The certification ECU (smart key ECU assembly) blinks the security indicator light (telltale light assembly)*1 or security indicator light (clock assembly)*2 when the immobiliser is set (power switch off).
The certification ECU (smart key ECU assembly) receives the security indicator light signal from the main body ECU (multiplex network body ECU) via CAN communication when the theft deterrent system is in the arming preparation state or alarm sounding state. Then, the certification ECU (smart key ECU assembly) blinks the security indicator light (telltale light assembly)*1 or security indicator light (clock assembly)*2.
*1: w/ Telltale Light Assembly
*2: w/ Clock Assembly
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.
Check for DTCs.
DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Immobiliser Indicator | Security indicator light | OFF/ON | - |
| Tester Display |
|---|
| Immobiliser Indicator |
The security indicator light operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
When the immobiliser is set, check that the security indicator light blinks.*1
The security indicator light blinks normally.
When the theft deterrent system is in the arming preparation state, check that the security indicator light illuminates.*2
The security indicator light illuminates normally.
| Result | Proceed to |
|---|---|
| *1 is NG (*2 is OK) | A |
| *2 is NG (*1 is OK) | B |
A
B
Disconnect the K62 certification ECU (smart key ECU assembly) connector.
Disconnect the K36 security indicator light (telltale light assembly) connector.*1
Disconnect the K59 security indicator light (clock assembly) connector.*2
*1: w/ Telltale Light Assembly
*2: w/ Clock Assembly
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K62-20 (IND) - K36-9 (LP) | Always | Below 1 Ω |
| K62-20 (IND) or K36-9 (LP) - Other terminals and body ground | Always | 10 kΩ or higher |
| K36-6 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K62-20 (IND) - K59-5 (LP) | Always | Below 1 Ω |
| K62-20 (IND) or K59-5 (LP) - Other terminals and body ground | Always | 10 kΩ or higher |
| K59-7 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K62 certification ECU (smart key ECU assembly) connector.
Connect the K36 security indicator light (telltale light assembly) connector.*1
Connect the K59 security indicator light (clock assembly) connector.*2
*1: w/ Telltale Light Assembly
*2: w/ Clock Assembly
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K62-20 (IND) - Body ground | Power switch off → on (IG) | Pulse generation → Below 2 V |
| Result | Proceed to |
|---|---|
| OK (w/ Telltale Light Assembly) | A |
| OK (w/ Clock Assembly) | B |
| NG | C |
A
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>REMOVAL
B
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>REMOVAL
C