This DTC is stored when the blind spot monitor sensor RH detects a short to ground in the outer rear view mirror indicator RH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AB2 | Short to GND in Outer Mirror Indicator(Master) | Both of the following conditions are met:
·
The blind spot monitor system is on ·
The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time |
·
Outer mirror RH ·
Outer rear view mirror assembly with cover RH ·
Wire harness or connector ·
Blind spot monitor sensor RH |
When checking for DTCs, make sure that the blind spot monitor system is turned on.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Turn the power switch off.
Turn the power switch on (IG).
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the W5 blind spot monitor sensor RH connector.
Disconnect the N17 outer rear view mirror assembly with cover RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W5-4 (OMIR) or N17-8 (BSR+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the IND1 outer mirror RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N17-8 (BSR+) or IND1-2 (+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer mirror RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL
Inspect the outer rear view mirror indicator RH on the outer mirror RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch off.
Turn the power switch on (IG).
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the W5 blind spot monitor sensor RH connector.
Disconnect the N19 outer rear view mirror assembly with cover RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W5-4 (OMIR) or N19-3 (BSR+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the IND1 outer mirror RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N19-3 (BSR+) or IND1-2 (+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer mirror RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL
Inspect the outer rear view mirror indicator RH on the outer mirror RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG