Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2019.10
RM33C0E _57 Power Source / Network _065454 NETWORKING _0329710 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 5 Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom Trouble Area
There is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Air conditioning amplifier assembly

·

Certification ECU (smart key ECU assembly)

·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

Meter mirror sub-assembly

(w/ Headup Display System)

·

Headlight ECU sub-assembly LH

(w/ Automatic Headlight Beam Level Control System)

·

Headlight ECU sub-assembly RH

(w/ Automatic Headlight Beam Level Control System)

·

Multiplex tilt and telescopic ECU

(w/ Power Tilt and Power Telescopic System)

·

Position control ECU assembly LH

(for LHD with Seat Position Memory System)

·

Position control ECU assembly RH

(for RHD with Seat Position Memory System)

·

Outer mirror control ECU assembly (for driver side)

(w/ Seat Position Memory System)

·

Outer mirror control ECU assembly (for front passenger side)

(w/ Seat Position Memory System)

·

No. 3 CAN junction connector

·

No. 1 junction connector

·

No. 2 junction connector

·

No. 5 junction connector

(for RHD)

·

No. 6 junction connector

(for LHD)



WIRING DIAGRAM

for LHD
C381552E04
0.406,2.896 2.76,3.635 2.354,0.74 10 false Headlight ECU Sub-assembly RH*2 2.958,2.823 3.417,3.021 0.458,0.198 10 false R97 3.271,2.823 4.188,3.438 0.917,0.615 10 false No. 2 Junction Connector 4.865,1.083 5.323,1.281 0.458,0.198 10 false K76 5.188,1.083 7.125,1.792 1.938,0.708 10 false Central Gateway ECU (Network Gateway ECU) 5.656,0.198 6.115,0.396 0.458,0.198 10 false 15 5.646,0.615 6.104,0.813 0.458,0.198 10 false 16 5.896,0.208 6.354,0.406 0.458,0.198 10 false CA5H 5.896,0.615 6.354,0.813 0.458,0.198 10 false CA5L 6.417,0.542 6.875,0.74 0.458,0.198 10 false 120 Ω 4.188,0.208 4.646,0.406 0.458,0.198 10 false 1 4.156,0.635 4.615,0.833 0.458,0.198 10 false 12 4.208,1.958 4.667,2.156 0.458,0.198 10 false 2 4.167,2.406 4.625,2.604 0.458,0.198 10 false 13 3.073,2.396 3.531,2.594 0.458,0.198 10 false 16 3.125,1.969 3.583,2.167 0.458,0.198 10 false 5 3.094,0.625 3.552,0.823 0.458,0.198 10 false 14 3.146,0.208 3.604,0.406 0.458,0.198 10 false 3 0.833,2.083 1.292,2.281 0.458,0.198 10 false CANH 0.865,2.531 1.323,2.729 0.458,0.198 10 false CANL 1.344,1.979 1.802,2.177 0.458,0.198 10 false 24 1.333,2.406 1.792,2.604 0.458,0.198 10 false 23 5.552,7.219 7.094,7.802 1.542,0.583 10 false Outer Mirror Control ECU Assembly (for Driver Side)*1 5.323,7.219 5.781,7.417 0.458,0.198 10 false O8 0.854,0.74 1.313,0.938 0.458,0.198 10 false CANN 0.865,0.313 1.323,0.51 0.458,0.198 10 false CANP 1.375,0.188 1.833,0.385 0.458,0.198 10 false 9 1.365,0.625 1.823,0.823 0.458,0.198 10 false 8 4.188,3.896 4.646,4.104 0.458,0.208 10 false 1 4.167,4.313 4.625,4.521 0.458,0.208 10 false 12 3.073,5.156 3.531,5.365 0.458,0.208 10 false 13 3.115,3.885 3.573,4.094 0.458,0.208 10 false 3 3.052,4.323 3.51,4.531 0.458,0.208 10 false 14 3.135,4.76 3.594,4.969 0.458,0.208 10 false 2 0.094,4.771 0.552,4.969 0.458,0.198 10 false b22 0.417,4.771 1.771,5.823 1.354,1.052 10 false Position Control ECU Assembly LH*1 0.854,3.99 1.313,4.188 0.458,0.198 10 false CANP 0.844,4.417 1.302,4.615 0.458,0.198 10 false CANN 1.375,3.875 1.833,4.073 0.458,0.198 10 false 13 1.375,4.313 1.833,4.51 0.458,0.198 10 false 14 3.125,6.302 3.583,6.51 0.458,0.208 10 false 4 3.073,6.75 3.531,6.958 0.458,0.208 10 false 15 4.198,6.302 4.656,6.51 0.458,0.208 10 false 1 4.156,6.75 4.615,6.958 0.458,0.208 10 false 12 5.698,6.313 6.156,6.521 0.458,0.208 10 false 9 5.698,6.74 6.156,6.948 0.458,0.208 10 false 8 5.917,6.448 6.375,6.646 0.458,0.198 10 false CANP 5.906,6.875 6.365,7.073 0.458,0.198 10 false CANN 0.073,1.083 0.531,1.281 0.458,0.198 10 false N9 0.302,1.083 2.5,1.781 2.198,0.698 10 false Outer Mirror Control ECU Assembly (for Front Passenger Side)*1 4.156,7.688 4.615,7.896 0.458,0.208 10 false 14 4.198,7.396 4.656,7.604 0.458,0.208 10 false 3 2.635,8.094 3.094,8.302 0.458,0.208 10 false R94 2.938,8.094 4.604,8.354 1.667,0.26 10 false No. 1 Junction Connector 2.583,5.479 3.042,5.688 0.458,0.208 10 false R101 3,5.479 5.073,5.771 2.073,0.292 10 false No. 6 Junction Connector 0.115,7.333 2.885,7.75 2.771,0.417 10 false *1: w/ Seat Position Memory System 0.115,7.844 2.167,8.5 2.052,0.656 10 false *2: w/ Automatic Headlight Beam Level Control System 0.073,2.896 0.531,3.094 0.458,0.198 10 false A79

C381551E03
4.208,0.24 4.438,0.448 0.229,0.208 10 false 3 4.167,0.76 4.396,0.969 0.229,0.208 10 false 14 0.365,1.302 2.573,1.583 2.208,0.281 10 false Headlight ECU Sub-assembly LH*1 0.917,0.354 1.396,0.563 0.479,0.208 10 false CANH 0.927,0.885 1.406,1.094 0.479,0.208 10 false CANL 1.458,0.26 1.688,0.469 0.229,0.208 10 false 24 1.448,0.771 1.677,0.979 0.229,0.208 10 false 23 3.219,0.25 3.448,0.458 0.229,0.208 10 false 8 3.156,0.771 3.385,0.979 0.229,0.208 10 false 19 4.208,2.281 4.438,2.49 0.229,0.208 10 false 4 4.177,2.813 4.406,3.021 0.229,0.208 10 false 15 5.26,3.323 5.604,3.521 0.344,0.198 10 false K62 5.594,3.323 7.125,3.896 1.531,0.573 10 false Certification ECU (Smart Key ECU Assembly) 6.031,2.406 6.51,2.615 0.479,0.208 10 false CANH 6.052,2.948 6.531,3.156 0.479,0.208 10 false CANL 5.792,2.26 6.021,2.469 0.229,0.208 10 false 1 5.792,2.813 6.021,3.021 0.229,0.208 10 false 2 3.188,2.271 3.417,2.479 0.229,0.208 10 false 7 3.156,2.844 3.385,3.052 0.229,0.208 10 false 18 1.438,2.292 1.667,2.5 0.229,0.208 10 false 11 1.427,2.833 1.656,3.042 0.229,0.208 10 false 12 0.906,2.385 1.385,2.594 0.479,0.208 10 false CANH 0.917,2.938 1.396,3.146 0.479,0.208 10 false CANL 0.063,3.354 0.406,3.552 0.344,0.198 10 false K54 0.396,3.344 2.885,3.75 2.49,0.406 10 false Air Conditioning Amplifier Assembly 3.177,4.271 3.406,4.479 0.229,0.208 10 false 6 3.125,4.813 3.354,5.021 0.229,0.208 10 false 17 0.083,5.333 0.427,5.531 0.344,0.198 10 false K52 0.385,5.333 2.021,6.021 1.635,0.688 10 false Main Body ECU (Multiplex Network Body ECU) 0.927,4.406 1.406,4.615 0.479,0.208 10 false CANH 0.948,4.958 1.427,5.167 0.479,0.208 10 false CANL 1.448,4.302 1.677,4.51 0.229,0.208 10 false 5 1.448,4.833 1.677,5.042 0.229,0.208 10 false 4 4.188,4.26 4.417,4.469 0.229,0.208 10 false 9 4.177,4.833 4.406,5.042 0.229,0.208 10 false 20 5.729,4.281 5.958,4.49 0.229,0.208 10 false 12 5.74,4.833 5.969,5.042 0.229,0.208 10 false 13 6.021,4.406 6.5,4.615 0.479,0.208 10 false MPX1 6.042,4.948 6.521,5.156 0.479,0.208 10 false MPX2 5.031,5.323 5.26,5.531 0.229,0.208 10 false p1 5.302,5.333 7.135,5.667 1.833,0.333 10 false Meter Mirror Sub-assembly*2 3.042,7.656 5,8.156 1.958,0.5 10 false No. 3 CAN Junction Connector 2.667,7.656 3.01,7.854 0.344,0.198 10 false K126 0.073,7.521 0.417,7.719 0.344,0.198 10 false K21 0.365,7.521 2.292,7.865 1.927,0.344 10 false Combination Meter Assembly 0.573,6.833 1.073,7.021 0.5,0.188 10 false 120 Ω 1.104,6.51 1.583,6.719 0.479,0.208 10 false CANH 1.135,7.052 1.615,7.26 0.479,0.208 10 false CANL 1.594,6.51 1.823,6.719 0.229,0.208 10 false 32 1.594,7.042 1.823,7.25 0.229,0.208 10 false 31 3.24,6.49 3.469,6.698 0.229,0.208 10 false 5 3.167,7.042 3.396,7.25 0.229,0.208 10 false 16 4.156,7.052 4.385,7.26 0.229,0.208 10 false 21 4.146,6.51 4.375,6.719 0.229,0.208 10 false 10 6.01,6.615 6.49,6.823 0.479,0.208 10 false CANP 6.021,7.167 6.5,7.375 0.479,0.208 10 false CANN 5.823,6.5 6.052,6.708 0.229,0.208 10 false 3 5.75,7.031 5.979,7.24 0.229,0.208 10 false 11 5.063,7.531 5.406,7.729 0.344,0.198 10 false K72 5.375,7.531 7.104,8.031 1.729,0.5 10 false Multiplex Tilt and Telescopic ECU*3 2.625,8.083 4.792,8.365 2.167,0.281 10 false *2: w/ Headup Display System 2.646,8.5 5.573,8.802 2.927,0.302 10 false *3: w/ Power Tilt and Power Telescopic System 0.26,8.052 2.313,8.677 2.052,0.625 10 false *1: w/ Automatic Headlight Beam Level Control System 0.063,1.302 0.521,1.563 0.458,0.26 10 false A78

for RHD
C381552E05
0.396,2.896 2.625,3.26 2.229,0.365 10 false Headlight ECU Sub-assembly RH 2.667,2.823 3.125,3.021 0.458,0.198 10 false R97 2.99,2.823 4.781,3.188 1.792,0.365 10 false No. 2 Junction Connector 4.865,1.083 5.323,1.281 0.458,0.198 10 false K76 5.188,1.083 7.125,1.792 1.938,0.708 10 false Central Gateway ECU (Network Gateway ECU) 5.656,0.198 6.115,0.396 0.458,0.198 10 false 15 5.646,0.615 6.104,0.813 0.458,0.198 10 false 16 5.896,0.208 6.354,0.406 0.458,0.198 10 false CA5H 5.896,0.615 6.354,0.813 0.458,0.198 10 false CA5L 6.417,0.542 6.875,0.74 0.458,0.198 10 false 120 Ω 4.188,0.208 4.646,0.406 0.458,0.198 10 false 1 4.156,0.635 4.615,0.833 0.458,0.198 10 false 12 4.208,1.958 4.667,2.156 0.458,0.198 10 false 2 4.167,2.406 4.625,2.604 0.458,0.198 10 false 13 3.073,2.396 3.531,2.594 0.458,0.198 10 false 16 3.125,1.969 3.583,2.167 0.458,0.198 10 false 5 3.094,0.625 3.552,0.823 0.458,0.198 10 false 14 3.146,0.208 3.604,0.406 0.458,0.198 10 false 3 0.833,2.083 1.292,2.281 0.458,0.198 10 false CANH 0.865,2.531 1.323,2.729 0.458,0.198 10 false CANL 1.344,1.979 1.802,2.177 0.458,0.198 10 false 24 1.333,2.406 1.792,2.604 0.458,0.198 10 false 23 0.292,1.083 2.521,1.448 2.229,0.365 10 false Outer Mirror Control ECU Assembly (for Driver Side)* 0.063,1.083 0.521,1.281 0.458,0.198 10 false N9 0.854,0.74 1.313,0.938 0.458,0.198 10 false CANN 0.865,0.313 1.323,0.51 0.458,0.198 10 false CANP 1.375,0.188 1.833,0.385 0.458,0.198 10 false 9 1.365,0.625 1.823,0.823 0.458,0.198 10 false 8 4.188,3.885 4.646,4.094 0.458,0.208 10 false 5 4.156,4.313 4.615,4.521 0.458,0.208 10 false 16 3.042,5.135 3.5,5.344 0.458,0.208 10 false 17 3.104,3.885 3.563,4.094 0.458,0.208 10 false 7 3.052,4.323 3.51,4.531 0.458,0.208 10 false 18 3.104,4.75 3.563,4.958 0.458,0.208 10 false 6 0.094,4.771 0.552,4.969 0.458,0.198 10 false a31 0.365,4.771 1.719,5.823 1.354,1.052 10 false Position Control ECU Assembly RH* 0.854,3.99 1.313,4.188 0.458,0.198 10 false CANP 0.844,4.417 1.302,4.615 0.458,0.198 10 false CANN 1.375,3.875 1.833,4.073 0.458,0.198 10 false 13 1.375,4.313 1.833,4.51 0.458,0.198 10 false 14 3.125,6.302 3.583,6.51 0.458,0.208 10 false 4 3.073,6.75 3.531,6.958 0.458,0.208 10 false 15 4.198,6.302 4.656,6.51 0.458,0.208 10 false 1 4.156,6.75 4.615,6.958 0.458,0.208 10 false 12 5.698,6.313 6.156,6.521 0.458,0.208 10 false 9 5.698,6.74 6.156,6.948 0.458,0.208 10 false 8 5.917,6.448 6.375,6.646 0.458,0.198 10 false CANP 5.906,6.875 6.365,7.073 0.458,0.198 10 false CANN 5.292,7.219 5.75,7.417 0.458,0.198 10 false O8 5.552,7.219 7.115,7.896 1.563,0.677 10 false Outer Mirror Control ECU Assembly (for Front Passenger Side)* 4.156,7.688 4.615,7.896 0.458,0.208 10 false 14 4.198,7.396 4.656,7.604 0.458,0.208 10 false 3 2.635,8.094 3.094,8.302 0.458,0.208 10 false R94 2.938,8.094 4.604,8.354 1.667,0.26 10 false No. 1 Junction Connector 2.573,5.458 3.031,5.667 0.458,0.208 10 false R100 2.969,5.458 5.042,5.75 2.073,0.292 10 false No. 5 Junction Connector 0.125,7.396 2.604,7.781 2.479,0.385 10 false *: w/ Seat Position Memory System 0.063,2.896 0.625,3.24 0.563,0.344 10 false A79

C381551E04
4.208,0.24 4.438,0.448 0.229,0.208 10 false 3 4.167,0.76 4.396,0.969 0.229,0.208 10 false 14 0.396,1.302 2.604,1.583 2.208,0.281 10 false Headlight ECU Sub-assembly LH 0.917,0.354 1.396,0.563 0.479,0.208 10 false CANH 0.927,0.885 1.406,1.094 0.479,0.208 10 false CANL 1.458,0.26 1.688,0.469 0.229,0.208 10 false 24 1.448,0.771 1.677,0.979 0.229,0.208 10 false 23 3.219,0.25 3.448,0.458 0.229,0.208 10 false 8 3.156,0.771 3.385,0.979 0.229,0.208 10 false 19 4.208,2.281 4.438,2.49 0.229,0.208 10 false 4 4.177,2.813 4.406,3.021 0.229,0.208 10 false 15 5.26,3.323 5.604,3.521 0.344,0.198 10 false K62 5.594,3.323 7.125,3.896 1.531,0.573 10 false Certification ECU (Smart Key ECU Assembly) 6.031,2.406 6.51,2.615 0.479,0.208 10 false CANH 6.052,2.948 6.531,3.156 0.479,0.208 10 false CANL 5.792,2.26 6.021,2.469 0.229,0.208 10 false 1 5.792,2.813 6.021,3.021 0.229,0.208 10 false 2 3.188,2.271 3.417,2.479 0.229,0.208 10 false 7 3.156,2.844 3.385,3.052 0.229,0.208 10 false 18 1.438,2.292 1.667,2.5 0.229,0.208 10 false 11 1.427,2.833 1.656,3.042 0.229,0.208 10 false 12 0.906,2.385 1.385,2.594 0.479,0.208 10 false CANH 0.917,2.938 1.396,3.146 0.479,0.208 10 false CANL 0.063,3.354 0.406,3.552 0.344,0.198 10 false K54 0.396,3.344 2.885,3.75 2.49,0.406 10 false Air Conditioning Amplifier Assembly 3.177,4.271 3.406,4.479 0.229,0.208 10 false 6 3.125,4.813 3.354,5.021 0.229,0.208 10 false 17 0.083,5.333 0.427,5.531 0.344,0.198 10 false K52 0.385,5.333 2.021,6.021 1.635,0.688 10 false Main Body ECU (Multiplex Network Body ECU) 0.927,4.406 1.406,4.615 0.479,0.208 10 false CANH 0.948,4.958 1.427,5.167 0.479,0.208 10 false CANL 1.448,4.302 1.677,4.51 0.229,0.208 10 false 5 1.448,4.833 1.677,5.042 0.229,0.208 10 false 4 4.188,4.26 4.417,4.469 0.229,0.208 10 false 9 4.177,4.833 4.406,5.042 0.229,0.208 10 false 20 5.729,4.281 5.958,4.49 0.229,0.208 10 false 12 5.74,4.833 5.969,5.042 0.229,0.208 10 false 13 6.021,4.406 6.5,4.615 0.479,0.208 10 false MPX1 6.042,4.948 6.521,5.156 0.479,0.208 10 false MPX2 5.031,5.323 5.26,5.531 0.229,0.208 10 false p1 5.302,5.333 7.135,5.667 1.833,0.333 10 false Meter Mirror Sub-assembly*1 2.969,7.656 4.938,8.208 1.969,0.552 10 false No. 3 CAN Junction Connector 2.573,7.656 2.917,7.854 0.344,0.198 10 false K126 0.073,7.521 0.417,7.719 0.344,0.198 10 false K21 0.365,7.521 2.333,7.802 1.969,0.281 10 false Combination Meter Assembly 0.573,6.833 1.073,7.021 0.5,0.188 10 false 120 Ω 1.104,6.51 1.583,6.719 0.479,0.208 10 false CANH 1.135,7.052 1.615,7.26 0.479,0.208 10 false CANL 1.594,6.51 1.823,6.719 0.229,0.208 10 false 32 1.594,7.042 1.823,7.25 0.229,0.208 10 false 31 3.24,6.49 3.469,6.698 0.229,0.208 10 false 5 3.167,7.042 3.396,7.25 0.229,0.208 10 false 16 4.156,7.052 4.385,7.26 0.229,0.208 10 false 21 4.146,6.51 4.375,6.719 0.229,0.208 10 false 10 6.01,6.615 6.49,6.823 0.479,0.208 10 false CANP 6.021,7.167 6.5,7.375 0.479,0.208 10 false CANN 5.823,6.5 6.052,6.708 0.229,0.208 10 false 3 5.75,7.031 5.979,7.24 0.229,0.208 10 false 11 5.063,7.531 5.406,7.729 0.344,0.198 10 false K72 5.375,7.531 7.115,8.104 1.74,0.573 10 false Multiplex Tilt and Telescopic ECU*2 0.25,8.229 2.417,8.51 2.167,0.281 10 false *1: w/ Headup Display System 2.469,8.24 5.583,8.5 3.115,0.26 10 false *2: w/ Power Tilt and Power Telescopic System 0.063,1.302 0.625,1.552 0.563,0.25 10 false A78

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the K126 No. 3 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C402513C60
3.646,1.333 4.083,1.563 0.438,0.229 0.271,1.375 0.708,1.604 0.438,0.229 1.375,0.729 1.542,0.729 1.542,0.729 1.542,1.427 true 1.375,2.115 1.542,2.115 1.542,2.115 1.542,1.698 true 1.708,0.354 1.875,0.354 1.875,0.354 1.875,1.438 true 6.104,2.135 5.938,2.135 5.938,2.135 5.938,1.719 true 1.542,0.552 1.708,0.552 1.708,0.552 1.708,1.438 true 1.875,0.188 2.042,0.188 2.042,0.188 2.042,1.438 true 2.375,0.188 2.208,0.188 2.208,0.188 2.208,1.438 true 2.552,0.344 2.385,0.344 2.385,0.344 2.385,1.427 true 2.708,0.542 2.542,0.542 2.542,0.542 2.542,1.427 true 2.885,0.74 2.719,0.74 2.719,0.74 2.719,1.438 true 1.552,2.26 1.719,2.26 1.719,2.26 1.719,1.677 true 1.708,2.427 1.875,2.427 1.875,2.427 1.875,1.677 true 1.885,2.594 2.052,2.594 2.052,2.594 2.052,1.677 true 2.396,2.604 2.229,2.604 2.229,2.604 2.229,1.688 true 2.563,2.427 2.396,2.427 2.396,2.427 2.396,1.677 true 2.729,2.26 2.563,2.26 2.563,2.26 2.563,1.677 true 2.885,2.094 2.719,2.094 2.719,2.094 2.719,1.677 true 0.24,0.167 0.552,0.365 0.313,0.198 10 false *a 3.719,0.188 4.031,0.385 0.313,0.198 10 false *1 3.719,1.365 4.094,1.563 0.375,0.198 10 false K154 0.344,1.417 0.719,1.615 0.375,0.198 10 false K126 0.802,0.646 1.438,0.885 0.635,0.24 10 false CANH*b 0.833,2.031 1.469,2.271 0.635,0.24 10 false CANL*b 1.021,2.188 1.656,2.427 0.635,0.24 10 false CANL*c 1.177,2.354 1.813,2.594 0.635,0.24 10 false CANL*d 1.354,2.51 1.99,2.677 0.635,0.167 10 false CANL*e 0.969,0.479 1.604,0.719 0.635,0.24 10 false CANH*c 1.146,0.281 1.781,0.521 0.635,0.24 10 false CANH*d 1.313,0.115 1.948,0.354 0.635,0.24 10 false CANH*e 6.177,2.063 6.552,2.26 0.375,0.198 10 false BAT 2.458,0.104 3.094,0.344 0.635,0.24 10 false CANH*f 2.635,0.271 3.271,0.51 0.635,0.24 10 false CANH*g 2.781,0.458 3.417,0.698 0.635,0.24 10 false CANH*h 2.948,0.656 3.583,0.896 0.635,0.24 10 false CANH*i 2.479,2.531 3.115,2.698 0.635,0.167 10 false CANL*f 2.635,2.344 3.271,2.583 0.635,0.24 10 false CANL*g 2.813,2.177 3.448,2.417 0.635,0.24 10 false CANL*h 2.979,2.01 3.615,2.25 0.635,0.24 10 false CANL*i
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to No. 1 Junction Connector
*c to Certification ECU (Smart Key ECU Assembly) *d to Combination Meter Assembly
*e to Main Body ECU (Multiplex Network Body ECU) *f to Air Conditioning Amplifier Assembly
*g to Headlight ECU sub-assembly LH
(w/ Automatic Headlight Beam Level Control System)
*h to Meter Mirror Sub-assembly
(w/ Headup Display System)
*i to Multiplex Tilt and Telescopic ECU
(w/ Power Tilt and Power Telescopic System)
- -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
K126-3 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 1 junction connector
K126-14 (CANL) - K154-16 (BAT)
K126-4 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Certification ECU (smart key ECU assembly)
K126-15 (CANL) - K154-16 (BAT)
K126-5 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Combination meter assembly
K126-16 (CANL) - K154-16 (BAT)
K126-6 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Main body ECU (multiplex network body ECU)
K126-17 (CANL) - K154-16 (BAT)
K126-7 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Air conditioning amplifier assembly
K126-18 (CANL) - K154-16 (BAT)
K126-8 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Headlight ECU sub-assembly LH*1
K126-19 (CANL) - K154-16 (BAT)
K126-9 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Meter mirror sub-assembly*2
K126-20 (CANL) - K154-16 (BAT)
K126-10 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Multiplex tilt and telescopic ECU*3
K126-21 (CANL) - K154-16 (BAT)


·

*1: w/ Automatic Headlight Beam Level Control System

·

*2: w/ Headup Display System

·

*3: w/ Power Tilt and Power Telescopic System



Result:
Result Proceed to
OK A
NG (Line to No. 1 junction connector) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 JUNCTION CONNECTOR)
a.

Disconnect the R94 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C402513C61
3.646,1.333 4.135,1.573 0.49,0.24 0.271,1.375 0.708,1.604 0.438,0.229 1.042,0.729 1.208,0.729 1.208,0.729 1.208,1.427 true 1.042,2.115 1.208,2.115 1.208,2.115 1.208,1.698 true 6.104,2.135 5.938,2.135 5.938,2.135 5.938,1.719 true 1.365,0.552 1.531,0.552 1.531,0.552 1.531,1.438 true 1.875,0.542 1.708,0.542 1.708,0.542 1.708,1.427 true 1.385,2.26 1.552,2.26 1.552,2.26 1.552,1.677 true 1.885,2.26 1.719,2.26 1.719,2.26 1.719,1.677 true 0.24,0.167 0.552,0.365 0.313,0.198 10 false *a 3.719,0.188 4.031,0.385 0.313,0.198 10 false *1 3.74,1.365 4.115,1.563 0.375,0.198 10 false K154 0.385,1.417 0.76,1.615 0.375,0.198 10 false R94 0.365,0.646 1.104,0.906 0.74,0.26 10 false CANH*b*c 0.365,2.031 1,2.271 0.635,0.24 10 false CANL*b*c 0.844,2.188 1.479,2.427 0.635,0.24 10 false CANL*d 1.948,2.177 2.677,2.427 0.729,0.25 10 false CANL*e*f 0.802,0.479 1.438,0.719 0.635,0.24 10 false CANH*d 1.958,0.458 2.729,0.698 0.771,0.24 10 false CANH*e*f 6.177,2.063 6.552,2.26 0.375,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 Junction Connector)
*b to Outer Mirror Control ECU Assembly (for Driver Side)
(for LHD with Seat Position Memory System)
*c to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(for RHD with Seat Position Memory System)
*d to No. 3 CAN Junction Connector
*e to No. 5 Junction Connector
(for RHD)
*f to No. 6 CAN Junction Connector
(for LHD)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
R94-1 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Outer mirror control ECU assembly (for driver side)*1
R94-12 (CANL) - K154-16 (BAT)
R94-1 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Outer mirror control ECU assembly (for front passenger side)*2
R94-12 (CANL) - K154-16 (BAT)
R94-3 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 3 CAN junction connector
R94-14 (CANL) - K154-16 (BAT)
R94-4 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 5 junction connector*3
R94-15 (CANL) - K154-16 (BAT)
R94-4 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 6 junction connector*4
R94-15 (CANL) - K154-16 (BAT)


·

*1: for LHD with Seat Position Memory System

·

*2: for RHD with Seat Position Memory System

·

*3: for RHD

·

*4: for LHD



Result:
Result Proceed to
OK A
NG (Line to No. 3 CAN junction connector) B
NG (Line to No. 5 junction connector (for RHD)) C
NG (Line to No. 6 junction connector (for LHD)) D
NG (Line to ECU or sensor) E



A

REPLACE NO. 1 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

C

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 JUNCTION CONNECTOR)

D

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 JUNCTION CONNECTOR)

E

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
3.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 5 JUNCTION CONNECTOR)
a.

Disconnect the R100 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C402513C62
3.646,1.333 4.083,1.563 0.438,0.229 0.271,1.375 0.708,1.604 0.438,0.229 1.708,0.729 1.875,0.729 1.875,0.729 1.875,1.427 true 1.719,2.115 1.885,2.115 1.885,2.115 1.885,1.698 true 6.104,2.135 5.938,2.135 5.938,2.135 5.938,1.719 true 1.875,0.552 2.042,0.552 2.042,0.552 2.042,1.438 true 2.385,0.542 2.219,0.542 2.219,0.542 2.219,1.427 true 1.875,2.271 2.042,2.271 2.042,2.271 2.042,1.688 true 2.385,2.271 2.219,2.271 2.219,2.271 2.219,1.688 true 0.24,0.167 0.552,0.365 0.313,0.198 10 false *a 3.719,0.188 4.031,0.385 0.313,0.198 10 false *1 3.719,1.365 4.167,1.625 0.448,0.26 10 false K154 0.344,1.417 0.833,1.656 0.49,0.24 10 false R100 1.115,0.646 1.75,0.885 0.635,0.24 10 false CANH*b 1.167,2.042 1.802,2.281 0.635,0.24 10 false CANL*b 1.333,2.188 1.969,2.427 0.635,0.24 10 false CANL*c 2.469,2.177 3.198,2.427 0.729,0.25 10 false CANL*d 1.333,0.479 1.969,0.719 0.635,0.24 10 false CANH*c 2.469,0.458 3.24,0.698 0.771,0.24 10 false CANH*d 6.177,2.063 6.552,2.26 0.375,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 5 Junction Connector)
*b to No. 2 Junction Connector
*c to No. 1 Junction Connector *d to Position Control ECU Assembly RH
(w/ Seat Position Memory System)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
R100-5 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 2 junction connector
R100-16 (CANL) - K154-16 (BAT)
R100-6 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 1 junction connector
R100-17 (CANL) - K154-16 (BAT)
R100-7 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Position control ECU assembly RH*
R100-18 (CANL) - K154-16 (BAT)


*: w/ Seat Position Memory System



Result:
Result Proceed to
OK A
NG (Line to No. 1 junction connector) B
NG (Line to No. 2 junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 5 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 JUNCTION CONNECTOR)

D

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
4.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the R101 No. 6 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C402513C63
3.646,1.333 4.156,1.583 0.51,0.25 0.271,1.375 0.708,1.604 0.438,0.229 6.104,2.135 5.938,2.135 5.938,2.135 5.938,1.719 true 1.052,0.552 1.219,0.552 1.219,0.552 1.219,1.438 true 1.708,0.552 1.542,0.552 1.542,0.552 1.542,1.438 true 1.042,2.271 1.208,2.271 1.208,2.271 1.208,1.688 true 1.719,2.281 1.552,2.281 1.552,2.281 1.552,1.698 true 1.208,0.375 1.375,0.375 1.375,0.375 1.375,1.427 true 1.208,2.458 1.375,2.458 1.375,2.458 1.375,1.708 true 0.24,0.167 0.552,0.365 0.313,0.198 10 false *a 3.719,0.188 4.031,0.385 0.313,0.198 10 false *1 3.74,1.365 4.115,1.563 0.375,0.198 10 false K154 0.344,1.417 0.833,1.656 0.49,0.24 10 false R101 1.813,2.198 2.448,2.438 0.635,0.24 10 false CANL*d 0.49,2.188 1.219,2.438 0.729,0.25 10 false CANL*b 1.802,0.469 2.438,0.708 0.635,0.24 10 false CANH*d 0.469,0.469 1.24,0.708 0.771,0.24 10 false CANH*b 6.177,2.063 6.552,2.26 0.375,0.198 10 false BAT 0.656,0.292 1.292,0.531 0.635,0.24 10 false CANH*c 0.677,2.385 1.313,2.625 0.635,0.24 10 false CANL*c
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 Junction Connector)
*b to No. 2 Junction Connector
*c to No. 1 Junction Connector *d to Position Control ECU Assembly LH
(w/ Seat Position Memory System)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
R101-1 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 2 junction connector
R101-12 (CANL) - K154-16 (BAT)
R101-2 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 1 junction connector
R101-13 (CANL) - K154-16 (BAT)
R101-3 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Position control ECU assembly LH*
R101-14 (CANL) - K154-16 (BAT)


*: w/ Seat Position Memory System



Result:
Result Proceed to
OK A
NG (Line to No. 1 junction connector) B
NG (Line to No. 2 junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 6 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 JUNCTION CONNECTOR)

D

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
5.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 JUNCTION CONNECTOR)
a.

Disconnect the R97 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C402513C64
3.625,1.333 4.115,1.573 0.49,0.24 0.271,1.375 0.708,1.604 0.438,0.229 1.042,0.729 1.208,0.729 1.208,0.729 1.208,1.427 true 1.052,2.115 1.219,2.115 1.219,2.115 1.219,1.698 true 6.104,2.135 5.938,2.135 5.938,2.135 5.938,1.719 true 1.208,0.552 1.375,0.552 1.375,0.552 1.375,1.438 true 1.708,0.542 1.542,0.542 1.542,0.542 1.542,1.427 true 1.219,2.281 1.385,2.281 1.385,2.281 1.385,1.698 true 1.719,2.281 1.552,2.281 1.552,2.281 1.552,1.698 true 2.042,0.729 1.875,0.729 1.875,0.729 1.875,1.427 true 2.052,2.125 1.885,2.125 1.885,2.125 1.885,1.708 true 0.24,0.167 0.552,0.365 0.313,0.198 10 false *a 3.719,0.188 4.031,0.385 0.313,0.198 10 false *1 3.708,1.365 4.208,1.604 0.5,0.24 10 false K154 0.344,1.417 0.833,1.656 0.49,0.24 10 false R97 0.448,0.646 1.083,0.885 0.635,0.24 10 false CANH*b 0.49,2.042 1.125,2.281 0.635,0.24 10 false CANL*b 0.552,2.198 1.302,2.5 0.75,0.302 10 false CANL*c*d 1.802,2.208 2.531,2.458 0.729,0.25 10 false CANL*e*f 0.521,0.479 1.375,0.75 0.854,0.271 10 false CANH*c*d 1.792,0.469 2.563,0.708 0.771,0.24 10 false CANH*e*f 6.177,2.063 6.552,2.26 0.375,0.198 10 false BAT 2.135,0.646 2.906,0.885 0.771,0.24 10 false CANH*g 2.167,2.052 2.896,2.302 0.729,0.25 10 false CANL*g
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 2 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to No. 5 Junction Connector
(for RHD)
*d to No. 6 Junction Connector
(for LHD)
*e to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(for LHD with Seat Position Memory System)
*f to Outer Mirror Control ECU Assembly (for Driver Side)
(for RHD with Seat Position Memory System)
*g to Headlight ECU Sub-assembly RH
(w/ Automatic Headlight Beam Level Control System)
- -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
R97-1 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
R97-12 (CANL) - K154-16 (BAT)
R97-2 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 5 junction connector*1
R97-13 (CANL) - K154-16 (BAT)
R97-2 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 6 junction connector*2
R97-13 (CANL) - K154-16 (BAT)
R97-3 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Outer mirror control ECU assembly (for front passenger side)*3
R97-14 (CANL) - K154-16 (BAT)
R97-3 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Outer mirror control ECU assembly (for driver side)*4
R97-14 (CANL) - K154-16 (BAT)
R97-5 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Headlight ECU sub-assembly RH*5
R97-16 (CANL) - K154-16 (BAT)


·

*1: for RHD

·

*2: for LHD

·

*3: for LHD with Seat Position Memory System

·

*4: for RHD with Seat Position Memory System

·

*5: w/ Automatic Headlight Beam Level Control System



Result:
Result Proceed to
OK A
NG (Line to No. 5 junction connector (for RHD)) B
NG (Line to No. 6 junction connector (for LHD)) C
NG (Line to central gateway ECU (network gateway ECU)) D
NG (Line to ECU or sensor) E



A

REPLACE NO. 2 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

D

6.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

E

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
6.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the K76 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C402513C65
3.542,1.354 4.042,1.615 0.5,0.26 0.271,1.354 0.729,1.594 0.458,0.24 5.948,1.729 5.948,2.146 5.948,2.146 6.115,2.146 true 1.208,1.698 1.208,2.198 1.208,2.198 1.042,2.198 true 1.208,1.427 1.208,0.677 1.208,0.677 1.042,0.677 true 0.292,0.302 0.604,0.5 0.313,0.198 10 false *a 3.854,0.333 4.167,0.531 0.313,0.198 10 false *1 0.354,1.385 0.75,1.583 0.396,0.198 10 false R97 3.635,1.385 4.031,1.583 0.396,0.198 10 false K154 6.208,2.052 6.604,2.25 0.396,0.198 10 false BAT 0.469,0.604 1.115,0.854 0.646,0.25 10 false CANH*b 0.5,2.115 1.146,2.365 0.646,0.25 10 false CANL*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 2 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
R97-1 (CANH) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R97-12 (CANL) - K154-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C402517C19
1.594,0.198 2.01,0.469 0.417,0.271 4.927,0.302 5.458,0.583 0.531,0.281 1.875,2.49 2.01,2.49 2.01,2.49 2.01,1.406 true 6.021,2.156 5.854,2.156 5.854,2.156 5.854,1.677 true 2.271,2.49 2.104,2.49 2.104,2.49 2.104,1.406 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.698,0.25 2.01,0.448 0.313,0.198 10 false K76 1.49,2.417 2.042,2.615 0.552,0.198 10 false CA5L 6.135,2.083 6.688,2.281 0.552,0.198 10 false BAT 2.365,2.396 2.917,2.594 0.552,0.198 10 false CA5H 5.031,0.344 5.49,0.542 0.458,0.198 10 false K154 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
K76-15 (CA5H) - K154-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K76-16 (CA5L) - K154-16 (BAT)


HINT:
·

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR