Home › Suspension › REAR SUSPENSION › REAR TRAILING ARM › 2018.04–2019.02
RM33C0E _53 Suspension _065439 REAR SUSPENSION _0331925 REAR TRAILING ARM A

REAR SUSPENSION  REAR TRAILING ARM  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48727 1.INSTALL REAR SUSPENSION ARM BRACKET

a.
C370221

Temporarily install the rear suspension arm bracket to the rear trailing arm assembly with the bolt and nut.

NOTICE:

Insert the bolt from the inside of the vehicle.



b.
C379242C01
1.573,1 1.656,0.698 1.656,0.698 1.896,0.698 false 1.938,0.615 2.25,0.792 0.313,0.177 10 false *a 3.031,1.271 3.281,1.531 0.25,0.26 10 false A
*a Upper Surface of Rear Suspension Arm Bracket


Position the rear trailing arm assembly as shown in the illustration.

Reference Length (A):

120 mm (4.72 in.)



c.

Fully tighten the nut.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


Hide 48738 2.INSTALL REAR SUSPENSION ARM COVER

a.

Engage the 4 claws and install the rear suspension arm cover.


Hide 48780E 3.INSTALL REAR TRAILING ARM ASSEMBLY

a.

Using a transmission jack and a wooden block, support the rear No. 2 suspension arm assembly.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




b.

Install the rear trailing arm assembly to the vehicle with the 4 bolts.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)


c.

Install the rear trailing arm assembly to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
135 N*m (1377 kgf*cm, 100 ft.*lbf)


Hide 890C0A 4.INSTALL NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.

Install the No. 2 parking brake wire assembly to the rear trailing arm assembly with the nut.

Torque:
15.5 N*m (158 kgf*cm, 11 ft.*lbf)


b.

Engage the 2 clamps.


Hide 48840A 5.INSTALL REAR STABILIZER LINK ASSEMBLY

Hide 58398F 6.INSTALL NO. 1 FLOOR UNDER COVER (w/ Cover)

a.

for RH Side:

i.
C379125N01
1.458,0.073 1.635,0.24 0.177,0.167 10 true A 2.115,0.042 2.292,0.208 0.177,0.167 10 true B 0.51,0.75 0.688,0.917 0.177,0.167 10 true B

Install the No. 1 floor under cover with the 2 grommets (B).


ii.

Install the bolt and clip (A).

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)



Hide 58399D 7.INSTALL NO. 2 FLOOR UNDER COVER (w/ Cover)

a.

for LH Side:

i.
C379124N01
1.969,0.125 2.104,0.302 0.135,0.177 10 true A 2.729,0.76 2.865,0.938 0.135,0.177 10 true B 1.5,0.063 1.635,0.24 0.135,0.177 10 true B 0.552,1.063 0.688,1.24 0.135,0.177 10 true C

Install the No. 2 floor under cover with the 2 grommets (B) and clip (C).


ii.

Install the bolt and clip (A).

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)



Hide 8.INSTALL REAR WHEEL

Hide 9.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 10.PERFORM INITIALIZATION

Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)