Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory) › 2018.04–2021.02
RM33C0E _59 Vehicle Exterior _065470 MIRROR (EXT) _0332577 POWER MIRROR CONTROL SYSTEM(w/ Memory) U

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)


B343031C29
4.813,0.167 5.188,0.417 0.375,0.25 2.802,0.167 3.177,0.417 0.375,0.25 2.083,0.167 2.458,0.417 0.375,0.25 4.125,0.167 4.5,0.417 0.375,0.25 4.917,0.208 5.375,0.406 0.458,0.198 10 false N9 2.49,0.208 2.948,0.406 0.458,0.198 10 false *A 2.865,0.198 3.323,0.396 0.458,0.198 10 false N10 2.177,0.198 2.635,0.396 0.458,0.198 10 false O9 3.219,0.208 3.677,0.406 0.458,0.198 10 false *B 4.219,0.208 4.677,0.406 0.458,0.198 10 false O8 5.229,0.198 5.688,0.396 0.458,0.198 10 false *B 4.542,0.208 5,0.406 0.458,0.198 10 false *A
*A for LHD *B for RHD


a.

Disconnect the O8*1 or N9*2 outer mirror control ECU assembly (driver door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O8-14 (BDR) - Body ground GR - Body ground +B power supply Power switch off 11 to 14 V
O8-6 (CPUB) - Body ground LA-L - Body ground +B power supply Power switch off 11 to 14 V
O8-5 (SIG) - Body ground LA-B - Body ground Ignition power supply Power switch off → on (IG) Below 1 V → 11 to 14 V
O8-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N9-14 (BDR) - Body ground GR - Body ground +B power supply Power switch off 11 to 14 V
N9-6 (CPUB) - Body ground LA-L - Body ground +B power supply Power switch off 11 to 14 V
N9-5 (SIG) - Body ground LA-B - Body ground Ignition power supply Power switch off → on (IG) Below 1 V → 11 to 14 V
N9-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the O8*1 or N9*2 outer mirror control ECU assembly (driver door) connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O9-3 (MR+) - Body ground B - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly (driver door) being retracted 11 to 14 V
Outer rear view mirror assembly (driver door) stopped Below 1 V
O9-11 (MR-) - Body ground L - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly (driver door) returning 11 to 14 V
Outer rear view mirror assembly (driver door) stopped Below 1 V
O9-1 (LMVR) - O9-10 (LM+R) BR - V Vertical mirror motor drive voltage Driver door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
O9-10 (LM+R) - O9-1 (LMVR) V - BR Vertical mirror motor drive voltage Driver door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
O9-10 (LM+R) - O9-9 (LMHR) V - LG Horizontal mirror motor drive voltage Driver door mirror surface moving right → stopped 11 to 14 V → Below 1 V
O9-9 (LMHR) - O9-10 (LM+R) LG - V Horizontal mirror motor drive voltage Driver door mirror surface moving left → stopped 11 to 14 V → Below 1 V
O9-5 (LVC) - O9-14 (LE1) G - BR Mirror position sensor power supply Power switch on (IG) 4.75 to 5.25 V
Power switch off Below 1 V
O9-6 (VSSR) - O8-7 (GND) V - W-B Mirror position sensor signal Power switch on (IG) 0 to 5 V
O9-13 (HSSR) - O8-7 (GND) GR - W-B Mirror position sensor signal Power switch on (IG) 0 to 5 V
O8-3 (M2) - O8-7 (GND) R - W-B M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
O8-2 (M1) - O8-7 (GND) BR - W-B M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
O8-1 (MM) - O8-7 (GND) GR - W-B SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N10-1 (RMVR) - N10-10 (RM+R) BR - V Vertical mirror motor drive voltage Driver door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
N10-10 (RM+R) - N10-1 (RMVR) V - BR Vertical mirror motor drive voltage Driver door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
N10-10 (RM+R) - N10-9 (RMHR) V - LG Horizontal mirror motor drive voltage Driver door mirror surface moving right → stopped 11 to 14 V → Below 1 V
N10-9 (RMHR) - N10-10 (RM+R) LG - V Horizontal mirror motor drive voltage Driver door mirror surface moving left → stopped 11 to 14 V → Below 1 V
N10-5 (RVC) - N10-14 (RE1) G - BR Mirror position sensor power supply Power switch on (IG) 4.75 to 5.25 V
Power switch off Below 1 V
N10-6 (VSSR) - N9-7 (GND) V - W-B Mirror position sensor signal Power switch on (IG) 0 to 5 V
N10-13 (HSSR) - N9-7 (GND) GR - W-B Mirror position sensor signal Power switch on (IG) 0 to 5 V
N9-3 (M2) - N9-7 (GND) R - W-B M2 switch signal for seat memory switch M2 switch on Below 1 V
M2 switch off 11 to 14 V
N9-2 (M1) - N9-7 (GND) BR - W-B M1 switch signal for seat memory switch M1 switch on Below 1 V
M1 switch off 11 to 14 V
N9-1 (MM) - N9-7 (GND) GR - W-B SET switch signal for seat memory switch SET switch on Below 1 V
SET switch off 11 to 14 V



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)


B343031C30
4.156,0.167 4.531,0.417 0.375,0.25 2.781,0.167 3.156,0.417 0.375,0.25 2.083,0.167 2.458,0.417 0.375,0.25 4.792,0.167 5.167,0.417 0.375,0.25 4.26,0.208 4.719,0.406 0.458,0.198 10 false N9 2.156,0.208 2.615,0.406 0.458,0.198 10 false N10 2.479,0.198 2.938,0.396 0.458,0.198 10 false *A 2.865,0.198 3.323,0.396 0.458,0.198 10 false O9 3.208,0.198 3.667,0.396 0.458,0.198 10 false *B 4.896,0.208 5.354,0.406 0.458,0.198 10 false O8 4.563,0.208 5.021,0.406 0.458,0.198 10 false *A 5.208,0.208 5.667,0.406 0.458,0.198 10 false *B
*A for LHD *B for RHD


a.

Disconnect the N9*1 or O8*2 outer mirror control ECU assembly (front passenger door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N9-14 (BDR) - Body ground GR - Body ground +B power supply Power switch off 11 to 14 V
N9-6 (CPUB) - Body ground LA-L - Body ground +B power supply Power switch off 11 to 14 V
N9-5 (SIG) - Body ground LA-B - Body ground Ignition power supply Power switch off → on (IG) Below 1 V → 11 to 14 V
N9-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O8-14 (BDR) - Body ground GR - Body ground +B power supply Power switch off 11 to 14 V
O8-6 (CPUB) - Body ground LA-L - Body ground +B power supply Power switch off 11 to 14 V
O8-5 (SIG) - Body ground LA-B - Body ground Ignition power supply Power switch off → on (IG) Below 1 V → 11 to 14 V
O8-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the N9*1 or O8*2 outer mirror control ECU assembly (front passenger door) connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N10-3 (MR+) - Body ground B - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly (front passenger door) being retracted 11 to 14 V
Outer rear view mirror assembly (front passenger door) stopped Below 1 V
N10-11 (MR-) - Body ground P - Body ground Power retract mirror motor drive voltage Outer rear view mirror assembly (front passenger door) returning 11 to 14 V
Outer rear view mirror assembly (front passenger door) stopped Below 1 V
N10-1 (RMVR) - N10-10 (RM+R) BR - V Vertical mirror motor drive voltage Front passenger door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
N10-10 (RM+R) - N10-1 (RMVR) V - BR Vertical mirror motor drive voltage Front passenger door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
N10-10 (RM+R) - N10-9 (RMHR) V - LG Horizontal mirror motor drive voltage Front passenger door mirror surface moving right → stopped 11 to 14 V → Below 1 V
N10-9 (RMHR) - N10-10 (RM+R) LG - V Horizontal mirror motor drive voltage Front passenger door mirror surface moving left → stopped 11 to 14 V → Below 1 V
N10-5 (RVC) - N10-14 (RE1) G - BR Mirror position sensor power supply Power switch on (IG) 4.75 to 5.25 V
Power switch off Below 1 V
N10-6 (VSSR) - N9-7 (GND) V - W-B Mirror position sensor signal Power switch on (IG) 0 to 5 V
N10-13 (HSSR) - N9-7 (GND) GR - W-B Mirror position sensor signal Power switch on (IG) 0 to 5 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O9-1 (LMVR) - O9-10 (LM+R) BR - V Vertical mirror motor drive voltage Front passenger door mirror surface moving upward → stopped 11 to 14 V → Below 1 V
O9-10 (LM+R) - O9-1 (LMVR) V - BR Vertical mirror motor drive voltage Front passenger door mirror surface moving downward → stopped 11 to 14 V → Below 1 V
O9-10 (LM+R) - O9-9 (LMHR) V - LG Horizontal mirror motor drive voltage Front passenger door mirror surface moving right → stopped 11 to 14 V → Below 1 V
O9-9 (LMHR) - O9-10 (LM+R) LG - V Horizontal mirror motor drive voltage Front passenger door mirror surface moving left → stopped 11 to 14 V → Below 1 V
O9-5 (LVC) - O9-14 (LE1) G - BR Mirror position sensor power supply Power switch on (IG) 4.75 to 5.25 V
Power switch off Below 1 V
O9-6 (VSSR) - O8-7 (GND) V - W-B Mirror position sensor signal Power switch on (IG) 0 to 5 V
O9-13 (HSSR) - O8-7 (GND) GR - W-B Mirror position sensor signal Power switch on (IG) 0 to 5 V



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


B472410C17
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 5.385,4.573 5.823,4.823 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.646,6.198 5.979,6.448 0.333,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 5.01,6.198 5.365,6.448 0.354,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 0.49,2.75 0.49,2.323 0.49,2.323 0.854,2.323 false 3.469,7.698 3.781,7.896 0.313,0.198 10 false MB 4.292,0.24 4.604,0.438 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false K51 2.052,1.479 2.365,1.677 0.313,0.198 10 false K52 2.052,1.802 2.365,2 0.313,0.198 10 false K53 0.875,1.083 1.188,1.281 0.313,0.198 10 false 3D 0.875,1.667 1.188,1.865 0.313,0.198 10 false 3C 0.885,2.031 1.198,2.229 0.313,0.198 10 false 3E 5.854,1.146 6.167,1.344 0.313,0.198 10 false 3B 5.854,1.76 6.167,1.958 0.313,0.198 10 false 3A 1.219,3.302 1.531,3.5 0.313,0.198 10 false K53 3.25,3.271 3.563,3.469 0.313,0.198 10 false K52 5.542,3.26 5.854,3.458 0.313,0.198 10 false K51 1.844,4.625 2.156,4.823 0.313,0.198 10 false 3A 1.229,6.219 1.542,6.417 0.313,0.198 10 false 3C 3.792,6.167 4.104,6.365 0.313,0.198 10 false 3D 5.104,6.24 5.417,6.438 0.313,0.198 10 false 3F 6.448,6.25 6.76,6.448 0.313,0.198 10 false 3E 5.51,4.625 5.823,4.823 0.313,0.198 10 false 3B 0.354,2.781 0.729,3.01 0.375,0.229 10 false 3F*A 0.344,2.948 0.719,3.177 0.375,0.229 10 false 3G*B 5.729,6.24 6.042,6.438 0.313,0.198 10 false 3G 5.406,6.24 5.719,6.438 0.313,0.198 10 false *A 6.021,6.24 6.333,6.438 0.313,0.198 10 false *B
*A for LHD *B for RHD


a.

Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-31 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply (IG signal) Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
MB-30 (ACC) - Body ground - Ignition power supply (ACC signal) Power switch on (ACC) 11 to 14 V
Power switch off Below 1 V
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω


d.

Connect the main body ECU (multiplex network body ECU) connectors.


e.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
K53-7 (MIRB) - K53-9 (MIRE) L - W Mirror surface adjust switch signal
·

Power switch on (ACC)

·

Mirror surface adjust switch up


Below 1.7 V
·

Power switch on (ACC)

·

Mirror surface adjust switch right


Below 2.7 V
·

Power switch on (ACC)

·

Mirror surface adjust switch down


Below 3.5 V
·

Power switch on (ACC)

·

Mirror surface adjust switch left


Below 4 V
·

Power switch on (ACC)

·

Mirror surface adjust switch off


3.8 to 5 V
K53-8 (MIRS) - K53-9 (MIRE) GR - W Mirror select switch signal
·

Power switch on (ACC)

·

Mirror select switch L


Below 2 V
·

Power switch on (ACC)

·

Mirror select switch R


Below 1 V
·

Power switch on (ACC)

·

Mirror select switch off


3.8 to 5.0 V
K53-16 (RET) - K53-9 (MIRE)* B - W Retractable outer mirror switch signal
·

Power switch on (ACC)

·

Retractable outer mirror switch not in return position


Pulse generation (See waveform 1 or 2)
·

Power switch on (ACC)

·

Retractable outer mirror switch in return position


Below 1 V

*: w/ Power Retract Mirror



f.
B244640N02
0.135,1.198 0.594,1.396 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Tester Connection K53-16 (RET) - K53-9 (MIRE)
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition
·

Power switch on (ACC)

·

Retractable outer mirror switch not in return position




g.
B244641N02
0.135,0.979 0.594,1.177 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Tester Connection K53-16 (RET) - K53-9 (MIRE)
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition
·

Power switch on (ACC)

·

Retractable outer mirror switch not in retract position