Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM (w/ Vehicle Approaching Speaker Switch) › 2019.10–2020.08
RM33C0E _59 Vehicle Exterior _074891 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0363660 VEHICLE PROXIMITY NOTIFICATION SYSTEM(w/ Vehicle Approaching Speaker Switch) J

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM(w/ Vehicle Approaching Speaker Switch)  The Sound does not Stop when The Engine is Operated or when The Shift Lever is in P  


DESCRIPTION

The vehicle approaching speaker controller receives "permission signals*" from hybrid vehicle control ECU assembly, and produces the warning sound from the vehicle approaching speaker assembly.

HINT:

*: Permission signals

·

Vehicle proximity notification system operation permitted (engine is stopped and shift lever is not in P).

·

Vehicle proximity notification system operation prohibited (engine is operating or shift lever is in P).



WIRING DIAGRAM

E369726E07
0.885,1.531 1.198,1.729 0.313,0.198 10 false K69 0.875,1.708 3.323,1.948 2.448,0.24 10 false Hybrid Vehicle Control ECU Assembly 2.281,0.781 2.677,0.979 0.396,0.198 10 false KOK 2.698,0.781 3.01,0.979 0.313,0.198 10 false 7 4.792,1.625 5.198,1.823 0.406,0.198 10 false K160 4.792,1.802 6.115,2.25 1.323,0.448 10 false Vehicle Approaching Speaker Controller 4.938,0.792 5.333,0.99 0.396,0.198 10 false KOK 4.677,0.792 4.99,0.99 0.313,0.198 10 false 11 4.74,1.198 5.052,1.396 0.313,0.198 10 false 7 4.938,1.323 5.333,1.521 0.396,0.198 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the hybrid vehicle control ECU assembly, refer to Service Bulletin.


PROCEDURE

1.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Connect the GTS the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Vehicle Proximity Notification System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Permission Signal Vehicle proximity notification system permission signal OFF or ON OFF: Vehicle proximity notification system operation prohibited (engine is operating or shift lever is in P).
ON: Vehicle proximity notification system operation permitted (engine is stopped and shift lever is not in P).
-
Body Electrical > Vehicle Proximity Notification System > Data List
Tester Display
Permission Signal
50003 359 8

Result:
Result Proceed to
The GTS display changes according to the engine status or the shift lever position A
The GTS display does not change according to the engine status or the shift lever position B



A

B

3.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER (PERMISSION SIGNAL)
3.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER (PERMISSION SIGNAL)
E195974C69
1.469,0.292 1.875,0.51 0.406,0.219 0.99,1.813 1.427,1.427 true 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a 1.51,0.323 2.135,0.865 0.625,0.542 10 false K160 0.802,1.865 1.115,2.063 0.313,0.198 10 false KOK
*a Component with harness connected
(Vehicle Approaching Speaker Controller)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K160-11 (KOK) - Body ground Power switch on (READY), shift lever in P Below 2.3 V
Power switch on (READY), engine stopped and shift lever not in P 8 V or higher



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - VEHICLE APPROACHING SPEAKER CONTROLLER)
4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - VEHICLE APPROACHING SPEAKER CONTROLLER)
a.

Disconnect the K69 hybrid vehicle control ECU assembly connector.


b.

Disconnect the K160 vehicle approaching speaker controller connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K69-7 (KOK) - K160-11 (KOK) Always Below 1 Ω
K69-7 (KOK) or K160-11 (KOK) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER
a.

Replace the vehicle approaching speaker controller with a new or known good one.

Click hereVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER ECU>REMOVAL

OK:

The operation of the vehicle proximity notification system returns to normal.



Result:
Proceed to
OK
NG



OK

END (VEHICLE APPROACHING SPEAKER CONTROLLER WAS DEFECTIVE)

NG

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY