This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator or upper bracket assembly) via direct line and the steering lock position signal sent via LIN communication do not match.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2285 | Steering Lock Position Signal Circuit Malfunction | The steering lock position signal sent by the steering lock ECU (steering lock actuator or upper bracket assembly) via direct line and the steering lock position signal sent via LIN communication do not match. (1-trip detection logic*) | ·
LIN communication system ·
Steering lock ECU (steering lock actuator or upper bracket assembly) ·
Certification ECU (smart key ECU assembly) ·
Wire harness or connector |
DTC Output Confirmation Operation:
Disconnect the cable from the negative (-) auxiliary battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) auxiliary battery terminal. Wait at least 40 seconds with the power switch off (wait is the steering locked), then turn the power switch on (IG) (steering unlocked) and wait at least 40 seconds. |
*: Only detected while a malfunction is present and the power switch is on (IG).
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| The hybrid control system cannot be started. | The ECU does not send a hybrid control system start request. |
| DTC No. | Data List and Active Test |
|---|---|
| B2285 | Power Source Control
Steering Unlock Switch Smart Key
·
Power Supply Short ·
Motor Driver Short ·
Lock Bar Stuck Error |
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly), refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
Check for DTCs.
If the steering cannot be unlocked, the power switch cannot be turned on (IG) and the hybrid control system cannot be started.
If LIN communication is not available, the steering cannot be locked or unlocked.
LIN communication system DTC B2785 is not output simultaneously.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Unlock Switch | State of steering unlock sensor signal output from steering lock ECU (steering lock actuator or upper bracket assembly) | OFF or ON | OFF: Steering locked
ON: Steering unlocked |
·
When the shift lever is in P and the power switch is off, if any door is opened or closed, the steering is locked. ·
When the electrical key transmitter sub-assembly is in the cabin and the power switch is turned on (ACC) or on (IG), the steering unlocks. ·
The hybrid control system cannot be started when the steering unlock signal is off. |
| Tester Display |
|---|
| Steering Unlock Switch |
The GTS display changes.
| Proceed to |
|---|
| OK |
| NG |
OK
for Manual Tilt and Manual Telescopic Steering Column Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY
for Power Tilt and Power Telescopic Steering Column Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY
NG
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | |
|---|---|---|---|
| K65-4 (SLP1) - Body ground | Positive (+) tester probe → K65-4 (SLP1)
Negative (-) tester probe → Body ground |
Steering locked → unlocked* | 10 kΩ or higher → Below 1 Ω |
*: If any of the doors are opened with the shift lever in P and the power switch off, the steering will be locked. If the power switch is turned on (ACC) or on (IG) with the electrical key transmitter sub-assembly in the cabin, the steering will be unlocked.
DTC B2285 may be stored due to a malfunction in the steering lock ECU (steering lock actuator or upper bracket assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator or upper bracket assembly) to the certification ECU (smart key ECU assembly) individually.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Tilt and Manual Telescopic Steering Column: Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY
for Power Tilt and Power Telescopic Steering Column Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY
Disconnect the K62 certification ECU (smart key ECU assembly) connector.
Disconnect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K62-14 (SLP) - K65-4 (SLP1) | Always | Below 1 Ω |
| K62-14 (SLP) or K65-4 (SLP1) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG