Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442441 MOTOR GENERATOR CONTROL SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for LITHIUM-ION BATTERY)  P0C3D1C  DC/DC Converter Temperature Sensor "B" Circuit Voltage Out of Range  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs indicate that the boost converter temperature sensor (lower) value is abnormal. The cause of this malfunction may be one of the following:

Internal inverter malfunction

Inverter with converter assembly internal circuit malfunction


Hybrid cooling system malfunction

Coolant circulation abnormal (frozen or leaking, etc.)


Inverter low-voltage circuit malfunction

The connectors are not connected properly



DESCRIPTION

The motor generator control ECU, which is built into in the inverter with converter assembly, detects the temperature of the boost converter using a temperature sensor built into the boost converter. If necessary, the motor generator control ECU will limit inverter output to help prevent the boost converter from overheating. The motor generator control ECU also detects malfunctions in the sensor based on the temperature sensor values.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0C3D1C DC/DC Converter Temperature Sensor "B" Circuit Voltage Out of Range The actual boost converter temperature (lower) high and the difference between the estimated boost converter temperature (lower) and the actual temperature exceeds a threshold for 10 seconds, or after a long soak, the boost converter temperature (lower) sensor value differs from the values of other sensors.
(1 trip detection logic)
·

Inverter cooling system

·

Cooling fan system

·

Inverter with converter assembly

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0C3D1C
·

Boosting Converter Temperature 1 (Lower)

·

Inverter Coolant Temperature



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch on (READY), shift lever in D, while depressing the brake pedal with the vehicle stopped, depress the accelerator pedal.

5.

After the engine starts, release the accelerator pedal and wait for the engine to stop.

6.

Turn the power switch off and wait for 5 hours or more.

NOTICE:

Make sure that the temperature of the inverter coolant do not drop below 15°C (59°F).


7.

Turn the power switch on (IG) and within 3 seconds or less, turn the power switch on (READY) and wait 10 seconds or more.

HINT:

It is possible to turn the power switch on (READY) without turning it on (IG) first.


8.

Turn the GTS on.

9.

Drive the vehicle for approximately 10 minutes with the value of Data List item "Inverter Coolant Temperature" 25°C (77°F) or more.

10.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

11.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358


·

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C05
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0C3D1C only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs are also output. B


Table 1
Malfunction Content Relevant DTC
Insulation Malfunction P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure
P1C7D49 Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure
P1C7E49 Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure
P1C7F49 Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure

Table 2
Malfunction Content Relevant DTC
Sensor and actuator circuit malfunction P0C7396 Motor Electronics Coolant Pump "A" Component Internal Failure
P314A31 Motor Electronics Coolant Pump "A" No Signal
System malfunction P0A9300 Inverter "A" Cooling System Performance

HINT:

P0C3D1C may be output as a result of the malfunction indicated by the DTCs above.

1.

The chart above is listed in inspection order of priority.

2.

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)




e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY)>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK COOLING SYSTEM

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK COOLING SYSTEM

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>Cooling System

HINT:

If the "Cooling System" inspection results are normal, perform the next step.


Result:
Proceed to
NEXT



NEXT

REPLACE INVERTER WITH CONVERTER ASSEMBLY