Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2019.02
RM33C0E _58 Vehicle Interior _065456 THEFT DETERRENT / KEYLESS ENTRY _0385172 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Touching Unlock Sensor for Certain Period of Time does not Unlock All Doors  


DESCRIPTION

If the entry unlock function of the driver door cannot be operated by touching and holding the unlock sensor of the driver door, but can be operated through other methods, it can be determined that the request code is being transmitted properly from the driver door. In this case, the certification ECU (smart key ECU assembly) may be malfunctioning.

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.



HINT:

Touching the unlock sensor for a certain period of time to unlock all of the doors can only be performed if the customize setting "Door Unlock Mode2" is set to "Driver".


PROCEDURE

1.CHECK CUSTOMIZE SETTING (DOOR UNLOCK SENSOR TOUCH TIME ADJUST)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Customize Setting / Entry & Start.

Entry & Start
Tester Display Description Default Setting ECU
Door Unlock Sensor Touch Time Adjust Function that sets the length of time the unlock sensor on the door outside handle assembly (for driver door) must be touched to unlock all of the doors OFF*1
Middle*2
00:OFF,01:Short,10:Middle,11:Long Certification ECU (Smart key ECU assembly)
50006 17

*1: w/o Canister Pump Module

*2: w/ Canister Pump Module



Result:
Result Proceed to
The customize setting is set to Short, Middle or Long A
The customize setting is set to OFF B



A

2.CHECK ENTRY UNLOCK FUNCTION (OPERATION CHECK)

B

2.CHECK ENTRY UNLOCK FUNCTION (OPERATION CHECK)
a.

Turn the power switch off.


b.

Open and close the driver door.


c.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


d.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


e.

Check that the LED of the electrical key transmitter sub-assembly blinks.


f.
for LHD:
B486120C01
0.896,0.792 1.104,0.792 1.104,0.792 1.708,1.51 false 0.698,0.698 1.01,0.896 0.313,0.198 10 false *a
*a Unlock Sensor (Backside)


for RHD:
B484646C02
1.667,1.479 2.333,0.979 2.333,0.979 2.583,0.979 false 2.625,0.896 2.938,1.094 0.313,0.198 10 false *a
*a Unlock Sensor (Backside)


Touch and hold the unlock sensor on the door outside handle assembly (for driver door) for 2.5 seconds or more.

HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).



g.

Check that all of the doors unlock.


Result:
Result Proceed to
All of the doors do not unlock A
Any door does not unlock B



A

3.CHECK POWER DOOR LOCK CONTROL SYSTEM

B

3.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
The door locks operate normally A
The door locks do not operate normally B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B