Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442440 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  P056014  System Voltage (BATT) Circuit Short to Ground or Open  


DESCRIPTION

Auxiliary battery power is supplied to the BATT terminal of the hybrid vehicle control ECU assembly in order to store DTCs and freeze frame data. Even if the power switch is turned off, back-up power is supplied.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P056014 System Voltage (BATT) Circuit Short to Ground or Open Malfunction in the hybrid vehicle control ECU assembly back-up power source circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU assembly

·

Fuse


Comes on Master Warning Light:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A396204E05
1,2.219 2.948,2.833 1.948,0.615 10 false Auxiliary Battery 1.188,1.302 2.021,1.469 0.833,0.167 10 false MAIN 2.333,1.302 2.979,1.479 0.646,0.177 10 false J/B-B 3.521,1.302 4.677,1.906 1.156,0.604 10 false ECU-B NO. 2 5.677,1.146 6.094,1.333 0.417,0.188 10 false BATT 5.677,1.74 6.01,1.917 0.333,0.177 10 false E1 5.25,2.854 6.969,3.313 1.719,0.458 10 false Hybrid Vehicle Control ECU Assembly 5.333,1.729 5.667,1.906 0.333,0.177 10 false K69 5.333,1.146 5.667,1.323 0.333,0.177 10 false K70 5.396,0.927 5.771,1.229 0.375,0.302 10 false 3 5.396,1.51 5.552,1.708 0.156,0.198 10 false 6 2.281,1 2.438,1.198 0.156,0.198 10 false 1 4.052,1 4.208,1.198 0.156,0.198 10 false 2 3.656,1 3.813,1.198 0.156,0.198 10 false 1 2.677,1 2.833,1.198 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)
a.
A414384C02
2.542,0.813 2.917,1.031 0.375,0.219 2.563,1.125 2.917,1.333 0.354,0.208 2.542,0.49 2.917,0.708 0.375,0.219 2.552,1.49 2.917,1.698 0.365,0.208 2.104,2.823 2.448,3.01 0.344,0.188 2.104,3.115 2.448,3.313 0.344,0.198 2.115,3.427 2.448,3.625 0.333,0.198 2.115,3.719 2.448,3.906 0.333,0.188 0.198,0.104 0.583,0.323 0.385,0.219 12 false *A 0.188,2.458 0.573,2.677 0.385,0.219 12 false *B 2.573,0.51 2.885,0.688 0.313,0.177 10 true K70 2.583,0.823 2.896,1.01 0.313,0.188 10 true K69 2.583,1.135 2.896,1.302 0.313,0.167 10 true A29 2.573,1.5 2.906,1.677 0.333,0.177 10 true A28 2.135,2.833 2.438,3 0.302,0.167 10 true K70 2.115,3.125 2.438,3.292 0.323,0.167 10 true K69 2.125,3.438 2.427,3.604 0.302,0.167 10 true A29 2.135,3.729 2.427,3.896 0.292,0.167 10 true A28
*A for LHD
*B for RHD


Check the connector connections and contact pressure of the relevant terminals for the hybrid vehicle control ECU assembly connectors.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

CONNECT SECURELY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Turn the power switch off.


b.
A389500C67
1.802,0.833 2.302,1.083 0.5,0.25 2.375,0.833 2.875,1.083 0.5,0.25 1.667,2.417 1.813,1.719 true 2.917,2.417 2.708,1.719 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.573,2.479 1.885,2.635 0.313,0.156 10 false E1 2.833,2.49 3.396,2.656 0.563,0.167 10 false BATT 1.958,0.885 2.292,1.052 0.333,0.167 10 false K69 2.531,0.885 2.865,1.052 0.333,0.167 10 false K70
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K70-3 (BATT) - K69-6 (E1) Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

3.CHECK FUSE (ECU-B NO. 2)
3.CHECK FUSE (ECU-B NO. 2)
a.
A373223C04
0.74,1.583 1.052,0.99 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *1 1.104,0.885 1.417,1.083 0.313,0.198 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 ECU-B NO. 2 Fuse


Remove the ECU-B NO. 2 fuse from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-B NO. 2 fuse Always Below 1 Ω



c.

Reinstall the ECU-B NO. 2 fuse.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECU-B NO. 2 FUSE - AUXILIARY BATTERY TERMINAL)

NG

REPLACE FUSE (ECU-B NO. 2)

4.CHECK HARNESS AND CONNECTOR (ECU-B NO. 2 FUSE - AUXILIARY BATTERY TERMINAL)
a.
A373224C04
0.208,0.698 0.521,0.896 0.313,0.198 10 false *2 0.083,0.073 0.396,0.271 0.313,0.198 10 false *1
*1 Instrument Panel Junction Block Assembly
*2 ECU-B NO. 2 Fuse


Remove the ECU-B NO. 2 fuse from the instrument panel junction block assembly.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the cable from the positive (+) auxiliary battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-B NO. 2 fuse terminal 1 - Auxiliary battery positive (+) cable Power switch off Below 1 Ω
ECU-B NO. 2 fuse terminal 1 - Body ground Power switch off 10 kΩ or higher



e.

Connect the cable to the positive (+) auxiliary battery terminal.


f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Install the ECU-B NO. 2 fuse.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECU-B NO. 2 FUSE - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECU-B NO. 2 FUSE - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Remove the ECU-B NO. 2 fuse from the instrument panel junction block assembly.


b.

Disconnect the K70 hybrid vehicle control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

A407378C05
5.667,0.292 6.031,0.531 0.365,0.24 6.26,2.208 5.958,1.719 true 0.458,0.24 0.771,0.438 0.313,0.198 10 false *1 0.688,0.74 1,0.938 0.313,0.198 10 false *2 3.635,0.229 3.948,0.427 0.313,0.198 10 false *a 6.323,2.167 6.74,2.406 0.417,0.24 10 false BATT 5.74,0.354 6.052,0.552 0.313,0.198 10 false K70
*1 Instrument Panel Junction Block Assembly *2 ECU-B NO. 2 Fuse
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
ECU-B NO. 2 fuse terminal 2 - K70-3 (BATT) Power switch off Below 1 Ω



d.

Reconnect the K70 hybrid vehicle control ECU assembly connector.


e.

Install the ECU-B NO. 2 fuse.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR