Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2019.02
RM33C0E _58 Vehicle Interior _065456 THEFT DETERRENT / KEYLESS ENTRY _0389661 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit between terminal ACCD of the certification ECU (smart key ECU assembly) and the ACC relay.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2274 ACC Monitor Malfunction The ACC relay circuit of the certification ECU (smart key ECU assembly) is malfunctioning. (1-trip detection logic*)
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

Instrument panel junction block assembly

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Wait 10 seconds after turning the power switch on (ACC) or on (IG), and then wait another 10 seconds after turning the power switch off.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the ACC relay being stuck on, the ACC relay does not turn off even though the power switch is off.

·

If there is a malfunction due to the ACC relay being stuck off, the ACC relay does not turn on even though the power switch is on (ACC).


HINT:

The power switch can be turned on (IG) and the hybrid control system can be started.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2274
Power Source Control
·

ACC Relay Monitor



WIRING DIAGRAM

B481556E04
2.198,1.396 2.76,1.667 0.563,0.271 10 false ACC 0.948,1.656 3.896,1.906 2.948,0.25 10 false Instrument Panel Junction Block Assembly 5.49,1.625 6.052,1.896 0.563,0.271 10 false K62 5.479,1.792 6.99,2.25 1.51,0.458 10 false Certification ECU (Smart Key ECU Assembly) 5.792,1.042 6.354,1.313 0.563,0.271 10 false ACCD 5.531,1.042 6.094,1.313 0.563,0.271 10 false 16 6.125,0.646 6.688,0.917 0.563,0.271 10 false +B 0.854,0.656 1.417,0.927 0.563,0.271 10 false 3D 0.854,1.135 1.417,1.406 0.563,0.271 10 false 3B 3.427,0.646 3.99,0.917 0.563,0.271 10 false 3F 3.458,0.458 4.021,0.729 0.563,0.271 10 false 1 3.438,0.948 4,1.219 0.563,0.271 10 false 30 0.896,0.938 1.458,1.208 0.563,0.271 10 false 3 0.854,0.458 1.417,0.729 0.563,0.271 10 false 26 1.323,0.792 2.094,1.042 0.771,0.25 10 false ECU-ACC 3.448,1.135 4.01,1.406 0.563,0.271 10 false 3A 6.563,0.979 6.948,1.281 0.385,0.302 10 false IC

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 3A, 3B and 3F instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K62-16 (ACCD) - 3A-30 Always Below 1 Ω
3B-3 - Body ground Always Below 1 Ω
K62-16 (ACCD) or 3A-30 - Other terminals and body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect all of the instrument panel junction block assembly connectors.


c.

Connect the K62 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

B463118C13
2.26,2.333 2.573,2.542 0.313,0.208 0.083,0.125 0.396,0.281 0.313,0.156 10 false *a 2.344,2.365 2.656,2.521 0.313,0.156 10 false 3D
*a Component with harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
3D-26 - Body ground Power switch on (ACC) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B424427C60
1.542,0.083 1.958,0.333 0.417,0.25 1.052,1.969 1.302,1.969 1.302,1.969 1.302,0.969 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.615,0.115 1.969,0.375 0.354,0.26 10 false K62 0.635,1.875 1.135,2.115 0.5,0.24 10 false ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K62-16 (ACCD) - Body ground Power switch off → Power switch on (ACC) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)