Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2019.02
RM33C0E _58 Vehicle Interior _065456 THEFT DETERRENT / KEYLESS ENTRY _0389661 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B279986  Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid  


DESCRIPTION

If there is a communication malfunction between the hybrid vehicle control ECU assembly and certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2, or when the communication ID codes do not match, the hybrid vehicle control ECU assembly stores this DTC.

*1: w/o ID Code Box

*2: w/ ID Code Box


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279986 Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid Either of the following conditions is met (1 trip detection logic*1):
·

A malfunction is detected in the communication or communication lines between the hybrid vehicle control ECU assembly and certification ECU (smart key ECU assembly)*2 or ID code box (immobiliser code ECU)*3.

·

The communication ID codes of the hybrid vehicle control ECU assembly and certification ECU (smart key ECU assembly)*2 or ID code box (immobiliser code ECU)*3 do not match.


·

Certification ECU (smart key ECU assembly)*2

·

ID code box (immobiliser code ECU)*3

·

Hybrid vehicle control ECU assembly

·

Wire harness or connector


DTC output confirmation operation (Perform either of the following):
·

Start the hybrid control system and wait for 10 seconds. If there is a malfunction, the hybrid control system will stop (communication begins within 3 seconds of the hybrid control system start operation being performed, and DTCs are stored after 6 seconds).

·

Connect the cable to the negative (-) auxiliary battery terminal, start the hybrid control system and wait for 10 seconds (communication begins within 3 seconds of the power switch being turned on (IG), and DTCs are stored after 6 seconds).



*1: Only output while a malfunction is present.

*2: w/o ID Code Box

*3: w/ ID Code Box


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B279986 -

WIRING DIAGRAM

w/o ID Code Box


B463090E06
0.385,3.052 1.771,3.573 1.385,0.521 10 false Hybrid Vehicle Control ECU Assembly 0.385,2.896 0.844,3.094 0.458,0.198 10 false K70 5.313,2.896 5.771,3.094 0.458,0.198 10 false A13 5.979,0.24 6.438,0.438 0.458,0.198 10 false 12 V 1.125,1.375 1.583,1.573 0.458,0.198 10 false 12 V 5.292,0.969 5.75,1.167 0.458,0.198 10 false EFII 5.302,1.865 5.76,2.063 0.458,0.198 10 false EFIO 5.104,0.969 5.563,1.167 0.458,0.198 10 false 3 5.104,1.865 5.563,2.063 0.458,0.198 10 false 4 1.625,0.958 2.083,1.156 0.458,0.198 10 false IMO 1.688,1.875 2.146,2.073 0.458,0.198 10 false IMI 1.99,0.948 2.448,1.146 0.458,0.198 10 false 23 1.969,1.865 2.427,2.063 0.458,0.198 10 false 22 5.313,3.052 6.823,3.458 1.51,0.406 10 false Certification ECU (Smart Key ECU Assembly)


w/ ID Code Box


B463090E43
0.385,3.052 1.802,3.573 1.417,0.521 10 false Hybrid Vehicle Control ECU Assembly 0.385,2.896 0.844,3.094 0.458,0.198 10 false K70 5.313,2.896 5.771,3.094 0.458,0.198 10 false K159 5.979,0.24 6.438,0.438 0.458,0.198 10 false 12 V 1.125,1.375 1.583,1.573 0.458,0.198 10 false 12 V 5.292,0.969 5.75,1.167 0.458,0.198 10 false EFII 5.302,1.865 5.76,2.063 0.458,0.198 10 false EFIO 5.104,0.969 5.563,1.167 0.458,0.198 10 false 3 5.104,1.865 5.563,2.063 0.458,0.198 10 false 4 1.625,0.958 2.083,1.156 0.458,0.198 10 false IMO 1.688,1.875 2.146,2.073 0.458,0.198 10 false IMI 1.99,0.948 2.448,1.146 0.458,0.198 10 false 23 1.969,1.865 2.427,2.063 0.458,0.198 10 false 22 5.302,3.052 6.885,3.438 1.583,0.385 10 false ID Code Box (Immobiliser Code ECU)


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the hybrid vehicle control ECU assembly, certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2, refer to Service Bulletin.

*1: w/o ID Code Box

*2: w/ ID Code Box


·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When DTC B279986 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

2.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMO)
2.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B384259C18
5.156,0.25 5.573,0.5 0.417,0.25 5.531,2.365 5.292,2.365 5.292,2.365 5.292,1.375 true 3.333,4.49 3.115,4.49 3.115,4.49 3.115,3.927 false 2.688,4.49 2.917,4.49 2.917,4.49 2.917,3.927 false 0.208,0.115 0.458,0.344 0.25,0.229 10 false *a 5.229,0.292 5.604,0.521 0.375,0.229 10 false K70 5.573,2.281 5.948,2.51 0.375,0.229 10 false IMO 0.948,3.885 1.323,4.115 0.375,0.229 10 false GND 2.958,2.969 3.177,3.125 0.219,0.156 10 false *b 3.385,4.427 3.604,4.583 0.219,0.156 10 false *d 2.521,4.427 2.74,4.583 0.219,0.156 10 false *c
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
K70-23 (IMO) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
Normal waveform A
Terminal EFII stuck low (2.4 V or less) B
Waveform not output, or has abnormal wavelength or shape C



A

3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI)

B

6.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY

C

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B384260C17
5.167,0.177 5.583,0.427 0.417,0.25 5.667,2.406 5.385,2.406 5.385,2.406 5.385,1.385 true 3.729,4.604 3.5,4.604 3.5,4.604 3.5,4.042 false 3.094,4.604 3.313,4.604 3.313,4.604 3.313,4.042 false 0.26,0.104 0.521,0.302 0.26,0.198 10 false *a 5.25,0.219 5.615,0.417 0.365,0.198 10 false K70 5.708,2.313 6.073,2.51 0.365,0.198 10 false IMI 3.344,3 3.656,3.25 0.313,0.25 10 false *b 0.938,4 1.354,4.198 0.417,0.198 10 false GND 2.927,4.542 3.24,4.792 0.313,0.25 10 false *c 3.781,4.542 4.094,4.792 0.313,0.25 10 false *d
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
K70-22 (IMI) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

4.REGISTER ECU COMMUNICATION ID

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the power switch on (IG).


b.

Check that the hybrid control system starts 5 seconds after the power switch turned on (IG).

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

6.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY
a.

Disconnect the K70 hybrid vehicle control ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K70-23 (IMO) - Body ground Power switch turned on (IG) using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) (w/o ID Code Box) A
Terminal IMO stuck low (2.4 V or less) (w/ ID Code Box) B
Terminal IMO stuck high (12 V) or abnormal waveform C



A

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

B

8.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBLISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

C

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the A13 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-3 (EFII) - K70-23 (IMO) Always Below 1 Ω
A13-3 (EFII) or K70-23 (IMO) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBLISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the K159 ID code box (immobliser code ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K159-3 (EFII) - K70-23 (IMO) Always Below 1 Ω
K159-3 (EFII) or K70-23 (IMO) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR