Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › 2019.02–2021.02
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0383394 ROAD SIGN ASSIST SYSTEM U

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  TERMINALS OF ECU  


CHECK FORWARD RECOGNITION CAMERA


B472992E01
2.073,0.833 2.458,1.042 0.385,0.208 2.188,0.865 2.5,1.063 0.313,0.198 10 false V6

NOTICE:
·

DTCs may be stored when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the V6 forward recognition camera connector.



a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V6-7 (IGB) - V6-10 (GND) LA-P - LA Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
V6-10 (GND) - Body ground LA - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, malfunction of a CAN bus line, terminating resistor or the forward recognition camera is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V6-5 (CA1P) - V6-10 (GND) L - LA CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
V6-11 (CA1N) - V6-10 (GND) W - LA CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
V6-6 (CANH) - V6-10 (GND) G - LA CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
V6-12 (CANL) - V6-10 (GND) W - LA CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)

i.
A438764N01
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.396,1.906 2.344,2.094 0.948,0.188 10 false 10 μs./DIV. 3.031,1.406 3.344,1.698 0.313,0.292 10 false GND

Waveform 1

Item Content
Tester Connection
·

Between V6-5 (CA1P) and V6-10 (GND)

·

Between V6-6 (CANH) and V6-10 (GND)


Tool Setting 1 V/DIV., 10 μs./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A438765N01
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.406,1.875 2.375,2.073 0.969,0.198 10 false 10 μs./DIV. 3.031,1.375 3.406,1.625 0.375,0.25 10 false GND

Waveform 2

Item Content
Tester Connection
·

Between V6-11 (CA1N) and V6-10 (GND)

·

Between V6-12 (CANL) and V6-10 (GND)


Tool Setting 1 V/DIV., 10 μs./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.