Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442440 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  P070562  Transmission Range Sensor "A" Circuit (PRNDL Input) Signal Compare Failure  


DESCRIPTION

The shift lever position sensor sends 7 different switch signals to the hybrid vehicle control ECU assembly. The hybrid vehicle control ECU assembly uses these signals to detect the shift lever position (P, R, N or D). The hybrid vehicle control ECU assembly also uses this information to determine the intended direction of travel (forward or reverse).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P070562 Transmission Range Sensor "A" Circuit (PRNDL Input) Signal Compare Failure Shift sensor circuit malfunction (abnormal pattern)
A malfunction in the P, R, N or D circuit is detected based on the shift sensor input pattern.
(1 trip detection logic)
·

Wire harness or connector

·

Shift lever position sensor

·

Hybrid vehicle control ECU assembly


Does not come on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P070562
·

Shift Position

·

Shift Position Sensor (PNB)

·

Shift Position Sensor (PR)

·

Shift Position Sensor (DB1)

·

Shift Position Sensor (DB2)

·

Shift Position Sensor (N)

·

Shift Position Sensor (R)

·

Shift Position Sensor (P)



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Slowly move the shift lever from P to S then back to P.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A407614E02
0.552,4 1.229,4.51 0.677,0.51 10 false n1 0.521,4.156 2.99,4.469 2.469,0.313 10 false Shift Lever Position Sensor 1.896,0.583 2.208,0.781 0.313,0.198 10 false +B 1.969,1.083 2.281,1.281 0.313,0.198 10 false P 1.958,1.438 2.271,1.635 0.313,0.198 10 false R 1.969,1.813 2.281,2.01 0.313,0.198 10 false N 1.844,2.135 2.156,2.333 0.313,0.198 10 false DB1 1.896,2.823 2.208,3.021 0.313,0.198 10 false PR 1.833,3.198 2.146,3.396 0.313,0.198 10 false PNB 1.833,2.479 2.146,2.677 0.313,0.198 10 false DB2 2.188,0.583 2.5,0.781 0.313,0.198 10 false 7 2.208,1.083 2.521,1.281 0.313,0.198 10 false 8 2.208,1.438 2.521,1.635 0.313,0.198 10 false 9 2.198,1.813 2.51,2.01 0.313,0.198 10 false 2 2.198,2.135 2.51,2.333 0.313,0.198 10 false 1 2.198,2.479 2.51,2.677 0.313,0.198 10 false 6 2.208,2.813 2.521,3.01 0.313,0.198 10 false 3 2.198,3.198 2.51,3.396 0.313,0.198 10 false 4 4.615,0.573 4.927,0.771 0.313,0.198 10 false 1 4.563,1.073 4.875,1.271 0.313,0.198 10 false 21 4.563,1.427 4.875,1.625 0.313,0.198 10 false 15 4.552,1.813 4.865,2.01 0.313,0.198 10 false 20 4.542,2.125 4.854,2.323 0.313,0.198 10 false 26 4.542,2.479 4.854,2.677 0.313,0.198 10 false 14 4.542,2.802 4.854,3 0.313,0.198 10 false 17 4.552,3.177 4.865,3.375 0.313,0.198 10 false 34 4.865,0.688 5.469,0.917 0.604,0.229 10 false PSFT 4.844,1.073 5.448,1.302 0.604,0.229 10 false P 4.844,1.417 5.156,1.615 0.313,0.198 10 false R 4.833,1.802 5.146,2 0.313,0.198 10 false N 4.833,2.125 5.146,2.323 0.313,0.198 10 false DB1 4.823,2.458 5.135,2.656 0.313,0.198 10 false DB2 4.823,2.802 5.135,3 0.313,0.198 10 false PR 4.813,3.167 5.125,3.365 0.313,0.198 10 false PNB 4.74,4.031 5.417,4.5 0.677,0.469 10 false A29 4.771,4.198 7.156,4.698 2.385,0.5 10 false Hybrid Vehicle Control ECU Assembly

PROCEDURE

1.READ VALUE USING GTS (SHIFT POSITION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Shift Position Sensor (PNB), Shift Position Sensor (PR), Shift Position Sensor (DB1), Shift Position Sensor (DB2), Shift Position Sensor (N), Shift Position Sensor (R) and Shift Position Sensor (P).


d.

While slowly moving the shift lever from P to S, then back to P, read the Data List (Shift Position Sensor) displayed on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display
Shift Position Sensor (PNB)
Shift Position Sensor (PR)
Shift Position Sensor (DB1)
Shift Position Sensor (DB2)
Shift Position Sensor (N)
Shift Position Sensor (R)
Shift Position Sensor (P)
50003 397 400,401,403,402,404,405,406
HINT:

Be sure to move the shift lever slowly.


Standard:
Data List Shift Position
P R N D or S
Shift Position Sensor (P) ON OFF OFF OFF
Shift Position Sensor (R) OFF ON OFF OFF
Shift Position Sensor (PR) ON ON OFF OFF
Shift Position Sensor (N) OFF OFF ON OFF
Shift Position Sensor (DB1) OFF OFF OFF ON
Shift Position Sensor (DB2) OFF OFF OFF ON
Shift Position Sensor (PNB) ON OFF ON OFF



e.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
OK:

DTC P070562 is not output.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK FOR INTERMITTENT PROBLEMS

NG

3.INSPECT SHIFT LEVER POSITION SENSOR
2.CHECK FOR INTERMITTENT PROBLEMS

OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

3.INSPECT SHIFT LEVER POSITION SENSOR
a.

Turn the power switch on (IG).


b.
A389500C79
1.177,0.417 1.677,0.667 0.5,0.25 1.583,2.573 1.615,1.854 true 2.083,2.583 1.667,1.854 true 0.833,2.5 1.198,1.833 true 1.167,2.5 1.208,1.906 true 1.25,1.781 0.76,1.01 true 1.344,1.771 1.167,1.01 true 1.396,1.771 1.667,1.021 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.542,2.625 1.854,2.781 0.313,0.156 10 false P 2.073,2.625 2.25,2.823 0.177,0.198 10 false N 1.031,2.542 1.427,2.708 0.396,0.167 10 false PNB 0.615,2.531 1.01,2.698 0.396,0.167 10 false DB1 0.51,0.875 0.906,1.042 0.396,0.167 10 false PR 1.031,0.844 1.427,1.01 0.396,0.167 10 false R 1.729,0.844 2.125,1.01 0.396,0.167 10 false DB2 1.302,0.458 1.698,0.625 0.396,0.167 10 false A29
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A29-21 (P) - Body ground Power switch on (IG)
Shift lever in P
6.0 to 14 V
Power switch on (IG)
Shift lever in any position except P
0 to 1.5 V
A29-15 (R) - Body ground Power switch on (IG)
Shift lever in R
6.0 to 14 V
Power switch on (IG)
Shift lever in any position except R
0 to 1.5 V
A29-17 (PR) - Body ground Power switch on (IG)
Shift lever in P or R
6.0 to 14 V
Power switch on (IG)
Shift lever in any position except P or R
0 to 1.5 V
A29-20 (N) - Body ground Power switch on (IG)
Shift lever in N
6.0 to 14 V
Power switch on (IG)
Shift lever in any position except N
0 to 1.5 V
A29-26 (DB1) - Body ground Power switch on (IG)
Shift lever in D or S
6.0 to 14 V
Power switch on (IG)
Shift lever in any position except D or S
0 to 1.5 V
A29-14 (DB2) - Body ground Power switch on (IG)
Shift lever in D or S
6.0 to 14 V
Power switch on (IG)
Shift lever in any position except D or S
0 to 1.5 V
A29-34 (PNB) - Body ground Power switch on (IG)
Shift lever in P or N
6.0 to 14 V
Power switch on (IG)
Shift lever in any position except P or N
0 to 1.5 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
A405841N09
0.51,0.823 0.802,1.042 0.292,0.219 0.542,0.844 0.781,1.021 0.24,0.177 10 true n1

Disconnect the n1 shift lever position sensor connector.


b.

Turn the power switch on (IG).


c.
A373228C07
1.49,0.198 1.854,0.479 0.365,0.281 1.948,1.74 1.698,1.313 true 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 1.583,0.281 1.896,0.479 0.313,0.198 10 false n1 1.927,1.781 2.24,1.979 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Shift Lever Position Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
n1-7 (+B) - Body ground Power switch on (IG) 6.0 to 14 V


NOTICE:

Turning the power switch on (IG) with the shift lever position sensor connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Reconnect the n1 shift lever position sensor connector.


Result:
Proceed to
OK
NG



OK

5.INSPECT SHIFT LEVER POSITION SENSOR

NG

6.CHECK HARNESS AND CONNECTOR (SHIFT LEVER POSITION SENSOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
5.INSPECT SHIFT LEVER POSITION SENSOR
a.
A405841N09
0.51,0.823 0.802,1.042 0.292,0.219 0.542,0.844 0.781,1.021 0.24,0.177 10 true n1

Disconnect the n1 shift lever position sensor connector.


b.
A264044C36
0.229,1.104 0.594,1.385 0.365,0.281 1.969,1.469 2.188,1.844 true 1.719,1.469 1.792,1.906 true 1.49,1.469 1.458,1.875 true 1.323,1.469 1.188,1.833 true 1.26,1.125 0.927,0.771 true 1.406,1.094 1.26,0.479 true 1.594,1.104 1.656,0.458 true 1.865,1.104 2.063,0.5 true 0.146,0.115 0.583,0.448 0.438,0.333 10 false *a 0.677,0.604 1.115,0.885 0.438,0.281 10 false PNB 1.135,0.323 1.5,0.625 0.365,0.302 10 false PR 1.635,0.281 1.948,0.583 0.313,0.302 10 false N 1.99,0.333 2.344,0.604 0.354,0.271 10 false DB1 2.146,1.896 2.594,2.094 0.448,0.198 10 false DB2 1.708,1.958 2.021,2.156 0.313,0.198 10 false +B 1.396,1.938 1.667,2.146 0.271,0.208 10 false P 1.115,1.875 1.375,2.073 0.26,0.198 10 false R 0.302,1.156 0.656,1.396 0.354,0.24 10 false n1
*a Component without harness connected
(Shift Lever Position Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
n1-7 (+B) - n1-3 (PR) Shift lever in P Below 1 Ω
n1-7 (+B) - n1-4 (PNB) Below 1 Ω
n1-7 (+B) - n1-8 (P) Below 1 Ω
n1-7 (+B) - n1-1 (DB1), n1-2 (N), n1-6 (DB2) and n1-9 (R) 10 kΩ or higher
n1-7 (+B) - n1-3 (PR) Shift lever in R Below 1 Ω
n1-7 (+B) - n1-9 (R) Below 1 Ω
n1-7 (+B) - n1-1 (DB1), n1-2 (N), n1-4 (PNB), n1-6 (DB2) and n1-8 (P) 10 kΩ or higher
n1-7 (+B) - n1-2 (N) Shift lever in N Below 1 Ω
n1-7 (+B) - n1-4 (PNB) Below 1 Ω
n1-7 (+B) - n1-1 (DB1), n1-3 (PR), n1-6 (DB2), n1-8 (P) and n1-9 (R) 10 kΩ or higher
n1-7 (+B) - n1-1 (DB1) Shift lever in D or S Below 1 Ω
n1-7 (+B) - n1-6 (DB2) Below 1 Ω
n1-7 (+B) - n1-2 (N), n1-3 (PR), n1-4 (PNB), n1-8 (P) and n1-9 (R) 10 kΩ or higher


HINT:

Terminals No. 5 on the component side connector is empty.



c.

Reconnect the n1 shift lever position sensor connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

6.CHECK HARNESS AND CONNECTOR (SHIFT LEVER POSITION SENSOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the n1 shift lever position sensor connector.


b.

Disconnect the A29 hybrid vehicle control ECU assembly connector.


c.
A373229C07
1.49,0.198 1.844,0.469 0.354,0.271 0.521,3.594 0.875,3.865 0.354,0.271 1.667,3.635 2.021,3.74 true 1.698,1.24 1.76,1.656 true 0.573,3.656 0.885,3.854 0.313,0.198 10 false A29 0.198,1.917 0.51,2.115 0.313,0.198 10 false *b 1.563,0.26 1.875,0.458 0.313,0.198 10 false n1 2.073,3.708 2.583,4.021 0.51,0.313 10 false PSFT 1.698,1.677 2.208,1.99 0.51,0.313 10 false +B 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Shift Lever Position Sensor)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
n1-7 (+B) - A29-1 (PSFT) Power switch off Below 1 Ω
n1-7 (+B) or A29-1 (PSFT) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the A29 hybrid vehicle control ECU assembly connector.


e.

Reconnect the n1 shift lever position sensor connector.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR