Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › from 2018.04
RM33C0E _58 Vehicle Interior _065462 SEAT _0333598 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2653  Lifter Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly (driver seat) does not receive a lifter motor position sensor signal despite the seat having been moved upward or downward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2653 Lifter Sensor Malfunction Lifter motor position sensor signal not received when power seat moved upward or downward
·

Position control ECU assembly (driver seat)

·

Power seat lifter motor assembly (driver seat)

·

Wire harness or connector



WIRING DIAGRAM

B510520E02
2.198,0.438 2.354,0.635 0.156,0.198 10 false 1 2.198,0.948 2.354,1.146 0.156,0.198 10 false 4 2.198,1.458 2.354,1.656 0.156,0.198 10 false 2 2.198,1.99 2.354,2.188 0.156,0.198 10 false 3 0.75,2.458 1.771,2.74 1.021,0.281 10 false b7*1, a36*2 0.75,2.625 2.844,3.24 2.094,0.615 10 false Power Seat Lifter Motor Assembly (Driver Seat) 0.458,3.333 6.875,3.531 6.417,0.198 10 false Front Seat Adjuster Assembly (Driver Seat) 4.823,0.552 5.281,0.75 0.458,0.198 10 false a29 4.813,1.063 5.271,1.26 0.458,0.198 10 false a30 4.813,2.094 5.271,2.292 0.458,0.198 10 false a31 4.823,1.573 5.281,1.771 0.458,0.198 10 false a31 4.333,0.313 4.792,0.51 0.458,0.198 10 false 6*1 4.833,0.313 5.292,0.51 0.458,0.198 10 false 6*2 4.344,0.823 4.802,1.021 0.458,0.198 10 false 5*1 4.813,0.823 5.271,1.021 0.458,0.198 10 false 5*2 4.292,1.344 4.906,1.542 0.615,0.198 10 false 25*1 4.781,1.344 5.396,1.542 0.615,0.198 10 false 25*2 4.292,1.844 4.906,2.042 0.615,0.198 10 false 12*1 4.771,1.844 5.385,2.042 0.615,0.198 10 false 12*2 4.333,0.542 4.792,0.74 0.458,0.198 10 false b10 4.323,1.063 4.781,1.26 0.458,0.198 10 false b11 4.323,2.083 4.781,2.281 0.458,0.198 10 false b22 4.323,1.573 4.781,1.771 0.458,0.198 10 false b22 5.219,0.542 5.833,0.74 0.615,0.198 10 false LFT+ 5.219,1.031 5.833,1.229 0.615,0.198 10 false LFT- 5.208,1.552 5.823,1.75 0.615,0.198 10 false SSRL 5.219,2.104 5.833,2.302 0.615,0.198 10 false SENG 4.823,2.594 6.792,3.167 1.969,0.573 10 false Position Control ECU Assembly (Driver Seat) 4.125,3.385 5.813,3.583 1.688,0.198 10 false *1: for LHD 5.156,3.375 6.844,3.573 1.688,0.198 10 false *2: for RHD

PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2653 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.PERFORM ACTIVE TEST USING GTS (SEAT LIFTER OPERATION)
3.PERFORM ACTIVE TEST USING GTS (SEAT LIFTER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Lifter Operation Seat lifter operation OFF/Down/Up -
Body Electrical > Driver Seat > Active Test
Tester Display
Lifter Operation
50004 162 2
OK:

Lifter motor operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)

NG

7.INSPECT POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)
4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)
a.

Disconnect the b7*1 or a36*2 power seat lifter motor assembly (driver seat) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
b7-2 - b7-3 Lifter switch on 4.8 to 5.1 V

for RHD
Tester Connection Condition Specified Condition
a36-2 - a36-3 Lifter switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

5.CHECK POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)

NG

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))
5.CHECK POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)
a.
B343020C64
1.75,0.167 2.167,0.417 0.417,0.25 1.063,0.167 1.479,0.417 0.417,0.25 0.156,0.146 0.396,0.396 0.24,0.25 10 false *a 1.844,0.208 2.219,0.479 0.375,0.271 10 false a36 1.198,0.219 1.51,0.417 0.313,0.198 10 false b7 1.5,0.188 1.813,0.385 0.313,0.198 12 false *A 2.198,0.198 2.51,0.396 0.313,0.198 12 false *B
*A for LHD
*B for RHD
*a Component with harness connected
(Power Seat Lifter Motor Assembly (Driver Seat))


Reconnect the b7*1 or a36*2 power seat lifter motor assembly (driver seat) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
b7-2 - Body ground Lifter motor operating 4.5 to 4.8 V

for RHD
Tester Connection Condition Specified Condition
a36-2 - Body ground Lifter motor operating 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY RH

NG

REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))
a.

Disconnect the b22*1 or a31*2 position control ECU assembly (driver seat) connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
b22-25 (SSRL) - b7-2 Always Below 1 Ω
b22-25 (SSRL) or b7-2 - Body ground Always 10 kΩ or higher
b22-12 (SENG) - b7-3 Always Below 1 Ω
b22-12 (SENG) or b7-3 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
a31-25 (SSRL) - a36-2 Always Below 1 Ω
a31-25 (SSRL) or a36-2 - Body ground Always 10 kΩ or higher
a31-12 (SENG) - a36-3 Always Below 1 Ω
a31-12 (SENG) or a36-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)
a.

Remove the power seat lifter motor assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


b.

Inspect the power seat lifter motor assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))

NG

REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))
a.

Disconnect the b10*1 and b11*1 or a29*2 and a30*2 position control ECU assembly (driver seat) connectors.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
b10-6 (LFT+) - b7-1 Always Below 1 Ω
b10-6 (LFT+) or b7-1 - Body ground Always 10 kΩ or higher
b11-5 (LFT-) - b7-4 Always Below 1 Ω
b11-5 (LFT-) or b7-4 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
a29-6 (LFT+) - a36-1 Always Below 1 Ω
a29-6 (LFT+) or a36-1 - Body ground Always 10 kΩ or higher
a30-5 (LFT-) - a36-4 Always Below 1 Ω
a30-5 (LFT-) or a36-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR