The drive start control is controlled by the hybrid vehicle control ECU assembly.
If the hybrid vehicle control ECU assembly determines that the shift lever and accelerator pedal are operated abnormally, driving force is restricted and, when necessary, a warning is displayed on the combination meter assembly.
Even if the accelerator pedal position is maintained, the driving force may increase when driving uphill and decrease when driving downhill. This is due to drive start control controlling the driving force, and is not a malfunction.
Interview the customer to confirm the problem.
| Result | Proceed to |
|---|---|
| Hunting | A |
| Hesitation/poor acceleration | B |
A
B
Check if the customer operated the vehicle in a way that would cause the drive start control to operate.
Activation conditions
Pattern A (When all of the following conditions are met, control starts.)
The accelerator pedal is open by approximately 1/5 or more.
The shift lever is moved from P to (D or S) or R.
Pattern B (When all of the following conditions are met, control starts.)
The accelerator pedal is open by approximately 1/5 or more.
The shift lever is moved from R to (D or S), from (D or S) or N to R.
Items Controlled
Driving force is restricted.
Deactivation Conditions
The accelerator pedal is released.
The shift lever is in P or N.
Activation conditions
The shift lever is in R.
The accelerator pedal is depressed excessively.
Items Controlled
Driving force is restricted.
Deactivation Conditions
The accelerator pedal is released.
The shift lever is moved to any position other than R.
The driving force restricted level differs between Pattern A, Pattern B and Reverse control.
During Shift control or Reverse control, driving force is adjusted based on the road gradient.
| Result | Proceed to |
|---|---|
| Performed | A |
| Not performed | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: System Select / Health Check.
Check the DTCs.
Turn the power switch off.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC is output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
| RR Wheel Speed |
| RL Wheel Speed |
Read the values displayed on the GTS.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| FR Wheel Speed
FL Wheel Speed RR Wheel Speed RL Wheel Speed |
Vehicle stopped | 0 km/h (0 mph) |
| Vehicle being driven at constant speed between 16 to 64 km/h (10 to 40 mph) | No large fluctuations when driving at a constant speed |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Turn the GTS on.
Enter the following menus: Powertrain / Hybrid Control / Data List / Vehicle Speed.
| Tester Display |
|---|
| Vehicle Speed |
Read the value displayed on the GTS.
| Inspection Condition | Specified Condition |
|---|---|
| Vehicle stopped | 0 km/h (0 mph) |
| Vehicle being driven at a constant speed
(16 to 64 km/h (10 to 40 mph)) |
No large fluctuations in displayed speed |
Perform this road test only in an appropriate safe location, in accordance with all local laws.
Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Deceleration Sensor and Deceleration Sensor2.
| Tester Display |
|---|
| Deceleration Sensor |
| Deceleration Sensor2 |
Read the value displayed on the GTS.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Deceleration Sensor
Deceleration Sensor2 |
During deceleration | Value changes with vehicle speed |
| During acceleration | Value changes with vehicle speed |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Steering Angle Sensor.
| Tester Display |
|---|
| Steering Angle Sensor |
Read the value displayed on the GTS.
| Condition | Specified Condition |
|---|---|
| Steering wheel turned left | Value increases with steering wheel operation |
| Steering wheel turned right | Value decreases with steering wheel operation |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if the customer operated the vehicle in a way that would cause the drive start control to operate.
Activation conditions
Pattern A (When all of the following conditions are met, control starts.)
The accelerator pedal is open by approximately 1/5 or more.
The shift lever is moved from P to (D or S) or R.
Pattern B (When all of the following conditions are met, control starts.)
The accelerator pedal is open by approximately 1/5 or more.
The shift lever is moved from R to (D or S), from (D or S) or N to R.
Items Controlled
Driving force is restricted.
Deactivation Conditions
The accelerator pedal is released.
The shift lever is in P or N.
Activation conditions
The shift lever is in R.
The accelerator pedal is depressed excessively.
Items Controlled
Driving force is restricted.
Deactivation Conditions
The accelerator pedal is released.
The shift lever is moved to any position other than R.
The driving force restricted level differs between Pattern A, Pattern B and Reverse control.
During Shift control or Reverse control, driving force is adjusted based on the road gradient.
| Result | Proceed to |
|---|---|
| Not performed | A |
| Performed | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: System Select / Health Check.
Check the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC is output | B |
Turn the power switch off.
A
B
Inspect the shift lever position sensor.
Click hereDrivetrain>P710 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT LEVER POSITION SENSOR>INSPECTION
| Result | Proceed to |
|---|---|
| Normal | A |
| Abnormal | B |
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>ACCELERATOR PEDAL SENSOR>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG