Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2018.04–2018.08
RM33C0E _53 Suspension _065440 TIRE PRESSURE MONITORING _0329663 TIRE PRESSURE WARNING SYSTEM U

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TERMINALS OF ECU  


CHECK TIRE PRESSURE WARNING ECU AND RECEIVER


a.
C361351C18
0.292,0.99 0.698,1.219 0.406,0.229 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 0.385,1.01 0.844,1.208 0.458,0.198 10 false R9
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the R9 tire pressure warning ECU and receiver connector and measure the voltage or resistance on the wire harness side.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R9-1 (IG) - R9-12 (GND) LA-B - BR IG power source Power switch on (IG) 10 to 16 V
R9-7 (+B) - R9-12 (GND) LA-R - BR Power supply (from auxiliary battery) Always 10 to 16 V
R9-9 (CANH) - R9-10 (CANL)* L - W CAN communication line Power switch off 54 to 69 Ω
R9-12 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω

*: w/ Tire Inflation Pressure Display Function



b.

Connect the R9 tire pressure warning ECU and receiver connector.


c.

Measure the voltage according to the value(s) in the table below. If the result is not as specified, the ECU may be malfunctioning.

HINT:

Measure the values on the wire harness side while the connector is connected.


E129452C64
1.927,0.865 2.333,1.073 0.406,0.208 0.115,0.094 0.438,0.344 0.323,0.25 10 false *a 2.031,0.885 2.323,1.083 0.292,0.198 10 false R9
*a Component with harness connected
(Tire Pressure Warning ECU and Receiver)
- -


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R9-3 (CLSW) - R9-12 (GND) SB - BR Tire pressure warning reset switch
·

Power switch on (IG)

·

Steering pad switch assembly operated, "Set Pressure" selected on the multi-information display and "OK" switch (steering pad switch assembly) pressed and held


Below 1.5 V
·

Power switch on (IG)

·

"OK" switch (steering pad switch assembly) off


8 to 15 V
R9-4 (RDA) - R9-12 (GND) GR - BR Output signals Power switch on (IG) Pulse generation (see waveform 1)
R9-5 (PRG) - R9-12 (GND) R - BR Input signals Power switch on (IG) Pulse generation (see waveform 1)


d.
C240058C03
2.875,1.229 3.115,1.438 0.24,0.208 10 false *b 0.115,0.104 0.323,0.323 0.208,0.219 10 false *a
*a Example
*b GND


Using an oscilloscope, check waveform 1.

Waveform 1:
Item Contents
Terminal R9-4 (RDA) - R9-12 (GND)
R9-5 (PRG) - R9-12 (GND)
Tool setting 5 V/DIV, 5 ms./DIV.
Vehicle condition Power switch on (IG)

HINT:

The waveform shown in the illustration is an example. If the tester displays a waveform that alternates between high and low, where high is a voltage that is between the IG power source voltage and a voltage 2.2 V lower than the IG power source voltage, and where low is a voltage of between 0 and 1.2 V, the ECU can be judged normal.