Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2019.02
RM33C0E _58 Vehicle Interior _065456 THEFT DETERRENT / KEYLESS ENTRY _0389661 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B279A12  Engine Immobiliser System Circuit Short to Battery  


DESCRIPTION

If the communication line (IMI - EFIO) between the hybrid vehicle control ECU assembly and certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 is stuck high, the hybrid vehicle control ECU assembly will store this DTC.

*1: w/o ID Code Box

*2: w/ ID Code Box


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A12 Engine Immobiliser System Circuit Short to Battery The communication line (IMI - EFIO) between the hybrid vehicle control ECU assembly and certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 is stuck high. (1 trip detection logic*3)
·

Certification ECU (smart key ECU assembly)*1

·

ID code box (immobiliser code ECU)*2

·

Hybrid vehicle control ECU assembly

·

Wire harness or connector


DTC output confirmation operation:

Turn the power switch on (IG) and wait 6 seconds.



*1: w/o ID Code Box

*2: w/ ID Code Box

*3: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started Hybrid control system cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A12 -

WIRING DIAGRAM

w/o ID Code Box


B463091E06
0.615,1.865 1.99,2.292 1.375,0.427 10 false Hybrid Vehicle Control ECU Assembly 0.625,1.698 1.083,1.896 0.458,0.198 10 false K70 0.792,0.219 1.25,0.417 0.458,0.198 10 false 12 V 1.865,0.729 2.323,0.927 0.458,0.198 10 false IMI 2.177,0.719 2.635,0.917 0.458,0.198 10 false 22 4.917,0.719 5.375,0.917 0.458,0.198 10 false 4 5.135,0.719 5.594,0.917 0.458,0.198 10 false EFIO 5.125,1.677 5.583,1.875 0.458,0.198 10 false A13 5.115,1.833 6.646,2.24 1.531,0.406 10 false Certification ECU (Smart Key ECU Assembly)


w/ ID Code Box


B463091E43
0.615,1.865 2.01,2.292 1.396,0.427 10 false Hybrid Vehicle Control ECU Assembly 0.625,1.698 1.083,1.896 0.458,0.198 10 false K70 0.792,0.219 1.25,0.417 0.458,0.198 10 false 12 V 1.865,0.729 2.323,0.927 0.458,0.198 10 false IMI 2.177,0.719 2.635,0.917 0.458,0.198 10 false 22 4.917,0.719 5.375,0.917 0.458,0.198 10 false 4 5.135,0.719 5.594,0.917 0.458,0.198 10 false EFIO 5.125,1.677 5.583,1.875 0.458,0.198 10 false K159 5.115,1.833 6.708,2.24 1.594,0.406 10 false ID Code Box (Immobiliser Code ECU)


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the hybrid vehicle control ECU assembly, certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2, refer to Service Bulletin.

*1: w/o ID Code Box

*2: w/ ID Code Box


·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When DTC B279A12 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CHECK CONNECTION OF CONNECTOR
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the hybrid vehicle control ECU assembly and certification ECU (smart key ECU assembly).

OK:

Connectors are properly connected.



Result:
Result Proceed to
OK (w/o ID Code Box) A
OK (w/ ID Code Box) B
NG C



A

2.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI)

B

4.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI)

C

CONNECT CONNECTORS PROPERLY

2.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B384260C18
5.167,0.177 5.583,0.427 0.417,0.25 5.667,2.406 5.385,2.406 5.385,2.406 5.385,1.385 true 3.729,4.604 3.5,4.604 3.5,4.604 3.5,4.042 false 3.094,4.604 3.313,4.604 3.313,4.604 3.313,4.042 false 0.26,0.104 0.521,0.302 0.26,0.198 10 false *a 5.25,0.219 5.615,0.417 0.365,0.198 10 false K70 5.708,2.313 6.073,2.51 0.365,0.198 10 false IMI 3.344,3 3.656,3.25 0.313,0.25 10 false *b 0.938,4 1.354,4.198 0.417,0.198 10 false GND 2.927,4.542 3.24,4.792 0.313,0.25 10 false *c 3.781,4.542 4.094,4.792 0.313,0.25 10 false *d
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
K70-22 (IMI) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


Result:
Result Proceed to
11 to 14 V A
Below 1 V B
Normal waveform




A

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the K70 hybrid vehicle control ECU assembly connector.


b.

Disconnect the A13 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-4 (EFIO) - K70-22 (IMI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B384260C43
5.167,0.177 5.583,0.427 0.417,0.25 5.667,2.406 5.385,2.406 5.385,2.406 5.385,1.385 true 3.729,4.604 3.5,4.604 3.5,4.604 3.5,4.042 false 3.094,4.604 3.313,4.604 3.313,4.604 3.313,4.042 false 0.26,0.104 0.521,0.302 0.26,0.198 10 false *a 5.24,0.219 5.604,0.417 0.365,0.198 10 false K70 5.708,2.313 6.073,2.51 0.365,0.198 10 false IMI 3.344,3 3.656,3.25 0.313,0.25 10 false *b 0.938,4 1.354,4.198 0.417,0.198 10 false GND 2.927,4.542 3.24,4.792 0.313,0.25 10 false *c 3.781,4.542 4.094,4.792 0.313,0.25 10 false *d
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
K70-22 (IMI) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
11 to 14 V A
Below 1 V B
Normal waveform



A

5.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the K70 hybrid vehicle control ECU assembly connector.


b.

Disconnect the K159 ID code box (immobiliser code ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K159-4 (EFIO) - K70-22 (IMI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR