Home › General › MAINTENANCE › OIL AND OIL FILTER › 2019.10–2020.08
RM33C0E _V1 General _065432 MAINTENANCE _0329955 OIL AND OIL FILTER A

MAINTENANCE  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

·

In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.



PROCEDURE

Hide 1.REMOVE CENTER NO. 4 ENGINE UNDER COVER

a.
A402129

Remove the 4 screws and center No. 4 engine under cover.


Hide 2.DRAIN ENGINE OIL

a.

Remove the oil filler cap sub-assembly.


b.

Remove the oil pan drain plug and gasket, and drain the engine oil into a container.


c.

Clean the oil pan drain plug.


d.

Install a new gasket to the oil pan drain plug.


e.

Install the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 15601 3.REMOVE OIL FILTER SUB-ASSEMBLY

a.

Using SST, remove the oil filter sub-assembly.

SST
09228-06502  


Hide 15601 4.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter sub-assembly installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter sub-assembly.


c.

Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.


d.

Using SST, tighten the oil filter sub-assembly.

SST
09228-06502  

i.

Depending on the work space available, choose from the following:

·

If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.


Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)

·

If not enough space is available to use a torque wrench, tighten the oil filter sub-assembly 3/4 of a turn by hand or using a common wrench.




Hide 5.ADD ENGINE OIL

a.

Destination package for Europe:

i.

Add new engine oil and install the oil filler cap sub-assembly.

Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)
API grade SN " Resource-Conserving"or SN PLUS "Resource-Conserving" multigrade engine oil
·

0W-16


API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or SN PLUS "Resource-Conserving", or ILSAC multigrade engine oil
·

0W-20

·

5W-30

·

10W-30


API grade SL, SM, SN or SN PLUS multigrade engine oil
·

15W-40



Standard Capacity:
Item Standard Condition
Drain and refill with oil filter change 4.5 liters (4.8 US qts, 4.0 Imp. qts)
Drain and refill without oil filter change 4.2 liters (4.4 US qts, 3.7 Imp. qts)
Dry fill 5.4 liters (5.7 US qts, 4.8 Imp. qts)

NOTICE:
·

When cleaning the No. 1 engine cover sub-assembly, do not use organic solvents such as brake cleaner as the No. 1 engine cover sub-assembly is made of urethane.

·

Make sure to use a neutral detergent when cleaning the No. 1 engine cover sub-assembly.





b.

except Europe:

i.

Add new engine oil and install the oil filler cap sub-assembly.

Standard Oil Grade(except GCC countries, Costa Rica, Chile, Jordan, Korea, Hong Kong, Taiwan and New Zealand):
Oil Grade Oil Viscosity (SAE)
API grade SN " Resource-Conserving"or SN PLUS "Resource-Conserving" multigrade engine oil
·

0W-16


API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or SN PLUS "Resource-Conserving", or ILSAC multigrade engine oil
·

0W-20

·

5W-20

·

5W-30

·

10W-30


API grade SL, SM, SN or SN PLUS multigrade engine oil
·

15W-40

·

20W-50



Standard Oil Grade(for GCC countries, Costa Rica, Chile, Jordan, Korea, Hong Kong, Taiwan and New Zealand):
Oil Grade Oil Viscosity (SAE)
API grade SN " Resource-Conserving"or SN PLUS "Resource-Conserving" multigrade engine oil
·

0W-16


API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or SN PLUS "Resource-Conserving", or ILSAC multigrade engine oil
·

0W-20

·

5W-20

·

5W-30

·

10W-30


API grade SL, SM, SN or SN PLUS multigrade engine oil
·

15W-40



Standard Capacity:
Item Standard Condition
Drain and refill with oil filter change 4.5 liters (4.8 US qts, 4.0 Imp. qts)
Drain and refill without oil filter change 4.2 liters (4.4 US qts, 3.7 Imp. qts)
Dry fill 5.4 liters (5.7 US qts, 4.8 Imp. qts)

NOTICE:
·

When cleaning the No. 1 engine cover sub-assembly, do not use organic solvents such as brake cleaner as the No. 1 engine cover sub-assembly is made of urethane.

·

Make sure to use a neutral detergent when cleaning the No. 1 engine cover sub-assembly.





Hide 6.INSPECT FOR ENGINE OIL LEAK

a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 3103

e.

Start the engine. Make sure that there are no engine oil leaks from the area that was worked on.


Hide 8.INSTALL CENTER NO. 4 ENGINE UNDER COVER

a.

Install the center No. 4 engine under cover with the 4 screws.