CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A29-26 (DB1) - K69-6 (E1) | W - W-B | D shift position signal | Power switch on (IG), shift lever in D | 7.5 to 14 V |
| Power switch on (IG), shift lever not in D | Below 1 V | |||
| A29-14 (DB2) - K69-6 (E1) | V - W-B | D shift position signal | Power switch on (IG), shift lever in D | 7.5 to 14 V |
| Power switch on (IG), shift lever not in D | Below 1 V | |||
| K70-1 (M) - K69-6 (E1) | B - W-B | S shift position signal | Power switch on (IG), shift lever in S | 11 to 14 V |
| Power switch on (IG), shift lever not in S | Below 1 V | |||
| A28-15 (STP) - K69-6 (E1) | LA-G - W-B | Stop light switch signal | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1 V | |||
| K69-28 (CCS) - K69-6 (E1) | GR - W-B | Steering pad switch circuit | Cruise control switch not pushed | 1 MΩ or higher |
| Cruise control main switch pushed | Below 2.5 Ω | |||
| +RES switch pushed | 617 to 643 Ω | |||
| -SET switch pushed | 1509 to 1571 Ω | |||
| CANCEL switch pushed | 235 to 245 Ω | |||
| A29-28 (ST1-) - K69-6 (E1) | LG - W-B | Stop light switch signal | Power switch on (IG), brake pedal depressed | Below 1 V |
| Power switch on (IG), brake pedal released | 7.5 to 14 V | |||
| K70-8 (SFTD) - K69-6 (E1) | G - W-B*1
W - W-B*2 |
Down-shift position switch signal | Power switch on (IG), shift lever in S | 11 to 14 V |
| Power switch on (IG), shift lever in "-" | Below 1 V | |||
| K70-9 (SFTU) - K69-6 (E1) | L - W-B*1
LG - W-B*2 |
Up-shift position switch signal | Power switch on (IG), shift lever in S | 11 to 14 V |
| Power switch on (IG), shift lever in "+" | Below 1 V |
*1: w/o Shift Paddle Switch
*2: w/ Shift Paddle Switch
CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A30-1 (SGND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| A30-2 (CA2L) - A30-1 (SGND) | W - W-B | CAN communication signal | Power switch on (IG) | Pulse generation
(See waveform 2) |
| A30-3 (CA2H) - A30-1 (SGND) | R - W-B | CAN communication signal | Power switch on (IG) | Pulse generation
(See waveform 1) |
| A30-5 (CA1P) - A30-1 (SGND) | G - W-B | CAN communication signal | Power switch on (IG) | Pulse generation
(See waveform 1) |
| A30-6 (CA1N) - A30-1 (SGND) | W - W-B | CAN communication signal | Power switch on (IG) | Pulse generation
(See waveform 2) |
| A30-8 (IGB) - A30-1 (SGND) | B - W-B | Power source | Power switch on (IG) | 11 to 14 V |
Waveform 1
CAN communication signal
| Item | Content |
|---|---|
| Tester Connection | ·
Between A30-3 (CA2H) and A30-1 (SGND) ·
Between A30-5 (CA1P) and A30-1 (SGND) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Power switch on (IG) |
The waveform varies depending on the CAN communication signal.
Waveform 2
CAN communication signal
| Item | Content |
|---|---|
| Tester Connection | ·
Between A30-2 (CA2L) and A30-1 (SGND) ·
Between A30-6 (CA1N) and A30-1 (SGND) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Power switch on (IG) |
The waveform varies depending on the CAN communication signal.
CHECK FORWARD RECOGNITION CAMERA
DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.
Do not apply excessive force to the V6 forward recognition camera connector.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| V6-7 (IGB) - V6-10 (GND) | LA-P - LA*1
LA-P - W-B*2 |
Power source | Power switch on (IG) | 11 to 14 V |
| Power switch off | Below 1 V | |||
| V6-5 (CA1P) - V6-10 (GND) | L - LA*1
L - W-B*2 |
CAN communication signal | Power switch on (IG) | Pulse generation
(See waveform 1) |
| V6-11 (CA1N) - V6-10 (GND) | W - LA*1
W - W-B*2 |
CAN communication signal | Power switch on (IG) | Pulse generation
(See waveform 2) |
| V6-6 (CANH) - V6-10 (GND) | G - LA*1
G - W-B*2 |
CAN communication signal | Power switch on (IG) | Pulse generation
(See waveform 1) |
| V6-12 (CANL) - V6-10 (GND) | W - LA*1
W - W-B*2 |
CAN communication signal | Power switch on (IG) | Pulse generation
(See waveform 2) |
| V6-3 (LKSW) - V6-10 (GND) | V - LA*1
V - W-B*2 |
Vehicle-to-vehicle distance control switch signal | Power switch on (IG), vehicle-to-vehicle distance control switch not pushed | 4.75 to 5.25 V |
| Power switch on (IG), vehicle-to-vehicle distance control switch pushed | Below 1 V | |||
| V6-10 (GND) - Body ground | LA - Body ground*1
W-B - Body ground*1 |
Ground | Always | Below 1 Ω |
*1: through No. 29 Junction Connector
*2: not through No. 29 Junction Connector
Waveform 1
CAN communication signal
| Item | Content |
|---|---|
| Tester Connection | ·
Between V6-5 (CA1P) and V6-10 (GND) ·
Between V6-6 (CANH) and V6-10 (GND) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Power switch on (IG) |
The waveform varies depending on the CAN communication signal.
Waveform 2
CAN communication signal
| Item | Content |
|---|---|
| Tester Connection | ·
Between V6-11 (CA1N) and V6-10 (GND) ·
Between V6-12 (CANL) and V6-10 (GND) |
| Tool Setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Power switch on (IG) |
The waveform varies depending on the CAN communication signal.