Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2018.08
RM33C0E _56 Audio / Visual / Telematics _065451 NAVIGATION / MULTI INFO DISPLAY _0333738 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E379007E57
1.542,0.271 2.688,0.531 1.146,0.26 10 false to Other Systems 2.115,1.417 2.427,1.615 0.313,0.198 10 false +S 2.427,1.292 2.74,1.49 0.313,0.198 10 false 6 4.573,1.313 4.885,1.51 0.313,0.198 10 false 11 4.823,1.417 5.271,1.635 0.448,0.219 10 false SPD 4.302,2.094 5.135,2.302 0.833,0.208 10 false K9 4.302,2.26 6.771,2.531 2.469,0.271 10 false Stereo Component Amplifier Assembly 1.01,2.073 1.781,2.271 0.771,0.198 10 false K21 1.01,2.24 2.979,2.594 1.969,0.354 10 false Combination Meter Assembly

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E256135C77
1.5,0.417 1.917,0.667 0.417,0.25 2.542,1.99 2.208,1.344 false 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.583,0.458 1.979,0.667 0.396,0.208 10 false K21 2.49,2 2.802,2.198 0.313,0.198 10 false +S 2.792,3.594 3.188,3.865 0.396,0.271 10 false GND 1.125,3.875 1.521,4.146 0.396,0.271 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connectors still connected.


ii.

Connect an oscilloscope to terminal K21-6 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal K21-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)

NG

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)
a.

Check the input waveform.

E265796C39
1.604,0.385 2.01,0.667 0.406,0.281 1.146,1.958 1.344,1.313 false 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 1.719,0.427 2.031,0.625 0.313,0.198 10 false K9 1,1.99 1.469,2.229 0.469,0.24 10 false SPD 4.573,1.813 4.885,2.01 0.313,0.198 10 false A 5.969,1.563 6.469,1.854 0.5,0.292 10 false GND
*a Component with harness connected
(Stereo Component Amplifier Assembly)
- -


i.

Remove the stereo component amplifier assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal K9-11 (SPD) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal K9-11 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR