88625
1.INSTALL NO. 1 COOLER THERMISTOR
88501
2.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
Install the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor to the upper heater case.
Engage the clamp.
Engage the 10 claws to install the upper heater case with No. 1 cooler evaporator sub-assembly to the lower heater case.
Install the 2 screws.
88515
3.INSTALL COOLER EXPANSION VALVE
Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 1 cooler evaporator sub-assembly.
ND-OIL 11 or equivalent
Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 hexagon bolts.
88899L
4.INSTALL GROMMET SUB-ASSEMBLY
Install the grommet sub-assembly.
87107A
5.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
|
Install in this Direction |
Install the heater radiator unit sub-assembly as shown in the illustration.
87124B
6.INSTALL HEATER CLAMP
Engage the 3 claws to install the heater clamp.
88897M
7.INSTALL HEATER PIPE GROMMET
| *a | Reference Point |
Install the heater pipe grommet as shown in the illustration.
Install the heater pipe grommet with the arrow facing up.
87050E
8.INSTALL NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for 3 Zone Type)
Align each gear on the air conditioning radiator assembly as shown in the illustration, and then check that the gears of the No. 3 air conditioning radiator damper servo sub-assembly are aligned as shown in the illustration.
| *a | Reference Point | - | - |
Install the No. 3 air conditioning radiator damper servo sub-assembly with the 2 screws.
87050D
9.INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
for LHD:
| *a | Reference Point |
Using the reference points, install the No. 2 air conditioning radiator damper servo sub-assembly with the 2 screws.
for RHD:
| *a | Reference Point |
Using the reference points, install the No. 2 air conditioning radiator damper servo sub-assembly with the 2 screws.
87050C
10.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Align each gear on the air conditioning radiator assembly as shown in the illustration, and then check that the gears of the No. 1 air conditioning radiator damper servo sub-assembly are aligned as shown in the illustration.
| *a | Reference Point | - | - |
| *a | Reference Point |
Using the reference points, install the No. 1 air conditioning radiator damper servo sub-assembly with the 3 screws.
88539J
11.INSTALL DRAIN COOLER HOSE
| *a | Hose Notch |
| *b | Rib |
Align the hose notch with the rib as shown in the illustration and install the drain cooler hose.
87114B
12.INSTALL HEATER COVER
|
Install in this Direction |
Install the heater cover as shown in the illustration.
Install the screw.
82210K
13.INSTALL AIR CONDITIONING HARNESS ASSEMBLY
for LHD:
| *A | for 3 Zone Type |
Engage each clamp.
Connect each connector to install the air conditioning harness assembly.
for RHD:
Engage each clamp.
Connect each connector to install the air conditioning harness assembly.
88650N
14.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY
for LHD:
|
Install in this Direction |
Engage the guide to temporarily install the air conditioning amplifier assembly as shown in the illustration.
Install the air conditioning amplifier assembly with the screw.
Connect the connector.
for RHD:
|
Install in this Direction |
Engage the guide to temporarily install the air conditioning amplifier assembly as shown in the illustration.
Install the air conditioning amplifier assembly with the screw.
Connect the connector.
87130D
15.INSTALL BLOWER ASSEMBLY
88897P
16.INSTALL ASPIRATOR
Engage the 2 claws and guide to install the aspirator.
87211A
17.INSTALL NO. 2 AIR DUCT
Engage the 3 claws.
Install a new No. 2 air duct with the screw.