG - Body ground Front power seat switch (driver seat) (rear lifter switch (downward)) signal Rear lifter switch off 11 to 14 V
Rear lifter switch on (Downward) Below 1 V
a31-22 (RCLR) - Body ground G - Body ground Front power seat switch (driver seat) (reclining switch (rearward)) signal Reclining switch off 11 to 14 V
Reclining switch on (Rearward) Below 1 V
a31-23 (SLDR) - Body ground GR - Body ground Front power seat switch (driver seat) (slide switch (rearward)) signal Slide switch off 11 to 14 V
Slide switch on (Rearward) Below 1 V


v.

Check for pulses according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
a31-10 (SSFV) - Body ground L - Body ground Front vertical position signal Front vertical function operating 4.8 to 5.1 V
a31-11 (SSRR) - Body ground V - Body ground Reclining position signal Reclining function operating 4.8 to 5.1 V
a31-25 (SSRL) - Body ground B - Body ground Rear lifter position signal Rear lifter function operating 4.8 to 5.1 V
a31-26 (SSRS) - Body ground G - Body ground Slide position signal Slide function operating 4.8 to 5.1 V




CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)


B343031C31
3.979,0.083 4.396,0.333 0.417,0.25 1.76,0.083 2.177,0.333 0.417,0.25 2.563,0.083 2.979,0.333 0.417,0.25 4.74,0.083 5.156,0.333 0.417,0.25 4.854,0.115 5.365,0.333 0.51,0.219 10 false N9 2.646,0.125 3.156,0.344 0.51,0.219 10 false N10 3.01,0.104 3.323,0.302 0.313,0.198 12 false *B 1.885,0.115 2.198,0.313 0.313,0.198 10 false O9 2.219,0.104 2.531,0.302 0.313,0.198 12 false *A 5.188,0.104 5.5,0.302 0.313,0.198 12 false *B 4.438,0.104 4.75,0.302 0.313,0.198 12 false *A 4.104,0.115 4.417,0.313 0.313,0.198 10 false O8
*A for LHD *B for RHD


a.

for LHD

i.

Disconnect the O8 outer mirror control ECU assembly (driver door) connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
O8-6 (CPUB) - O8-7 (GND) LA-L - W-B Auxiliary battery power supply Power switch off 11 to 14 V
O8-14 (BDR) - O8-7 (GND) GR - W-B Auxiliary battery power supply Power switch off 11 to 14 V
O8-5 (SIG) - O8-7 (GND) LA-B - W-B Ignition power supply Power switch on (IG) 11 to 14 V
O8-5 (SIG) - O8-7 (GND) LA-B - W-B Ignition power supply Always Below 1 V
O8-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


iii.

Reconnect the O8 outer mirror control ECU assembly (driver door) connector.


iv.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
O8-1 (MM) - O8-7 (GND) GR - W-B SET switch signal for seat memory switch (driver door) SET switch on Below 1 V
SET switch off 11 to 14 V
O8-2 (M1) - O8-7 (GND) BR - W-B M1 switch signal for seat memory switch (driver door) M1 switch on Below 1 V
M1 switch off 11 to 14 V
O8-3 (M2) - O8-7 (GND) R - W-B M2 switch signal for seat memory switch (driver door) M2 switch on Below 1 V
M2 switch off 11 to 14 V



b.

for RHD

i.

Disconnect the N9 outer mirror control ECU assembly (driver door) connector.


ii.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
N9-6 (CPUB) - N9-7 (GND) LA-L - W-B Auxiliary battery power supply Power switch off 11 to 14 V
N9-14 (BDR) - N9-7 (GND) GR - W-B Auxiliary battery power supply Power switch off 11 to 14 V
N9-5 (SIG) - N9-7 (GND) LA-B - W-B Ignition power supply Power switch on (IG) 11 to 14 V
N9-5 (SIG) - N9-7 (GND) LA-B - W-B Ignition power supply Always Below 1 V
N9-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


iii.

Reconnect the N9 outer mirror control ECU assembly (driver door) connector.


iv.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
N9-1 (MM) - N9-7 (GND) GR - W-B SET switch signal for seat memory switch (driver door) SET switch on Below 1 V
SET switch off 11 to 14 V
N9-2 (M1) - N9-7 (GND) BR - W-B M1 switch signal for seat memory switch (driver door) M1 switch on Below 1 V
M1 switch off 11 to 14 V
N9-3 (M2) - N9-7 (GND) R - W-B M2 switch signal for seat memory switch (driver door) M2 switch on Below 1 V
M2 switch off 11 to 14 V




CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B472410C24
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 5.302,6.396 5.74,6.646 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.302,6.083 5.74,6.333 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 5.385,4.615 5.823,4.865 0.438,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 0.531,2.49 0.531,2.323 0.531,2.323 0.865,2.323 false 3.469,7.677 3.781,7.875 0.313,0.198 10 false MB 4.292,0.219 4.604,0.417 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false K51 2.052,1.479 2.365,1.677 0.313,0.198 10 false K52 2.052,1.802 2.365,2 0.313,0.198 10 false K53 0.875,1.073 1.188,1.271 0.313,0.198 10 false 3D 0.875,1.656 1.188,1.854 0.313,0.198 10 false 3C 0.885,2.021 1.198,2.219 0.313,0.198 10 false 3E 5.854,1.146 6.167,1.344 0.313,0.198 10 false 3B 5.854,1.76 6.167,1.958 0.313,0.198 10 false 3A 1.229,3.281 1.542,3.479 0.313,0.198 10 false K53 3.271,3.25 3.583,3.448 0.313,0.198 10 false K52 5.542,3.24 5.854,3.438 0.313,0.198 10 false K51 1.833,4.604 2.146,4.802 0.313,0.198 10 false 3A 1.24,6.198 1.552,6.396 0.313,0.198 10 false 3C 3.813,6.156 4.125,6.354 0.313,0.198 10 false 3D 5.427,6.115 5.74,6.313 0.313,0.198 10 false 3F 6.448,6.229 6.76,6.427 0.313,0.198 10 false 3E 5.521,4.646 5.833,4.844 0.313,0.198 10 false 3B 5.427,6.427 5.74,6.625 0.313,0.198 10 false 3G 5.813,6.104 6.125,6.302 0.313,0.198 12 false *A 5.823,6.406 6.135,6.604 0.313,0.198 12 false *B 0.365,2.531 0.76,2.76 0.396,0.229 10 false 3F 0.365,2.729 0.865,2.917 0.5,0.188 10 false 3G 0.521,2.521 0.917,2.75 0.396,0.229 12 false *A 0.552,2.708 1.052,2.896 0.5,0.188 12 false *B
*A for LHD *B for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-31 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply Power switch on (IG) 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply Power switch off Below 1 V
MB-30 (ACC) - Body ground - Ignition power supply Power switch on (ACC) 11 to 14 V
MB-30 (ACC) - Body ground - Ignition power supply Power switch off Below 1 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
K52-1 (FLCY) - Body ground W - Body ground Front door courtesy light switch assembly LH input Front door LH closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω
K52-6 (FRCY) - Body ground BE - Body ground Front door courtesy light switch assembly RH input Front door RH closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω