This DTC is stored when the blind spot monitor sensor RH detects a short to +B in the outer rear view mirror indicator RH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AB0 | Short to +B in Outer Mirror Indicator(Master) | Both of the following conditions are met:
·
The blind spot monitor system is on ·
The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time |
·
Outer mirror RH ·
Outer rear view mirror assembly with cover RH ·
Wire harness or connector ·
Blind spot monitor sensor RH |
When checking for DTCs, make sure that the blind spot monitor system is turned on.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Turn the power switch off.
Turn the power switch on (IG).
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the W5 blind spot monitor sensor RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W5-4 (OMIR) - Body ground | Power switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the IND1 outer mirror RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W5-4 (OMIR) - Body ground | Power switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch off.
Turn the power switch on (IG).
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the N17 outer rear view mirror assembly with cover RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W5-4 (OMIR) - Body ground | Power switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the W5 blind spot monitor sensor RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W5-4 (OMIR) - Body ground | Power switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the IND1 outer mirror RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W5-4 (OMIR) - Body ground | Power switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N19 outer rear view mirror assembly with cover RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W5-4 (OMIR) - Body ground | Power switch on (IG) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG