Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2018.08–2019.02
RM33C0E _56 Audio / Visual / Telematics _065451 NAVIGATION / MULTI INFO DISPLAY _0333738 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transmits signals via AVC-LAN communication.

If a short to +B or short to ground occurs in an AVC-LAN communication line, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E388602E01
4.729,1.365 5.344,1.563 0.615,0.198 10 false K3 4.729,1.531 6.438,1.958 1.708,0.427 10 false Radio and Display Receiver Assembly 1.813,0.49 2.427,0.688 0.615,0.198 10 false TX+ 1.833,0.865 2.448,1.063 0.615,0.198 10 false TX- 2.156,0.354 2.771,0.552 0.615,0.198 10 false 8 2.167,0.74 2.781,0.938 0.615,0.198 10 false 7 1.042,2.302 3.281,2.542 2.24,0.24 10 false : AVC-LAN Communication Line 4.917,0.354 5.531,0.552 0.615,0.198 10 false 5 4.917,0.75 5.531,0.948 0.615,0.198 10 false 6 5.094,0.49 5.708,0.688 0.615,0.198 10 false TX1+ 5.104,0.875 5.719,1.073 0.615,0.198 10 false TX1- 0.74,1.354 1.354,1.552 0.615,0.198 10 false K9 0.729,1.531 2.469,1.969 1.74,0.438 10 false Stereo Component Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.




HINT:

The radio and display receiver assembly is the master unit.


PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.
E382042C03
1.615,0.333 2.021,0.583 0.406,0.25 2.323,1.729 2.563,1.25 false 2.906,1.708 2.698,1.25 false 2.844,1.771 3.302,2.01 0.458,0.24 10 false TX1+ 2.188,1.76 2.646,2 0.458,0.24 10 false TX1- 1.74,0.385 2.198,0.625 0.458,0.24 10 false K3 0.135,0.125 0.594,0.365 0.458,0.24 10 false *a
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K3-5 (TX1+) - K3-6 (TX1-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the K3 radio and display receiver assembly connector.


b.

Disconnect the K9 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K3-5 (TX1+) - K9-8 (TX+) Always Below 1 Ω
K3-6 (TX1-) - K9-7 (TX-) Always Below 1 Ω
K3-5 (TX1+) or K9-8 (TX+) - Body ground Always 10 kΩ or higher
K3-6 (TX1-) or K9-7 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY