Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM (w/ Vehicle Approaching Speaker Switch) › 2019.10–2020.08
RM33C0E _59 Vehicle Exterior _074891 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0363660 VEHICLE PROXIMITY NOTIFICATION SYSTEM(w/ Vehicle Approaching Speaker Switch) J

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM(w/ Vehicle Approaching Speaker Switch)  Communication between Vehicle Proximity Notification System and Diagnostic Tool is not Possible  


DESCRIPTION

The vehicle approaching speaker controller communicates with the GTS through the DLC3.

WIRING DIAGRAM

E276443E17
0.521,0.583 2,0.865 1.479,0.281 10 false from IG1-NO. 1 Relay 3.385,0.729 4.406,0.958 1.021,0.229 10 false ECU-IG1 NO. 3 4.656,2.271 7.146,2.51 2.49,0.24 10 false Vehicle Approaching Speaker Controller 4.656,2.094 5.677,2.323 1.021,0.229 10 false K160 5.677,0.583 5.906,0.802 0.229,0.219 10 false IG 5.469,0.448 5.698,0.667 0.229,0.219 10 false 1 5.677,1.375 6.146,1.594 0.469,0.219 10 false PRST 5.677,1.729 6.146,1.948 0.469,0.219 10 false GND 5.469,1.26 5.698,1.479 0.229,0.219 10 false 9 5.469,1.615 5.698,1.833 0.229,0.219 10 false 7 1.281,2.073 1.75,2.292 0.469,0.219 10 false K154 1.719,2.073 2.188,2.292 0.469,0.219 10 false DLC3 2.021,1.375 2.281,1.594 0.26,0.219 10 false SIL 2.021,1.75 2.281,1.969 0.26,0.219 10 false CG 2.344,1.26 2.573,1.479 0.229,0.219 10 false 7 2.344,1.635 2.573,1.854 0.229,0.219 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

The vehicle approaching speaker controller and GTS communicate using SIL communication.


PROCEDURE

1.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Health Check.


Result:
Result Proceed to
Communication with the vehicle approaching speaker controller is not possible A
Communication with the vehicle approaching speaker controller is possible B



A

2.CHECK HARNESS AND CONNECTOR (IG POWER SOURCE - VEHICLE APPROACHING SPEAKER CONTROLLER)

B

2.CHECK HARNESS AND CONNECTOR (IG POWER SOURCE - VEHICLE APPROACHING SPEAKER CONTROLLER)
a.

Disconnect the K160 vehicle approaching speaker controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K160-1 (IG) - Body ground Power switch on (IG) 11 to 14 V
K160-1 (IG) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K160-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (DLC3 - VEHICLE APPROACHING SPEAKER CONTROLLER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DLC3 - VEHICLE APPROACHING SPEAKER CONTROLLER)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K154-7 (SIL) - K160-9 (PRST) Always Below 1 Ω
K154-7 (SIL) or K160-9 (PRST) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K154-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR