Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM › 2019.02–2021.02
RM33C0E _56 Audio / Visual / Telematics _065452 PARK ASSIST / MONITORING _0387691 PARKING SUPPORT BRAKE SYSTEM C

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the clearance warning ECU assembly receives a signal via CAN communication from the steering sensor that indicates a power supply problem.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering sensor power source
·

Harness or connector

·

Steering sensor



WIRING DIAGRAM

E309568E13
5.677,1.854 6.875,2.375 1.198,0.521 10 false Clearance Warning ECU Assembly 4.844,1.302 5,1.5 0.156,0.198 10 false 6 4.448,1.385 4.906,1.583 0.458,0.198 10 false ESS 3.906,0.667 4.365,0.865 0.458,0.198 10 false IG 3.917,1.344 4.375,1.542 0.458,0.198 10 false BAT 3.833,1.833 4.292,2.031 0.458,0.198 10 false K71 3.813,1.99 5.563,2.573 1.75,0.583 10 false Steering Sensor 3.719,0.573 3.875,0.771 0.156,0.198 10 false 9 3.708,1.24 3.865,1.438 0.156,0.198 10 false 4 2.438,0.833 4.271,1.031 1.833,0.198 10 false ECU-IG1 NO. 2 2.427,1.5 4.115,1.698 1.688,0.198 10 false ECU-DCC NO. 1 0.26,1.323 1.823,1.563 1.563,0.24 10 false from Auxiliary Battery 0.24,0.667 1.708,1 1.469,0.333 10 false from IG1-NO. 1 Relay 0.917,3.188 3.094,3.417 2.177,0.229 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After replacing an ultrasonic sensor or the clearance warning ECU assembly, perform the necessary procedures (adjustment, calibration, initialization or registration).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE)
a.

Disconnect the K71 steering sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K71-9 (IG) - K71-6 (ESS) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (STEERING SENSOR POWER SOURCE)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K71-6 (ESS) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K71-4 (BAT) - K71-6 (ESS) Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR