Home › Engine / Hybrid System › A25A-FXS (INTAKE / EXHAUST) › EXHAUST PIPE › from 2019.10
RM33C0E _51 Engine / Hybrid System _065423 A25A-FXS INTAKE / EXHAUST _0322982 EXHAUST PIPE A

A25A-FXS INTAKE / EXHAUST  EXHAUST PIPE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front exhaust pipe assembly, center exhaust pipe assembly and tail exhaust pipe assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 17440 1.REMOVE TAIL EXHAUST PIPE ASSEMBLY LH

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A402307

Remove the 2 bolts and disconnect the tail exhaust pipe assembly LH from the center exhaust pipe assembly.


b.

Remove the tail exhaust pipe assembly LH from the 2 exhaust pipe supports.


c.

Remove the gasket from the center exhaust pipe assembly.


Hide 17420 2.REMOVE CENTER EXHAUST PIPE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A402308

Remove the 2 bolts and disconnect the center exhaust pipe assembly from the front exhaust pipe assembly.


b.

Remove the center exhaust pipe assembly from the 2 exhaust pipe supports.


c.

Remove the gasket from the front exhaust pipe assembly.


Hide 58166A 3.REMOVE FRONT FLOOR COVER LH (w/ Cover)

a.
A402309N01
2.219,0.083 2.354,0.24 0.135,0.156 10 true A 1.792,0.521 1.927,0.677 0.135,0.156 10 true A 1.833,1.448 1.969,1.604 0.135,0.156 10 true A 2.375,1.458 2.51,1.604 0.135,0.146 10 true A 2.75,0.417 2.896,0.583 0.146,0.167 10 true C 2.469,0.969 2.615,1.135 0.146,0.167 10 true C 1.177,0.021 1.323,0.188 0.146,0.167 10 true C 0.927,0.49 1.073,0.656 0.146,0.167 10 true C 0.719,1.021 0.865,1.188 0.146,0.167 10 true C 0.573,1.583 0.719,1.75 0.146,0.167 10 true B 1.906,1.823 2.052,1.99 0.146,0.167 10 true C

Remove the 3 bolts and 4 clips (A).


b.

Disengage the grommet (B) and 6 clips (C) to remove the front floor cover LH.


Hide 58165C 4.REMOVE FRONT FLOOR COVER RH (w/ Cover)

a.
A402310N01
2.26,0.052 2.385,0.208 0.125,0.156 10 true A 1.917,0.521 2.042,0.677 0.125,0.156 10 true A 0.646,0.917 0.771,1.073 0.125,0.156 10 true A 1.24,0.896 1.365,1.052 0.125,0.156 10 true A 1.75,1.823 1.885,1.979 0.135,0.156 10 true B 2.031,1.479 2.167,1.635 0.135,0.156 10 true C 2.479,1.052 2.615,1.208 0.135,0.156 10 true C 2.677,0.052 2.813,0.208 0.135,0.156 10 true C 1.333,0.052 1.469,0.208 0.135,0.156 10 true C 1.094,0.469 1.229,0.625 0.135,0.156 10 true C 0.521,1.344 0.656,1.5 0.135,0.156 10 true C

Remove the 3 bolts and 4 clips (A).


b.

Disengage the grommet (B) and 6 clips (C) to remove the front floor cover RH.


Hide 57533B 5.REMOVE FRONT CENTER FLOOR BRACE

a.
A402311

Remove the 4 bolts and front center floor brace from the vehicle body.


Hide 57523A 6.REMOVE CENTER FLOOR CROSSMEMBER BRACE

a.
A402312

Remove the 4 bolts and center floor crossmember brace from the vehicle body.


Hide 89467C 7.REMOVE AIR FUEL RATIO SENSOR (for Sensor 2)

Hide 17410 8.REMOVE FRONT EXHAUST PIPE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A402254

Remove the 2 nuts and disconnect the front exhaust pipe assembly from the exhaust manifold.


b.

Remove the front exhaust pipe assembly from the 2 exhaust pipe supports.


c.

Remove the gasket from the front exhaust pipe assembly.


Hide 17408 9.REMOVE TAIL EXHAUST PIPE BAFFLE SUB-ASSEMBLY

HINT:
·

Perform this procedure only when replacement of the tail exhaust pipe baffle sub-assembly is necessary.

·

If the tail exhaust pipe baffle sub-assembly is removed, replace it with a new one.



a.
A402316

Type A (w/ Tail Exhaust Pipe Baffle)

i.

Remove the tail exhaust pipe baffle sub-assembly.



b.
A402314

Type B

i.

Remove the tail exhaust pipe baffle sub-assembly.