Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2019.02
RM33C0E _58 Vehicle Interior _065464 HEATING / AIR CONDITIONING _0329891 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Recirculated/Fresh Air Modes Switch without User Input  


DESCRIPTION

If recirculation/fresh mode changes unintentionally and without permission, the following causes are possible.

Symptom Factor
·

Recirculation/fresh mode changes without permission

·

Recirculation/fresh mode light blinks


·

Customize setting

·

Change in ambient air temperature

·

Decrease in refrigerant pressure

·

Air conditioner pressure sensor circuit malfunction

·

Engine coolant temperature (high)



PROCEDURE

1.CHECK CUSTOMIZE SETTING
a.

Using the GTS, check that the customize setting Air Inlet Mode is not set to "Automatic".

Air Conditioner
Tester Display Description Default Setting ECU
Air Inlet Mode Function to change the mode automatically to recirculation air mode when turning the A/C on to cool the cabin quickly Automatic 0:Automatic,1:Manual Air conditioning amplifier assembly
50006 11
OK:

Air Inlet Mode is not set to "Automatic".



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

CUSTOMIZE SETTING

Set Air Inlet Mode to "Manual"


2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Ambient Temp Sensor Thermistor assembly Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature displayed Thermistor assembly circuit malfunction
·

When open circuit: -23.30°C (-9.94°F)

·

When short circuit: 65.95°C (150.71°F)


Body Electrical > Air Conditioner > Data List
Tester Display
Ambient Temp Sensor
50003 121 2
OK:

The value of the display does not change frequently.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature Min.: -40°C (-40°F), Max.: 140°C (284°F) 75 to 100°C (167 to 212°F): After warming up This is the engine coolant temperature.
HINT:
·

After warming up the engine, the engine coolant temperature will be 75 to 100°C (167 to 212°F).

·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.

·

If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted.

·

Check if the engine overheats if the value indicated is higher than 135°C (275°F).



Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
OK:

The value of the display does not change frequently.



Result:
Proceed to
OK
NG



OK

4.CHECK REFRIGERANT PRESSURE

NG

4.CHECK REFRIGERANT PRESSURE
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Regulator Pressure Sensor Air conditioner pressure sensor Min.: -0.4566 MPaG
Max.: 3.2943 MPaG
Actual refrigerant pressure displayed
·

Refrigerant line (gas leak etc.)

·

Air conditioner pressure sensor circuit malfunction


Body Electrical > Air Conditioner > Data List
Tester Display
Regulator Pressure Sensor
50003 121 52

f.

Install a manifold gauge set.


g.

Read the manifold gauge pressure when the following conditions are met.

i.

Prepare the vehicle according to the table below.

Measurement Condition:
Item Condition
Vehicle doors Fully open
Temperature setting MAX COLD
Blower speed HI
A/C switch On
Recirculation/fresh switch RECIRCULATION
Interior temperature 25 to 35°C (77 to 95°F)



Standard Pressure:
Low pressure side:

150 to 250 kPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)

High pressure side:

1370 to 1570 kPa (14 to 16 kgf/cm2, 199 to 228 psi)


h.

Compare the values displayed in the Data List and on the manifold gauge.

OK:

The values displayed in the Data List and on the manifold gauge match.



Result:
Proceed to
OK
NG



OK

GO TO ON-VEHICLE INSPECTION (CHECK REFRIGERANT PRESSURE USING GAUGE)

NG