The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle carrier sub-assembly removal/installation are shown below.
When removing or installing the rear disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISABLE BRAKE CONTROL
Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>REMOVAL
3.REMOVE REAR WHEEL
890C0A
4.SEPARATE NO. 2 PARKING BRAKE WIRE ASSEMBLY
Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.
Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.
Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disconnect the No. 2 parking brake wire assembly connector from the rear axle hub and bearing assembly.
Be careful not to damage the rear axle hub and bearing assembly or connector cover.
Remove the nut, disengage the 2 clamps and separate the No. 2 parking brake wire assembly from the rear flexible hose bracket and rear trailing arm assembly.
47319F
5.SEPARATE REAR FLEXIBLE HOSE
Remove the bolt and separate the rear flexible hose from the rear flexible hose bracket.
6.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY
42431
7.REMOVE REAR DISC
Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL
42450B
8.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY
9.REMOVE REAR FLEXIBLE HOSE BRACKET
Remove the bolt and rear flexible hose bracket from the rear axle carrier sub-assembly.
89408C
10.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)
for LH Side:
Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL
48840A
11.REMOVE REAR STABILIZER LINK ASSEMBLY
48231B
12.REMOVE REAR COIL SPRING
48258C
13.REMOVE REAR LOWER COIL SPRING INSULATOR
48720A
14.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY
42305
15.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY
Loosen the 2 bolts of the rear trailing arm assembly.
| *1 | Rear Axle Carrier Pin |
Loosen the nut of the rear shock absorber assembly.
Hold the rear axle carrier pin while rotating the nut.
| *a | Wooden Block |
| *b | Jack |
Using a jack and a wooden block, support the rear axle carrier sub-assembly.
When jacking up the rear axle carrier sub-assembly, be sure to jack it up slowly.
Make sure to perform this operation with the vehicle kept as low as possible.
Loosen the bolt (A).
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
Remove the 2 bolts and separate the rear trailing arm assembly from the rear axle carrier sub-assembly.
Remove the nut and plate washer, and separate the rear shock absorber assembly from the rear axle carrier sub-assembly.
Hold the rear axle carrier pin while rotating the nut.
Remove the bolt (A), nut and rear axle carrier sub-assembly from the rear upper control arm assembly.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.