Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2020.08
RM33C0E _59 Vehicle Exterior _065469 DOOR / HATCH _0333680 FRONT DOOR N

DOOR / HATCH  FRONT DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B471672C01
0.708,0.083 1.021,0.24 0.313,0.156 10 false *a 2.479,0.083 2.792,0.24 0.313,0.156 10 false *b
*a Centering Bolt
*b Standard Bolt


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

Centering bolts are used to install the door hinges to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

The specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1.INSPECT FRONT DOOR

a.

Check that the clearance measurements of areas a through m are within each standard range.

B471481N01
0.552,1.479 0.708,1.677 0.156,0.198 10 false a 0.427,2.115 0.583,2.313 0.156,0.198 10 false b 1.583,0.104 1.74,0.302 0.156,0.198 10 false c 1.26,0.865 1.417,1.063 0.156,0.198 10 false d 3.052,0.115 3.208,0.313 0.156,0.198 10 false e 2.792,0.927 2.948,1.125 0.156,0.198 10 false f 4.563,0.115 4.719,0.313 0.156,0.198 10 false g 4.313,0.917 4.469,1.115 0.156,0.198 10 false h 6.271,1.083 6.427,1.281 0.156,0.198 10 false i 5.802,3.667 5.958,3.865 0.156,0.198 10 false j 3.365,4.323 3.521,4.521 0.156,0.198 10 false k 1.583,4.521 1.74,4.719 0.156,0.198 10 false l 1.156,4.469 1.313,4.667 0.156,0.198 10 false m

Standard Clearance
Area Measurement Area Measurement
a 3.3 to 6.7 mm (0.130 to 0.264 in.) b 3.5 to 7.5 mm (0.138 to 0.295 in.)
c 3.3 to 6.7 mm (0.130 to 0.264 in.) d 0.2 to 4.2 mm (0.0079 to 0.165 in.)
e 3.3 to 6.7 mm (0.130 to 0.264 in.) f 1.2 to 5.2 mm (0.0472 to 0.205 in.)
g 3.3 to 6.7 mm (0.130 to 0.264 in.) h 1.1 to 5.1 mm (0.0433 to 0.201 in.)
i 2.3 to 6.3 mm (0.0906 to 0.248 in.) j 4.1 mm (0.161 in.)
k 5.3 mm (0.209 in.) l 2.6 to 5.0 mm (0.102 to 0.197 in.)
m -1.2 to 1.2 mm (-0.0472 to 0.0472 in.) - -


Hide 2.ADJUST FRONT DOOR

NOTICE:

Make sure to turn the power switch off before adjusting the door lock strikers.


a.
B471479

Using SST, loosen the 4 hinge bolts on the vehicle body and adjust the door position.

SST
09812-00020  


b.

Tighten the 4 hinge bolts on the vehicle body after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the 4 hinge bolts on the door and adjust the door position.


d.

Tighten the 4 hinge bolts on the door after adjustment.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.
B471480

Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.


f.

Using a brass bar and a hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)