Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2018.04–2020.08
RM33C0E _51 Engine / Hybrid System _065419 A25A-FXS ENGINE CONTROL _0331447 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P05A211  Active Grille Air Shutter "A" Circuit Short to Ground  P05A212  Active Grille Air Shutter "A" Circuit Short to Battery  P05A213  Active Grille Air Shutter "A" Circuit Open  


DESCRIPTION

HINT:

These DTCs are applicable to models w/ Grille Shutter System only.


Refer to DTC P059F73.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P059F73

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P05A211 Active Grille Air Shutter "A" Circuit Short to Ground Either of the following conditions is met and the ECM receives a malfunction signal 17 times* (1 trip detection logic):
·

Short to ground detected in the grille shutter motor (swing grille actuator assembly) when a grille shutter operation is requested.

·

Short to ground detected in the motor drive circuit when a grille shutter operation is requested.


Swing grille actuator assembly Does not come on DTC stored SAE Code: P05A5
P05A212 Active Grille Air Shutter "A" Circuit Short to Battery Either of the following conditions is met and the ECM receives a malfunction signal 17 times* (1 trip detection logic):
·

Short to +B detected in the grille shutter motor (swing grille actuator assembly) when a grille shutter operation is requested.

·

Short to +B detected in the motor drive circuit when a grille shutter operation is requested.


Swing grille actuator assembly Does not come on DTC stored SAE Code: P05A4
P05A213 Active Grille Air Shutter "A" Circuit Open Either of the following conditions is met and the ECM receives a malfunction signal 17 times* (1 trip detection logic):
·

Open detected in the grille shutter motor (swing grille actuator assembly) when a grille shutter operation is requested.

·

Open detected in the grille shutter motor circuit when a grille shutter operation is requested.

·

Internal malfunction detected in the grille shutter ECU (swing grille actuator assembly) when a grille shutter operation is requested.


Swing grille actuator assembly Does not come on DTC stored SAE Code: P05A2

HINT:

*: For every 65 ms that the ECM receives a grille shutter system malfunction signal from the grille shutter ECU (swing grille actuator assembly) the ECM determines it has received the signal 1 time. If the ECM determines the malfunction signal has been received 17 consecutive times (the signal is received for approximately 1 second continuously), it will store a DTC.


MONITOR DESCRIPTION

1.

Grille Shutter Motor (Swing Grille Actuator Assembly) Malfunction

If the grille shutter ECU (swing grille actuator assembly) detects a malfunction in the grille shutter motor drive circuit when a grille shutter operation is requested, it will output a malfunction signal to the ECM and the ECM will store a DTC.

Detection Condition DTC No.
Short to Ground P05A211 (Active Grille Air Shutter "A" Circuit Short to Ground)
Short to +B P05A212 (Active Grille Air Shutter "A" Circuit Short to Battery)
Open P05A213 (Active Grille Air Shutter "A" Circuit Open)

2.

Grille Shutter ECU Internal Malfunction

If the grille shutter ECU detects an internal malfunction, it will output a malfunction signal to the ECM and the ECM will store a DTC.

Detection Condition DTC No.
EEPROM Malfunction P05A213 (Active Grille Air Shutter "A" Circuit Open)
Analog/Digital Conversion Malfunction


CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Control Mode Switching.

9.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

10.

Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

11.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.


12.

Enter the following menus: Body Electrical / Grill Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

13.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.



CAUTION / NOTICE / HINT

NOTICE:
·

In order to ensure safety, before performing troubleshooting or removing the swing grille actuator assembly or radiator shutter sub-assembly, change the grille shutter control mode to maintenance mode.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM UTILITY USING GTS (GRILL SHUTTER CONTROL MODE SWITCHING)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Control Mode Switching.

Body Electrical > Grill Shutter > Utility
Tester Display
Grill Shutter Control Mode Switching
50005 352 4221

e.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.


Result:
Proceed to
NEXT



NEXT

2.REPLACE SWING GRILLE ACTUATOR ASSEMBLY
2.REPLACE SWING GRILLE ACTUATOR ASSEMBLY
a.

Replace the swing grille actuator assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

3.PERFORM UTILITY USING GTS (GRILL SHUTTER CONTROL MODE SWITCHING AND GRILL SHUTTER INITIALIZATION)
3.PERFORM UTILITY USING GTS (GRILL SHUTTER CONTROL MODE SWITCHING AND GRILL SHUTTER INITIALIZATION)
HINT:

When changing the grille shutter control mode and/or performing initialization by driving the vehicle, the grille shutter control mode can only be changed and initialization can only be performed if the grille shutter system is in maintenance mode.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>INITIALIZATION


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Control Mode Switching.

Body Electrical > Grill Shutter > Utility
Tester Display
Grill Shutter Control Mode Switching
50005 352 4221

e.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.


f.

Enter the following menus: Body Electrical / Grill Shutter / Utility / Grill Shutter Initialization.

Body Electrical > Grill Shutter > Utility
Tester Display
Grill Shutter Initialization
50005 352 4467

g.

According to the display on the GTS, perform Grill Shutter Initialization.


h.

Enter the following menus: Body Electrical / Grill Shutter / Data List / Shutter Control State and Shutter Initialization.

Body Electrical > Grill Shutter > Data List
Tester Display
Shutter Control State
Shutter Initialization
50003 352 10,29

i.

According to the display on the GTS, read the Data List and check that the value of Shutter Control State is "Normal" and Shutter Initialization is "Complete".


Result:
Proceed to
NEXT



NEXT

END