Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT › 2019.02–2020.08
RM33C0E _53 Suspension _065437 ALIGNMENT / HANDLING DIAGNOSIS _0327991 FRONT WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  FRONT WHEEL ALIGNMENT  ADJUSTMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the front wheel alignment procedure are shown below.

Necessary Procedures After Procedure Performed
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

PROCEDURE

Hide 1. PRECAUTION

As the standard wheel alignment values differ depending on the suspension type, refer to the following table to confirm the suspension type for each model.

Model Code Suspension Type

*: for Rough Road Area Specification Vehicles

AXVH71R-AEXDBQ NORMAL
AXVH71L-AEXDBV NORMAL
AXVH71L-AEXNBW NORMAL
AXVH71L-AEXDBR NORMAL
AXVH71L-AEXDBW SPORT
AXVH71R-AEXDBW SPORT
AXVH71L-AEXNBW* NORMAL
AXVH71R-AEXNBW* NORMAL

Hide 3.MEASURE VEHICLE HEIGHT

NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C370166N01
0.844,1.125 1,1.323 0.156,0.198 10 false A 2.406,1.198 2.563,1.396 0.156,0.198 10 false B 0.813,3.99 0.969,4.188 0.156,0.198 10 false C 2.375,4.031 2.531,4.229 0.156,0.198 10 false D

Measure the vehicle height.

Measurement Points:

A: Ground clearance of front wheel center


B: Ground clearance of center of bolt head of front lower No. 2 suspension arm bushing (rear bolt of front lower No. 1 suspension arm sub-assembly).


C: Ground clearance of rear wheel center


D: Ground clearance of center of bolt head of rear No. 2 suspension arm assembly and rear suspension member sub-assembly.


Vehicle Height (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Front A - B Rear C - D
NORMAL 205/65R16 147 mm (5.79 in.) 47 mm (1.85 in.)
215/55R17 147 mm (5.79 in.) 47 mm (1.85 in.)
235/45R18 147 mm (5.79 in.) 47 mm (1.85 in.)
SPORT 215/55R17 148 mm (5.83 in.) 52 mm (2.05 in.)
235/45R18 148 mm (5.83 in.) 52 mm (2.05 in.)


Vehicle Height (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Front A - B Rear C - D
NORMAL 215/55R17 134 mm (5.28 in.) 39 mm (1.54 in.)
235/45R18 134 mm (5.28 in.) 39 mm (1.54 in.)



Hide 4.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440C16
2.396,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.604,0.708 1.031,0.708 1.031,0.708 1.031,1.458 false 2.76,0.729 2.99,0.906 0.229,0.177 10 false *b 0.448,0.604 0.688,0.781 0.24,0.177 10 false *a
*a Turning Radius Gauge
*b Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.


b.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Camber Inclination Right-left Difference
NORMAL 205/65R16 -0°30' +/- 0°45' (-0.50° +/- 0.75°) 0°45' (0.75°) or less
215/55R17 -0°30' +/- 0°45' (-0.50° +/- 0.75°)
235/45R18 -0°30' +/- 0°45' (-0.50° +/- 0.75°)
SPORT 215/55R17 -0°30' +/- 0°45' (-0.50° +/- 0.75°)
235/45R18 -0°30' +/- 0°45' (-0.50° +/- 0.75°)


Camber (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Camber Inclination Right-left Difference
NORMAL 215/55R17 -0°20' +/- 0°45' (-0.33° +/- 0.75°) 0°45' (0.75°) or less
235/45R18 -0°20' +/- 0°45' (-0.33° +/- 0.75°)


Caster (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Caster Inclination Right-left Difference
NORMAL 205/65R16 5°20' +/- 0°45' (5.33° +/- 0.75°) 0°45' (0.75°) or less
215/55R17 5°20' +/- 0°45' (5.33° +/- 0.75°)
235/45R18 5°20' +/- 0°45' (5.33° +/- 0.75°)
SPORT 215/55R17 5°25' +/- 0°45' (5.42° +/- 0.75°)
235/45R18 5°25' +/- 0°45' (5.42° +/- 0.75°)


Caster (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Caster Inclination Right-left Difference
NORMAL 215/55R17 5°20' +/- 0°45' (5.33° +/- 0.75°) 0°45' (0.75°) or less
235/45R18 5°20' +/- 0°45' (5.33° +/- 0.75°)


Steering Axis Inclination (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Steering Axis Inclination Reference
NORMAL 205/65R16 12°50' (12.83°)
215/55R17 12°50' (12.83°)
235/45R18 12°50' (12.83°)
SPORT 215/55R17 12°50' (12.83°)
235/45R18 12°50' (12.83°)


Steering Axis Inclination (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Steering Axis Inclination Reference
NORMAL 215/55R17 12°30' (12.50°)
235/45R18 12°30' (12.50°)



Hide 5.ADJUST CAMBER

NOTICE:

Inspect toe-in after the camber has been adjusted.


a.

Remove the front wheel.

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>REMOVAL


b.
C370167

Remove the 2 nuts on the lower side of the front shock absorber assembly.

NOTICE:

Keep the bolts inserted.



c.

Remove the top and bottom bolts one at a time and confirm that the steering knuckle can move freely in the front shock absorber assembly.

HINT:
·

Reinstall each bolt after removing it and confirming steering knuckle movement.

·

If the steering knuckle does not move freely in the front shock absorber assembly, clean the contact surfaces of the front shock absorber assembly and the steering knuckle.




d.

Temporarily install the 2 nuts. (Step A)


e.
C199624N01
1.01,0.125 1.167,0.323 0.156,0.198 10 - 1.875,0.052 2.031,0.25 0.156,0.198 10 +

Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)


f.
C370167

Tighten the 2 nuts.

Torque:
290 N*m (2957 kgf*cm, 214 ft.*lbf)

NOTICE:

Keep the bolts from rotating when tightening the nuts.



g.

Install the front wheel.

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>INSTALLATION


h.

Bounce the vehicle up and down at the corners to stabilize the suspension.


i.

Check the camber.

Camber (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Camber Inclination Right-left Difference
NORMAL 205/65R16 -0°30' +/- 0°45' (-0.50° +/- 0.75°) 0°45' (0.75°) or less
215/55R17 -0°30' +/- 0°45' (-0.50° +/- 0.75°)
235/45R18 -0°30' +/- 0°45' (-0.50° +/- 0.75°)
SPORT 215/55R17 -0°30' +/- 0°45' (-0.50° +/- 0.75°)
235/45R18 -0°30' +/- 0°45' (-0.50° +/- 0.75°)


Camber (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Camber Inclination Right-left Difference
NORMAL 215/55R17 -0°20' +/- 0°45' (-0.33° +/- 0.75°) 0°45' (0.75°) or less
235/45R18 -0°20' +/- 0°45' (-0.33° +/- 0.75°)


i.
C241271N01
0.354,1.125 0.563,1.125 false 0.344,1.417 0.521,1.417 false 0.208,1.021 0.365,1.219 0.156,0.198 10 false 1 0.208,1.344 0.365,1.542 0.156,0.198 10 false 2

If the measured value is not within the specification, calculate the required adjustment amount using the formula below.

Camber adjustment amount = center of the specified range - measured value

Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.

HINT:

Try to adjust the camber to the center of the specified values.


To move the axle hub toward (+) in step B To move the axle hub toward (-) in step B
Refer to table (1) (To move the axle hub toward the positive side) Refer to table (2) (To move the axle hub toward the negative side)

The vehicle body and suspension may be damaged if the camber cannot be correctly adjusted according to the table above.

NOTICE:

Replace the nut with a new one when replacing the bolt.



ii.

Table (1) (To move the axle hub toward the positive side)

C212217C01
2.052,0.531 2.188,0.74 0.135,0.208 10 1 2.052,1.146 2.188,1.354 0.135,0.208 10 2 2.521,0.792 2.75,0.99 0.229,0.198 10 *c 3.219,1.406 3.448,1.594 0.229,0.188 10 *d 5.979,0.792 6.198,0.99 0.219,0.198 10 *e 5.271,0.792 5.521,0.99 0.25,0.198 10 *d 4.604,1.406 4.781,1.583 0.177,0.177 10 *f 3.917,1.406 4.125,1.615 0.208,0.208 10 *e 4.396,6.375 4.583,6.552 0.188,0.177 10 *f 5.969,1.396 6.177,1.552 0.208,0.156 10 *f 5.271,1.406 5.469,1.583 0.198,0.177 10 *f 6.656,1.396 6.833,1.552 0.177,0.156 10 *f 6.646,0.792 6.854,0.969 0.208,0.177 10 *f 2.542,2.99 2.719,3.219 0.177,0.229 10 A 2.542,4.188 2.771,4.406 0.229,0.219 10 F 2.542,3.469 2.771,3.688 0.229,0.219 10 C 2.542,3.938 2.74,4.156 0.198,0.219 10 E 2.542,3.24 2.729,3.448 0.188,0.208 10 B 2.542,3.708 2.729,3.927 0.188,0.219 10 D 3.927,3.01 4.177,3.24 0.25,0.229 10 C 5.271,3 5.51,3.229 0.24,0.229 10 E 3.229,3.01 3.406,3.219 0.177,0.208 10 B 4.604,3 4.792,3.24 0.188,0.24 10 D 3.229,2.76 3.448,2.99 0.219,0.229 10 G 3.229,3.24 3.406,3.448 0.177,0.208 10 C 3.229,3.708 3.448,3.938 0.219,0.229 10 E 3.229,3.469 3.427,3.698 0.198,0.229 10 D 3.229,3.938 3.427,4.167 0.198,0.229 10 F 3.927,2.51 4.115,2.74 0.188,0.229 10 G 3.927,2.76 4.135,2.969 0.208,0.208 10 A 3.927,3.708 4.115,3.938 0.188,0.229 10 F 3.917,3.469 4.083,3.688 0.167,0.219 10 E 3.927,3.24 4.135,3.458 0.208,0.219 10 D 4.604,2.281 4.802,2.531 0.198,0.25 10 G 6.656,1.563 6.833,1.823 0.177,0.26 10 G 5.979,1.813 6.26,2.063 0.281,0.25 10 G 5.271,2.031 5.458,2.281 0.188,0.25 10 G 6.656,1.813 6.813,2.042 0.156,0.229 10 A 6.656,2.281 6.844,2.531 0.188,0.25 10 C 6.656,2.76 6.885,3.01 0.229,0.25 10 E 6.656,2.031 6.833,2.26 0.177,0.229 10 B 6.656,2.51 6.875,2.781 0.219,0.271 10 D 5.979,2.031 6.177,2.292 0.198,0.26 10 A 5.979,2.51 6.188,2.75 0.208,0.24 10 C 5.979,2.281 6.26,2.531 0.281,0.25 10 B 5.979,2.76 6.167,2.99 0.188,0.229 10 D 5.979,3 6.115,3.208 0.135,0.208 10 F 5.271,3.24 5.49,3.448 0.219,0.208 10 F 5.271,2.281 5.406,2.51 0.135,0.229 10 A 5.271,2.76 5.448,2.969 0.177,0.208 10 C 5.271,2.51 5.438,2.74 0.167,0.229 10 B 4.604,2.51 4.781,2.76 0.177,0.25 10 A 4.604,2.76 4.781,2.969 0.177,0.208 10 B 4.604,3.24 4.813,3.458 0.208,0.219 10 E 4.604,3.469 4.813,3.698 0.208,0.229 10 F 1.625,5.073 1.76,5.281 0.135,0.208 10 A 5.094,5.073 5.229,5.281 0.135,0.208 10 F 3.052,5.073 3.188,5.281 0.135,0.208 10 C 4.406,5.073 4.542,5.281 0.135,0.208 10 E 2.344,5.073 2.479,5.281 0.135,0.208 10 B 3.729,5.073 3.865,5.281 0.135,0.208 10 D 5.802,5.073 5.938,5.281 0.135,0.208 10 G 1.073,5.5 1.208,5.708 0.135,0.208 10 1 1.104,6.135 1.24,6.344 0.135,0.208 10 2 3.042,6.375 3.229,6.531 0.188,0.156 10 *f 3.719,6.375 3.958,6.542 0.24,0.167 10 *f 5.083,6.375 5.292,6.573 0.208,0.198 10 *f 5.094,5.75 5.292,5.917 0.198,0.167 10 *f 4.385,5.75 4.604,5.917 0.219,0.167 10 *e 2.333,6.375 2.542,6.542 0.208,0.167 10 *e 1.625,6.375 1.854,6.552 0.229,0.177 10 *d 3.719,5.75 3.927,5.938 0.208,0.188 10 *d 3.01,5.75 3.208,5.938 0.198,0.188 10 *c 1.625,5.75 1.844,5.948 0.219,0.198 10 *c 2.333,5.75 2.521,5.906 0.188,0.156 10 *c 5.802,6.365 6.021,6.563 0.219,0.198 10 *c 5.76,5.76 5.969,5.948 0.208,0.188 10 *c 0.177,1.563 2.198,1.75 2.021,0.188 10 -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 -0°15' to 0° (-0.25° to 0°) 0.208,2.51 2.156,2.729 1.948,0.219 10 -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 1°15' to 1°30' (1.25° to 1.5°) 2.542,1.406 2.76,1.604 0.219,0.198 10 *c 3.219,0.792 3.448,0.969 0.229,0.177 10 *c 3.917,0.792 4.135,1.01 0.219,0.219 10 *c 4.604,0.792 4.823,1.01 0.219,0.219 10 *c 5.979,3 6.24,3.24 0.26,0.24 10 F 1.156,0.625 1.333,0.792 0.177,0.167 10 *a 0.625,1.115 0.802,1.281 0.177,0.167 10 *b 0.875,4.792 1.198,5.021 0.323,0.229 12 *B 0.063,0.135 0.333,0.333 0.271,0.198 12 *A
*A Table (1) (To move the axle hub toward the positive side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c Standard Bolt *d 90105-17013
*e 90105-17014 *f 90105-17015



iii.

Table (2) (To move the axle hub toward the negative side)

C212218C01
2.052,0.531 2.188,0.74 0.135,0.208 10 1 2.052,1.146 2.188,1.354 0.135,0.208 10 2 1.635,5.052 1.771,5.26 0.135,0.208 10 A 5.094,5.052 5.229,5.26 0.135,0.208 10 F 3.052,5.052 3.188,5.26 0.135,0.208 10 C 4.406,5.052 4.542,5.26 0.135,0.208 10 E 2.344,5.052 2.479,5.26 0.135,0.208 10 B 3.729,5.052 3.865,5.26 0.135,0.208 10 D 5.802,5.052 5.938,5.26 0.135,0.208 10 G 1.073,5.5 1.208,5.708 0.135,0.208 10 1 1.104,6.135 1.24,6.344 0.135,0.208 10 2 0.177,1.563 2.198,1.75 2.021,0.188 10 -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 -0°15' to 0° (-0.25° to 0°) 0.208,2.521 2.156,2.74 1.948,0.219 10 -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 1°15' to 1°30' (1.25° to 1.5°) 1.156,0.625 1.333,0.792 0.177,0.167 10 *a 0.625,1.115 0.802,1.281 0.177,0.167 10 *b 0.875,4.792 1.167,5.021 0.292,0.229 12 *B 0.063,0.135 0.417,0.354 0.354,0.219 12 *A 5.292,2.76 5.427,2.969 0.135,0.208 10 E 5.292,3.708 5.427,3.917 0.135,0.208 10 G 5.292,2.521 5.427,2.729 0.135,0.208 10 F 5.292,3.469 5.427,3.677 0.135,0.208 10 A 5.292,3 5.427,3.208 0.135,0.208 10 C 5.292,3.24 5.427,3.448 0.135,0.208 10 B 2.542,2.76 2.677,2.969 0.135,0.208 10 A 2.542,1.563 2.677,1.771 0.135,0.208 10 F 2.542,2.281 2.677,2.49 0.135,0.208 10 C 2.542,1.813 2.677,2.021 0.135,0.208 10 E 2.542,2.521 2.677,2.729 0.135,0.208 10 B 2.542,2.031 2.677,2.24 0.135,0.208 10 D 3.229,2.76 3.365,2.969 0.135,0.208 10 B 3.229,3 3.365,3.208 0.135,0.208 10 G 3.229,2.521 3.365,2.729 0.135,0.208 10 C 3.229,2.031 3.365,2.24 0.135,0.208 10 E 3.229,2.281 3.365,2.49 0.135,0.208 10 D 3.229,1.813 3.375,2.021 0.146,0.208 10 F 3.927,2.76 4.063,2.969 0.135,0.208 10 C 3.927,3.24 4.063,3.448 0.135,0.208 10 G 3.927,3 4.063,3.208 0.135,0.208 10 A 3.927,2.031 4.063,2.24 0.135,0.208 10 F 3.927,2.281 4.063,2.49 0.135,0.208 10 E 3.927,2.521 4.063,2.729 0.135,0.208 10 D 4.604,2.76 4.74,2.969 0.135,0.208 10 D 4.604,3.469 4.74,3.677 0.135,0.208 10 G 4.604,3.24 4.74,3.448 0.135,0.208 10 A 4.604,3 4.74,3.208 0.135,0.208 10 B 4.604,2.521 4.74,2.729 0.135,0.208 10 E 4.604,2.281 4.74,2.49 0.135,0.208 10 F 5.99,3.938 6.125,4.146 0.135,0.208 10 G 5.99,3.708 6.125,3.917 0.135,0.208 10 A 5.99,3.24 6.125,3.448 0.135,0.208 10 C 5.99,3.469 6.125,3.677 0.135,0.208 10 B 5.99,3 6.125,3.208 0.135,0.208 10 D 5.99,2.76 6.125,2.969 0.135,0.208 10 F 6.688,4.188 6.823,4.396 0.135,0.208 10 G 6.688,3.938 6.823,4.146 0.135,0.208 10 A 6.688,3.469 6.823,3.677 0.135,0.208 10 C 6.688,3 6.823,3.208 0.135,0.208 10 E 6.688,3.708 6.823,3.917 0.135,0.208 10 B 6.688,3.24 6.823,3.448 0.135,0.208 10 D 2.51,0.792 2.729,0.969 0.219,0.177 10 *c 3.219,1.396 3.406,1.573 0.188,0.177 10 *d 5.969,0.781 6.115,0.938 0.146,0.156 10 *e 5.271,0.792 5.469,0.979 0.198,0.188 10 *d 4.604,1.396 4.781,1.573 0.177,0.177 10 *f 3.906,1.396 4.083,1.573 0.177,0.177 10 *e 5.979,1.396 6.188,1.552 0.208,0.156 10 *f 5.281,1.396 5.479,1.573 0.198,0.177 10 *f 6.656,1.396 6.833,1.552 0.177,0.156 10 *f 6.656,0.792 6.823,0.958 0.167,0.167 10 *f 2.51,1.396 2.688,1.573 0.177,0.177 10 *c 3.219,0.792 3.396,0.948 0.177,0.156 10 *c 3.927,0.792 4.115,0.979 0.188,0.188 10 *c 4.604,0.792 4.781,0.958 0.177,0.167 10 *c 4.385,6.375 4.531,6.531 0.146,0.156 10 *f 3.01,6.375 3.198,6.531 0.188,0.156 10 *f 3.708,6.375 3.948,6.542 0.24,0.167 10 *f 5.094,6.375 5.302,6.573 0.208,0.198 10 *f 5.083,5.75 5.271,5.906 0.188,0.156 10 *f 4.375,5.75 4.573,5.906 0.198,0.156 10 *e 2.313,6.375 2.521,6.542 0.208,0.167 10 *e 1.625,6.375 1.771,6.531 0.146,0.156 10 *d 3.688,5.75 3.875,5.938 0.188,0.188 10 *d 3.01,5.75 3.208,5.938 0.198,0.188 10 *c 1.625,5.74 1.802,5.927 0.177,0.188 10 *c 2.323,5.75 2.5,5.906 0.177,0.156 10 *c 5.781,6.375 5.969,6.542 0.188,0.167 10 *c 5.771,5.75 5.979,5.938 0.208,0.188 10 *c
*A Table (2) (To move the axle hub toward the negative side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c Standard Bolt *d 90105-17013
*e 90105-17014 *f 90105-17015




j.

If the camber was out of adjustment in the previous step, perform the adjust camber steps mentioned above. In step A, replace the existing bolts with the selected bolts.

HINT:

Replace one bolt at a time when replacing both bolts.



Hide 6.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


d.
C188968C01
0.833,0.583 0.833,1.115 false 1.365,0.583 1.365,0.99 1.365,0.99 0.833,0.99 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 *a 2.427,1.698 2.604,1.854 0.177,0.156 10 *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step C again.



f.
C188969C01
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Specified Condition
NORMAL 205/65R16 C + D: 0°11' +/- 0°10' (0.19° +/- 0.17°)
B - A: 2.2 +/- 2.0 mm (0.0866 +/- 0.0787 in.)
215/55R17 C + D: 0°11' +/- 0°10' (0.19° +/- 0.17°)
B - A: 2.2 +/- 2.0 mm (0.0866 +/- 0.0787 in.)
235/45R18 C + D: 0°11' +/- 0°10' (0.19° +/- 0.17°)
B - A: 2.2 +/- 2.0 mm (0.0866 +/- 0.0787 in.)
SPORT 215/55R17 C + D: 0°10' +/- 0°10' (0.17° +/- 0.17°)
B - A: 2.0 +/- 2.0 mm (0.0787 +/- 0.0787 in.)
235/45R18 C + D: 0°10' +/- 0°10' (0.17° +/- 0.17°)
B - A: 2.0 +/- 2.0 mm (0.0787 +/- 0.0787 in.)


Toe-in (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Specified Condition
NORMAL 215/55R17 C + D: 0°12' +/- 0°10' (0.21° +/- 0.17°)
B - A: 2.4 +/- 2.0 mm (0.0945 +/- 0.0787 in.)
235/45R18 C + D: 0°12' +/- 0°10' (0.21° +/- 0.17°)
B - A: 2.4 +/- 2.0 mm (0.0945 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the steering rack ends.


Hide 7.ADJUST TOE-IN

a.
C370168C01
1.625,1.604 1.865,1.792 0.24,0.188 10 true *a
*a Thread Length


Make sure that the thread length of the right and left steering rack ends are approximately the same.

Standard Difference:

1.5 mm (0.0591 in.) or less



b.

Separate the steering rack boot clips from the steering rack boot.


c.
C370169

Loosen the tie rod assembly lock nuts.


d.

Adjust the steering rack ends if the difference in thread length between the right and left steering rack ends is not within the specified range.

i.

If the toe-in measurement is greater than the specified range (too much toe-out), extend the shorter rack end so that the difference in length is within the specified range.


ii.

If the toe-in measurement is less than the specified range (too much toe-in), shorten the longer rack end so that the difference in length is within the specified range.


iii.

Measure the toe-in.



e.
C317577C06
1.625,0.51 1.781,0.708 0.156,0.198 10 false A 1.667,1.365 1.823,1.563 0.156,0.198 10 false B 1.031,0.323 1.188,0.521 0.156,0.198 10 false C 2.208,0.344 2.365,0.542 0.156,0.198 10 false D
V100135

Front of the Vehicle


Turn the right and left steering rack ends by an equal amount to adjust the toe-in.

HINT:

Perform adjustments so that the value is as close as possible to the median of the specified range.


Toe-in (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Specified Condition
NORMAL 205/65R16 C + D: 0°11' +/- 0°10' (0.19° +/- 0.17°)
B - A: 2.2 +/- 2.0 mm (0.0866 +/- 0.0787 in.)
215/55R17 C + D: 0°11' +/- 0°10' (0.19° +/- 0.17°)
B - A: 2.2 +/- 2.0 mm (0.0866 +/- 0.0787 in.)
235/45R18 C + D: 0°11' +/- 0°10' (0.19° +/- 0.17°)
B - A: 2.2 +/- 2.0 mm (0.0866 +/- 0.0787 in.)
SPORT 215/55R17 C + D: 0°10' +/- 0°10' (0.17° +/- 0.17°)
B - A: 2.0 +/- 2.0 mm (0.0787 +/- 0.0787 in.)
235/45R18 C + D: 0°10' +/- 0°10' (0.17° +/- 0.17°)
B - A: 2.0 +/- 2.0 mm (0.0787 +/- 0.0787 in.)


Toe-in (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Specified Condition
NORMAL 215/55R17 C + D: 0°12' +/- 0°10' (0.21° +/- 0.17°)
B - A: 2.4 +/- 2.0 mm (0.0945 +/- 0.0787 in.)
235/45R18 C + D: 0°12' +/- 0°10' (0.21° +/- 0.17°)
B - A: 2.4 +/- 2.0 mm (0.0945 +/- 0.0787 in.)



f.

Make sure that the thread length of the right and left steering rack ends are the same.


g.

Tighten the tie rod assembly lock nuts.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)


h.
C375205C02
1.01,0.969 1.354,1.198 0.344,0.229 10 false *a 1.229,1.583 1.625,1.854 0.396,0.271 10 false 45° 0.865,1.625 1.24,1.906 0.375,0.281 10 false 90° 2.99,1.594 3.406,1.969 0.417,0.375 10 false 22.5°
*a Clip Tab Positioning Area
V100135

Up
V100136

Rear of Vehicle


Place the steering rack boots on the seats and install the steering rack boot clips.

HINT:
·

Make sure that the steering rack boots are not twisted.

·

Make sure that the tabs of the steering rack boot clip are positioned within the area shown in the illustration.




Hide 8.INSPECT WHEEL ANGLE

a.
C132439C03
0.863,0.204 1.036,0.381 0.173,0.177 10 *b 0.538,0.204 0.713,0.381 0.176,0.177 10 *a 2.397,0.204 2.57,0.381 0.173,0.177 10 *b 2.725,0.204 2.901,0.381 0.176,0.177 10 *a
*a Inside
*b Outside
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of a turning radius gauge.


b.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


Wheel Turning Angle (Unloaded Vehicle) (except Rough Road Area Specification):
Suspension Type Tire Size Inside Wheel Outside Wheel
NORMAL 205/65R16 38°15' +/- 2°00' (38.25° +/- 2.00°) 32°50' (32.83°)
215/55R17 38°15' +/- 2°00' (38.25° +/- 2.00°) 32°50' (32.83°)
235/45R18 36°55' +/- 2°00' (36.92° +/- 2.00°) 32°00' (32.00°)
SPORT 215/55R17 38°15' +/- 2°00' (38.25° +/- 2.00°) 32°50' (32.83°)
235/45R18 36°55' +/- 2°00' (36.92° +/- 2.00°) 31°55' (31.92°)


Wheel Turning Angle (Unloaded Vehicle) (for Rough Road Area Specification):
Suspension Type Tire Size Inside Wheel Outside Wheel
NORMAL 215/55R17 38°40' +/- 2°00' (38.67° +/- 2.00°) 33°05' (33.08°)
235/45R18 37°20' +/- 2°00' (37.33° +/- 2.00°) 32°15' (32.25°)


If the right and left inside wheel angles differ from the specified value, check and adjust the right and left steering rack end lengths.



Hide 9. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 10. PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION