Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2018.08–2021.02
RM33C0E _58 Vehicle Interior _065461 PRE-COLLISION _0332154 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U1002  Lost Communication with Gateway Module  


DESCRIPTION

DTC U1002 is stored when the millimeter wave radar sensor assembly cannot receive signals from the forward recognition camera.

DTC No. Detection Item DTC Detection Condition Trouble Area
U1002 Lost Communication with Gateway Module After the power switch is turned on (IG), communication between the millimeter wave radar sensor assembly and forward recognition camera is abnormal for 2 seconds or more.
·

CAN bus line or connector

·

Forward recognition camera

·

Millimeter wave radar sensor assembly



WIRING DIAGRAM

B472644E01
3.51,1.667 4.906,2.083 1.396,0.417 10 false Millimeter Wave Radar Sensor Assembly 3.51,1.5 3.969,1.698 0.458,0.198 10 false A30 5.75,1.656 7,2.031 1.25,0.375 10 false Forward Recognition Camera 5.75,1.5 6.208,1.698 0.458,0.198 10 false V6 4.5,0.417 5.115,0.615 0.615,0.198 10 false CA1P 4.5,1.177 5.115,1.375 0.615,0.198 10 false CA1N 6.021,0.406 6.635,0.604 0.615,0.198 10 false CANH 6.031,1.188 6.646,1.385 0.615,0.198 10 false CANL 4.948,0.417 5.104,0.615 0.156,0.198 10 false 5 4.948,1.177 5.104,1.375 0.156,0.198 10 false 6 5.771,1.188 6.042,1.417 0.271,0.229 10 false 12 5.844,0.417 6,0.615 0.156,0.198 10 false 6 3.625,1.073 4.24,1.271 0.615,0.198 10 false SGND 3.625,0.521 4.24,0.719 0.615,0.198 10 false IGB 3.448,0.417 3.604,0.615 0.156,0.198 10 false 8 3.448,0.948 3.604,1.146 0.156,0.198 10 false 1 2.344,0.677 3.719,0.875 1.375,0.198 10 false ECU-IG1 NO. 3 0.354,0.531 3.417,0.729 3.063,0.198 10 false from IG1-NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the millimeter wave radar sensor assembly has been replaced, be sure to perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK CAN BUS LINE (MALFUNCTION CONFIRMATION)
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.
B472643C01
1.406,0.313 1.813,0.573 0.406,0.26 1.958,1.896 2.656,1.969 true 1.031,2.448 1.333,2.115 true 1.927,2.115 2.344,2.417 true 1.729,2.125 2.083,2.646 true 0.76,2.396 1.219,2.594 0.458,0.198 10 false IGB 2.698,1.896 3.156,2.094 0.458,0.198 10 false SGND 2.385,2.354 2.844,2.552 0.458,0.198 10 false CA1P 2.125,2.625 2.583,2.823 0.458,0.198 10 false CA1N 1.49,0.365 1.948,0.563 0.458,0.198 10 false A30 0.156,0.198 0.469,0.354 0.313,0.156 10 false *a
*a Component with harness connected
(Millimeter Wave Radar Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
A30-5 (CA1P) - A30-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω:
Short circuit between CAN bus lines
70 Ω or more:
Open circuit in a CAN bus line
A30-5 (CA1P) - A30-1 (SGND) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω:
Ground short
A30-6 (CA1N) - A30-1 (SGND) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω:
Ground short
A30-5 (CA1P) - A30-8 (IGB) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ:
+B short
A30-6 (CA1N) - A30-8 (IGB) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ:
+B short



Result:
Result Proceed to
OK A
NG (Open circuit in CAN bus line) B
NG (Short circuit between CAN bus lines) C
NG (Short to +B or ground) D



A

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)

B

3.CHECK FOR OPEN IN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - FORWARD RECOGNITION CAMERA)

C

5.CHECK FOR SHORT BETWEEN CAN BUS LINES (FORWARD RECOGNITION CAMERA)

D

7.CHECK FOR SHORT IN CAN BUS LINE (FORWARD RECOGNITION CAMERA)
2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the power switch on (IG) and wait 2 seconds or more.




c.

Check for DTCs.

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U1002 is not output A
DTC U1002 is output B



A

B

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

3.CHECK FOR OPEN IN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - FORWARD RECOGNITION CAMERA)
a.

Disconnect the V6 forward recognition camera connector.


b.

Disconnect the A30 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-6 (CANH) - A30-5 (CA1P) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
V6-12 (CANL) - A30-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



d.

Connect the A30 millimeter wave radar sensor assembly connector.


e.

Connect the V6 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

4.CHECK FOR OPEN IN CAN BUS LINES (FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE CAN BUS LINE OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - FORWARD RECOGNITION CAMERA)

4.CHECK FOR OPEN IN CAN BUS LINES (FORWARD RECOGNITION CAMERA)
a.
A380142C63
1.531,0.177 1.896,0.448 0.365,0.271 2.146,1.115 2.458,0.979 true 2.146,1.438 2.448,1.521 true 0.125,0.125 0.438,0.281 0.313,0.156 10 false *a 1.635,0.24 2.01,0.448 0.375,0.208 10 false V6 2.49,0.896 3.104,1.094 0.615,0.198 10 false CANH 2.5,1.448 3.115,1.646 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the V6 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-6 (CANH) - V6-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



c.

Connect the V6 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

5.CHECK FOR SHORT BETWEEN CAN BUS LINES (FORWARD RECOGNITION CAMERA)
a.
A380142C63
1.531,0.177 1.896,0.448 0.365,0.271 2.146,1.115 2.458,0.979 true 2.146,1.438 2.448,1.521 true 0.125,0.125 0.438,0.281 0.313,0.156 10 false *a 1.635,0.24 2.01,0.448 0.375,0.208 10 false V6 2.49,0.896 3.104,1.094 0.615,0.198 10 false CANH 2.5,1.448 3.115,1.646 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the V6 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-6 (CANH) - V6-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



c.

Connect the V6 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

6.CHECK FOR SHORT BETWEEN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
6.CHECK FOR SHORT BETWEEN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.
A380144C28
1.479,0.167 1.875,0.406 0.396,0.24 1.313,1.792 1.448,1.26 true 1.615,1.26 1.823,1.792 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.563,0.198 1.938,0.427 0.375,0.229 10 false A30 1.146,1.813 1.76,2.01 0.615,0.198 10 false CA1P 1.688,1.813 2.302,2.01 0.615,0.198 10 false CA1N
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A30 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-5 (CA1P) - A30-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



c.

Connect the A30 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS LINE OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - FORWARD RECOGNITION CAMERA)

7.CHECK FOR SHORT IN CAN BUS LINE (FORWARD RECOGNITION CAMERA)
a.

Disconnect the V6 forward recognition camera connector.

B427441C34
1.74,0.542 2.135,0.781 0.396,0.24 4.875,0.417 5.365,0.667 0.49,0.25 2.354,1.427 2.729,1.281 true 2.344,1.74 2.719,1.865 true 4.625,0.698 4.99,1.104 true 5.802,1.698 6.125,1.927 true 4.063,0.208 4.375,0.365 0.313,0.156 10 false *1 1.302,0.198 1.615,0.354 0.313,0.156 10 false *a 1.854,0.573 2.313,0.771 0.458,0.198 10 false V6 4.958,0.458 5.417,0.656 0.458,0.198 10 false K154 2.781,1.208 3.396,1.406 0.615,0.198 10 false CANH 2.781,1.802 3.396,2 0.615,0.198 10 false CANL 4.385,0.625 4.719,0.823 0.333,0.198 10 false CG 6.177,1.875 6.51,2.073 0.333,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Forward Recognition Camera)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-6 (CANH) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V6-12 (CANL) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V6-6 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
V6-12 (CANL) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



c.

Connect the V6 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

8.CHECK FOR SHORT IN CAN BUS LINE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
8.CHECK FOR SHORT IN CAN BUS LINE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the A30 millimeter wave radar sensor assembly connector.

B427442C34
1.833,0.385 2.219,0.604 0.385,0.219 4.969,0.385 5.427,0.646 0.458,0.26 1.344,1.885 1.771,1.573 true 2,1.563 2.188,2.094 true 4.552,0.656 5.094,1.115 true 5.896,1.708 6.198,1.958 true 4.115,0.177 4.427,0.333 0.313,0.156 10 false *1 1.292,0.188 1.604,0.344 0.313,0.156 10 false *a 1.906,0.417 2.365,0.615 0.458,0.198 10 false A30 5.042,0.427 5.5,0.625 0.458,0.198 10 false K154 4.313,0.594 4.625,0.792 0.313,0.198 10 false CG 6.25,1.906 6.708,2.104 0.458,0.198 10 false BAT 0.969,1.844 1.427,2.042 0.458,0.198 10 false CA1P 2.042,2.125 2.5,2.323 0.458,0.198 10 false CA1N
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-5 (CA1P) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A30-6 (CA1N) - K154-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A30-5 (CA1P) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A30-6 (CA1N) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



c.

Connect the A30 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS LINE OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - FORWARD RECOGNITION CAMERA)