This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2658 | Short in Sensor with Motor Power Supply Circuit | Problem with the voltage supplied to the position control sensor. | ·
Position control ECU assembly (driver seat) ·
Slide motor (Upper seat track rail sub-assembly (driver seat)) ·
Power Seat Tilt Motor Assembly (Driver Seat) ·
Power Seat Lifter Motor Assembly (Driver Seat) ·
Reclining Motor (Front Seatback Frame Sub-assembly (Driver Seat)) ·
Wire harness or connector |
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
DTC B2658 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the b22*1 or a31*2 position control ECU assembly (driver seat) connector.
Disconnect the b5*1 or a28*2 slide motor (front seat adjuster assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b22-26 (SSRS) - b5-2 | Always | Below 1 Ω |
| b22-26 (SSRS) or b5-2 - Body ground | Always | 10 kΩ or higher |
| b22-12 (SENG) - b5-3 | Always | Below 1 Ω |
| b22-12 (SENG) or b5-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a31-26 (SSRS) - a28-2 | Always | Below 1 Ω |
| a31-26 (SSRS) or a28-2 - Body ground | Always | 10 kΩ or higher |
| a31-12 (SENG) - a28-3 | Always | Below 1 Ω |
| a31-12 (SENG) or a28-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the b5*1 or a28*2 slide motor (front seat adjuster assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b5-2 - b5-3 | Slide switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a28-2 - a28-3 | Slide switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the b22*1 or a31*2 position control ECU assembly (driver seat) connector.
Disconnect the b6*1 or a33*2 power seat tilt motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b22-10 (SSFV) - b6-2 | Always | Below 1 Ω |
| b22-10 (SSFV) or b6-2 - Body ground | Always | 10 kΩ or higher |
| b22-12 (SENG) - b6-3 | Always | Below 1 Ω |
| b22-12 (SENG) or b6-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a31-10 (SSFV) - a33-2 | Always | Below 1 Ω |
| a31-10 (SSFV) or a33-2 - Body ground | Always | 10 kΩ or higher |
| a31-12 (SENG) - a33-3 | Always | Below 1 Ω |
| a31-12 (SENG) or a33-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the b6*1 or a33*2 power seat tilt motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b6-2 - b6-3 | Front vertical switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a33-2 - a33-3 | Front vertical switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the b22*1 or a31*2 position control ECU assembly (driver seat) connector.
Disconnect the b7*1 or a36*2 power seat lifter motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b22-25 (SSRL) - b7-2 | Always | Below 1 Ω |
| b22-25 (SSRL) or b7-2 - Body ground | Always | 10 kΩ or higher |
| b22-12 (SENG) - b7-3 | Always | Below 1 Ω |
| b22-12 (SENG) or b7-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a31-25 (SSRL) - a36-2 | Always | Below 1 Ω |
| a31-25 (SSRL) or a36-2 - Body ground | Always | 10 kΩ or higher |
| a31-12 (SENG) - a36-3 | Always | Below 1 Ω |
| a31-12 (SENG) or a36-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the b7*1 or a36*2 power seat lifter motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b7-2 - b7-3 | Lifter switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a36-2 - a36-3 | Lifter switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the b22*1 or a31*2 position control ECU assembly (driver seat) connector.
Disconnect the c1*1 or q1*2 reclining motor (front seatback frame sub-assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b22-11 (SSRR) - c1-2 | Always | Below 1 Ω |
| b22-11 (SSRR) or c1-2 - Body ground | Always | 10 kΩ or higher |
| b22-12 (SENG) - c1-3 | Always | Below 1 Ω |
| b22-12 (SENG) or c1-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a31-11 (SSRR) - q1-2 | Always | Below 1 Ω |
| a31-11 (SSRR) or q1-2 - Body ground | Always | 10 kΩ or higher |
| a31-12 (SENG) - q1-3 | Always | Below 1 Ω |
| a31-12 (SENG) or q1-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the c1*1 or q1*2 reclining motor (front seatback frame sub-assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| c1-2 - c1-3 | Reclining switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| q1-2 - q1-3 | Reclining switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the power seat tilt motor assembly (driver seat) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the power seat lifter motor assembly (driver seat) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the slide motor (upper seat track rail sub-assembly (driver seat)) with a new or known good one.
Click hereVehicle Interior>SEAT>POWER SEAT TRACK RAIL ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the reclining motor (front seatback frame sub-assembly (driver seat)) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2685 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG