Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › from 2019.02
RM33C0E _58 Vehicle Interior _065455 DOOR LOCK _0333664 WIRELESS DOOR LOCK CONTROL SYSTEM U

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B472410C09
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 5.302,6.396 5.74,6.646 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.302,6.083 5.74,6.333 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 5.385,4.615 5.823,4.865 0.438,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 0.531,2.49 0.531,2.323 0.531,2.323 0.865,2.323 false 3.469,7.677 3.781,7.875 0.313,0.198 10 false MB 4.292,0.219 4.604,0.417 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false K51 2.052,1.479 2.365,1.677 0.313,0.198 10 false K52 2.052,1.802 2.365,2 0.313,0.198 10 false K53 0.875,1.073 1.188,1.271 0.313,0.198 10 false 3D 0.875,1.656 1.188,1.854 0.313,0.198 10 false 3C 0.885,2.021 1.198,2.219 0.313,0.198 10 false 3E 5.854,1.146 6.167,1.344 0.313,0.198 10 false 3B 5.854,1.76 6.167,1.958 0.313,0.198 10 false 3A 1.229,3.281 1.542,3.479 0.313,0.198 10 false K53 3.271,3.25 3.583,3.448 0.313,0.198 10 false K52 5.542,3.24 5.854,3.438 0.313,0.198 10 false K51 1.833,4.604 2.146,4.802 0.313,0.198 10 false 3A 1.24,6.198 1.552,6.396 0.313,0.198 10 false 3C 3.813,6.156 4.125,6.354 0.313,0.198 10 false 3D 5.427,6.115 5.74,6.313 0.313,0.198 10 false 3F 6.448,6.229 6.76,6.427 0.313,0.198 10 false 3E 5.521,4.646 5.833,4.844 0.313,0.198 10 false 3B 5.427,6.427 5.74,6.625 0.313,0.198 10 false 3G 5.813,6.125 6.125,6.323 0.313,0.198 10 false *A 5.823,6.427 6.135,6.625 0.313,0.198 10 false *B 0.365,2.531 0.76,2.76 0.396,0.229 10 false 3F*A 0.365,2.698 0.865,2.885 0.5,0.188 10 false 3G*B
*A for LHD *B for RHD


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click here


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
MB-11 (GND1) - Body ground - - Ground Always Below 1 Ω -
MB-30 (ACC) - Body ground - Input ACC power supply Power switch on (ACC) 11 to 14 V ACC SW
Power switch off Below 1 V
MB-31 (BECU) - Body ground - Input Auxiliary battery power supply Power switch off 11 to 14 V -
MB-32 (IG) - Body ground - Input IG power supply Power switch on (IG) 11 to 14 V IG SW
Power switch off Below 1 V


d.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
3C-29 (BZR) - Body ground* L - Body ground Output Wireless door lock buzzer output Active Test Wireless Buzzer is OFF Below 1 V -
Active Test Wireless Buzzer is ON Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V)

*: w/ Wireless Door Lock Buzzer Answer-back Function




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B416786N76
2.063,0.438 2.438,0.677 0.375,0.24 4.552,0.438 4.927,0.677 0.375,0.24 3.313,0.448 3.688,0.688 0.375,0.24 2.125,0.469 2.438,0.667 0.313,0.198 10 false A13 4.615,0.469 4.927,0.667 0.313,0.198 10 false K62 3.417,0.49 3.729,0.688 0.313,0.198 10 false R8

a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
K62-4 (+B) - Body ground W - Body ground Input Auxiliary battery power supply Power switch off 11 to 14 V -
K62-18 (E) - Body ground W-B - Body ground - Ground Always Below 1 Ω -


c.

Reconnect the K62 certification ECU (smart key ECU assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
R8-18 (RCO) - K62-18 (E) B - W-B Output Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Turn power switch off

2.

Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area

3.

Press lock or unlock switch of electrical key transmitter sub-assembly


Plus generation (See waveform 1) -
R8-19 (RDAM) - K62-18 (E) G - W-B Input Door control receiver communication circuit
Procedure:
1.

Turn power switch off

2.

Lock all doors

3.

Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area

4.

Press lock or unlock switch of electrical key transmitter sub-assembly


Plus generation (See waveform 2) -
R8-20 (CSEL) - K62-18 (E) BE - W-B Output Communication channel switching circuit
Procedure:
1.

Turn power switch off

2.

Close all doors


No pulse generation → Pulse generation -


e.
B251178C30
0.198,1 0.531,1.198 0.333,0.198 10 GND 1.01,1.885 1.198,2.042 0.188,0.156 10 *a 2.021,1.885 2.208,2.042 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester connection R8-18 (RCO) - K62-18 (E)
Tool setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Turn power switch off

2.

Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area

3.

Press lock or unlock switch of electrical key transmitter sub-assembly




f.
B251177C33
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester connection R8-19 (RDAM) - K62-18 (E)
Tool setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Turn power switch off

2.

Lock all doors

3.

Bring electrical key transmitter sub-assembly outside detection area but within wireless function operational area

4.

Press lock or unlock switch of electrical key transmitter sub-assembly