Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2019.02–2021.02
RM33C0E _56 Audio / Visual / Telematics _078700 TELEMATICS _0387130 TELEMATICS SYSTEM(for eCall) D

TELEMATICS  TELEMATICS SYSTEM(for eCall)  SYSTEM DESCRIPTION  


DESCRIPTION


a.

eCall provides 2 services: Automatic Emergency Call and Manual Emergency Call.

If the vehicle is involved in an accident, the telematics system will make an automatic emergency call to a Public Safety Answering Point (PSAP) and transmit the vehicle location, determined by a GNSS satellite, and vehicle information. After receiving an emergency call from the vehicle, depending on the situation, a PSAP operator may immediately contact emergency services.

Y178726C01
4.802,5.906 5.115,6.104 0.313,0.198 10 false *a 3.271,3.927 3.583,4.125 0.313,0.198 10 false *b 5.635,4.438 5.948,4.635 0.313,0.198 10 false *c 5.344,1.448 5.656,1.646 0.313,0.198 10 false *c 6.719,3.677 7.031,3.875 0.313,0.198 10 false *d 3.906,1.729 4.219,1.927 0.313,0.198 10 false *e 0.458,2.375 0.771,2.573 0.313,0.198 10 false *f 1.271,3.052 1.583,3.25 0.313,0.198 10 false *g 2.354,1.229 2.667,1.427 0.313,0.198 10 false *c 0.646,4.844 0.958,5.042 0.313,0.198 10 false *h 2.198,4.948 2.51,5.146 0.313,0.198 10 false *i 0.344,6.333 0.656,6.531 0.313,0.198 10 false *j
*a Emergency Call Service *b GNSS Satellite
*c Cellular Phone Line *d Cellular Phone Base Station
*e Mobile Network Operator (MNO) or Mobile Virtual Network Operator (MVNO) *f Public Safety Answering Point (PSAP)
*g Public Fixed Line *h Emergency Vehicle
*i Public safety authorities such a police or fire department *j The illustrations shown are examples only and may differ from the actual service.




FUNCTION OF MAIN COMPONENTS


Component Function
Roof Console Box Sub-assembly
·

Manual (SOS) Switch


Sends a switch signal to the telematics transceiver when pressed. (When a test call or manual emergency call is performed.)
LED Indicator Light Green
·

Depending on the DCM activation mode type, illuminates or turns off immediately after the power switch is turned on (IG).

·

Turns on when the system is operating normally.

·

Blinks during a call and turns off when the system is malfunctioning.

·

Blinks during test mode.

·

Blinks 5 times when entering test mode (the manual (SOS) switch indicator (red) blinks at the same time).


Red
·

Depending on the DCM activation mode type, illuminates or turns off immediately after the power switch is turned on (IG).

·

Blinks when an emergency call cannot be performed.

·

Turns off when the system is operating normally.

·

Illuminates when the mobilephone battery needs to be replaced.

·

Illuminates in diagnostic mode to indicate a DTC.

·

Blinks 5 times when entering test mode (the manual (SOS) switch indicator (green) blinks at the same time).


Communication Telematics Box
·

Sends the microphone voice signal to the telematics transceiver.

·

Outputs sound signals received from the telematics transceiver through a built-in speaker.

·

Checks for malfunctions in its built-in speaker and microphone when the power switch is turned on (IG).

·

Checks for an open in the speaker and microphone circuits between it and the telematics transceiver when the power switch is on (IG).


Roof Antenna Assembly
·

Sends and receives data and voice signals used for emergency calls via a communication network.

·

Receives GPS and GNSS radio signals and sends them to the telematics transceiver.


Telematics Transceiver
·

Uses the roof antenna assembly to send and receive data and voice signals used for emergency calls via a communication network.

-

Sends the received voice signal to the communication telematics box.

-

Receives the sent voice signal from the communication telematics box.

-

Sends a mute signal to the radio and display receiver assembly*1 or stereo component amplifier assembly*2. (The audio system is automatically muted during an emergency call.)

-

Sends vehicle location information to the PSAP.

-

Conducts self-diagnosis every time the power switch is turned on (IG) and after an automatic emergency call or manual emergency call is made.



Mobilephone Battery
·

When an automatic emergency call is performed, provides power to the telematics transceiver.

·

When a manual emergency call is made, is not used as the power source.


Airbag Sensor Assembly Sends a collision signal to the telematics transceiver. (An automatic emergency call is made.)

*1: for 6 Speakers

*2: for 9 Speakers



DCM ACTIVATION STATUS


After the power switch is turned on (IG), there are 3 types of manual (SOS) switch indicator illumination patterns. Depending on the illumination pattern, it is possible to determine the current status of the DCM activation.

Indicator illumination pattern
E438300E02
4.656,2.469 4.479,2.469 4.479,2.469 4.219,2.927 true 5.948,1.083 6.094,0.854 true 6.74,1.073 6.604,0.854 true 5.771,1.104 6.229,1.302 0.458,0.198 10 false Red 6.573,1.104 7.156,1.292 0.583,0.188 10 false Green 0.177,0.729 1.156,0.927 0.979,0.198 10 false Shipping Mode 0.094,1.875 1.292,2.083 1.198,0.208 10 false eCall Only Mode 0.417,2.99 1.615,3.198 1.198,0.208 10 false Live Mode 3.521,0.208 4.5,0.406 0.979,0.198 10 false Green: 2s 2.229,0.198 3.208,0.396 0.979,0.198 10 false Red: 10s 3.5,2.417 4.479,2.615 0.979,0.198 10 false Green: 2s 2.229,1.344 3.208,1.542 0.979,0.198 10 false Red: 10s 3.5,1.344 4.479,1.542 0.979,0.198 10 false Green: 2s 2.24,2.438 3.219,2.635 0.979,0.198 10 false Red: 10s 4.729,2.385 5.969,2.583 1.24,0.198 10 false Red & Green: 1s 0.583,0.177 1.969,0.375 1.385,0.198 10 false Power Switch On (IG) 0.583,1.292 1.958,1.5 1.375,0.208 10 false Power Switch On (IG) 0.594,2.417 2,2.604 1.406,0.188 10 false Power Switch On (IG)

HINT:

For some destinations, only eCall Only Mode is available.



MAYDAY ID OUTLINE


a.

The telematics transceiver functions as the emergency call service device to perform emergency calls.


b.

The telematics transceiver has serial numbers (IMEI, ICCID) which can be used to identify the individual device when servicing.


c.
E338334C01
2.563,1.896 2.729,1.896 2.729,1.896 2.729,0.979 false 2.396,1.802 2.708,2 0.313,0.198 10 false *a
*a IMEI, ICCID


The IMEI and ICCID are printed on the label attached to the telematics transceiver.



COMMUNICATION SYSTEM


a.

CAN Communication Outline

i.

The telematics system uses CAN communication between the telematics transceiver and ECUs.




DIAGNOSTIC FUNCTION OUTLINE


a.

The telematics system has a diagnostic function (the result will be displayed on the GTS).