Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2020.08
RM33C0E _51 Engine / Hybrid System _065433 HYBRID / BATTERY CONTROL _0442440 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  P253012  IG2 Signal Circuit Short to Auxiliary Battery  


DESCRIPTION

The hybrid vehicle control ECU assembly compares the IG2 signal to the IG control status signal sent from the certification ECU (smart key ECU assembly) to detect a stuck on malfunction of the IG2 signal.

HINT:

If DTC P253012 is stored, the power switch will turn off (READY off).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P253012 IG2 Signal Circuit Short to Auxiliary Battery The IG2 signal of the hybrid vehicle control ECU assembly and the IG control status signal sent from the certification ECU (smart key ECU assembly) do not match.
(1 trip detection logic)
·

Auxiliary battery

·

Certification ECU (smart key ECU assembly)

·

Hybrid vehicle control ECU assembly

·

ECM

·

IG2 NO. 1 relay

·

Wire harness or connector


Does not come on Master Warning Light:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and wait for 15 seconds or more.

6.

Turn the power switch off and wait for 2 minutes or more.

7.

Turn the power switch on (IG) and turn the GTS on.

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A406711E05
0.083,0.51 0.948,1.042 0.865,0.531 10 false from Auxiliary Battery 1.333,0.708 2.031,0.906 0.698,0.198 10 false IG2-MAIN 2.49,1.302 3.406,1.5 0.917,0.198 10 false IG2 NO. 1 3.344,0.708 4.698,1.01 1.354,0.302 10 false ECU-IG2 NO. 1 2.052,1.75 4.344,2.24 2.292,0.49 10 false No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly 5.26,4.219 7.104,4.573 1.844,0.354 10 false Certification ECU (Smart Key ECU Assembly) 5.25,4.073 5.552,4.302 0.302,0.229 10 false K62 5.74,2.865 6.042,3.094 0.302,0.229 10 false A22 5.729,2.99 6.969,3.479 1.24,0.49 10 false ECM 5.865,2.521 6.781,2.719 0.917,0.198 10 false E1 5.865,2.135 6.781,2.333 0.917,0.198 10 false IGSW 5.865,3.677 6.781,3.875 0.917,0.198 10 false IG1D 5.615,2.417 5.917,2.646 0.302,0.229 10 false 10 5.667,2.031 5.969,2.26 0.302,0.229 10 false 2 5.625,3.583 5.927,3.813 0.302,0.229 10 false 17 5.292,1.396 7.01,1.906 1.719,0.51 10 false Hybrid Vehicle Control ECU Assembly 5.854,1 6.771,1.198 0.917,0.198 10 false E01 5.854,0.448 6.771,0.646 0.917,0.198 10 false IG2 5.51,0.979 5.813,1.208 0.302,0.229 10 false K69 5.594,0.781 5.896,1.01 0.302,0.229 10 false 5 5.51,0.552 5.813,0.781 0.302,0.229 10 false A28 5.583,0.365 5.885,0.594 0.302,0.229 10 false 3 3.5,0.448 3.802,0.677 0.302,0.229 10 false 1 1.792,0.438 2.094,0.667 0.302,0.229 10 false 2 3.948,0.438 4.25,0.667 0.302,0.229 10 false 2 1.375,0.448 1.677,0.677 0.302,0.229 10 false 1 2.375,0.458 2.677,0.688 0.302,0.229 10 false 5 2.365,0.875 2.667,1.104 0.302,0.229 10 false 2 3.146,0.448 3.448,0.677 0.302,0.229 10 false 3 3.135,0.875 3.438,1.104 0.302,0.229 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.CHECK AUXILIARY BATTERY VOLTAGE
a.

Turn the power switch off and turn on the high beam headlights for 30 seconds. This will remove the surface charge from the auxiliary battery.


b.

Measure the auxiliary battery voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal 20°C (68°F), Power switch off 11.0 V or higher


Result:
Proceed to
OK
NG




OK

3.CLEAR DTC

NG

2.CHARGE OR REPLACE AUXILIARY BATTERY
2.CHARGE OR REPLACE AUXILIARY BATTERY
a.

Charge or replace the auxiliary battery.


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs
50002 397

f.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Turn the power switch on (IG) and wait for 15 seconds or more.


b.

Turn the power switch off and wait for 2 minutes or more.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P253012 is output A
P253012 is not output B



g.

Turn the power switch off.



A

5.CHECK DTC OUTPUT (HYBRID CONTROL)

B

5.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
U012987, U014087, U015187, U016487, U110787 or U117087 is output A
Other than above B



e.

Turn the power switch off.



A

6.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY
a.
A389519C05
0.625,0.667 1.125,0.917 0.5,0.25 1.896,0.698 2.396,0.948 0.5,0.25 0.885,2.375 1.167,2.917 true 1.917,2.375 2.417,2.917 true 0.188,0.417 0.5,0.573 0.313,0.156 10 false *a 1.125,2.958 1.521,3.125 0.396,0.167 10 false IG2 2.365,2.948 2.76,3.115 0.396,0.167 10 false E01 0.75,0.708 1.052,0.906 0.302,0.198 10 false A28 2.031,0.74 2.406,0.917 0.375,0.177 10 false K69
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Disconnect the A28 and K69 hybrid vehicle control ECU assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Condition:
Tester Connection Condition
A28-3 (IG2) - K69-5 (E01) Power switch off



c.

Reconnect the A28 and K69 hybrid vehicle control ECU assembly connectors.


Result:
Result Proceed to
9 V or higher A
Below 9 V B



A

7.CHECK ECM

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

7.CHECK ECM
a.
A389519C05
0.625,0.667 1.125,0.917 0.5,0.25 1.896,0.698 2.396,0.948 0.5,0.25 0.885,2.375 1.167,2.917 true 1.917,2.375 2.417,2.917 true 0.188,0.417 0.5,0.573 0.313,0.156 10 false *a 1.125,2.958 1.521,3.125 0.396,0.167 10 false IG2 2.365,2.948 2.76,3.115 0.396,0.167 10 false E01 0.75,0.708 1.052,0.906 0.302,0.198 10 false A28 2.031,0.74 2.406,0.917 0.375,0.177 10 false K69
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Disconnect the A28 and K69 hybrid vehicle control ECU assembly connectors.


b.

Disconnect the A22 ECM connector.


c.

Measure the voltage according to the value(s) in the table below.

Condition:
Tester Connection Condition
A28-3 (IG2) - K69-5 (E01) Power switch off



d.

Reconnect the A22 ECM connector.


e.

Reconnect the A28 and K69 hybrid vehicle control ECU assembly connectors.


Result:
Result Proceed to
9 V or higher A
Below 9 V B



A

8.INSPECT RELAY (IG2 NO. 1)

B

8.INSPECT RELAY (IG2 NO. 1)
a.
A406712C03
2.177,1.479 2.531,1.688 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *1 2.604,1.708 2.917,1.865 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 IG2 NO. 1 Relay


Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.
B060778N68
2.51,1.625 2.844,1.625 true 2.521,1.125 2.854,1.125 true 2.615,0.583 2.792,0.271 2.792,0.271 2.948,0.271 true 2.021,0.573 1.865,0.26 1.865,0.26 1.719,0.26 true 2.896,1.552 3.406,2.167 0.51,0.615 10 true 3 2.906,1.042 3.104,1.24 0.198,0.198 10 false 5 3.01,0.177 3.208,0.375 0.198,0.198 10 false 2 1.573,0.177 1.771,0.375 0.198,0.198 10 false 1 1.219,0.76 1.417,0.958 0.198,0.198 10 false 5 1.229,1.302 1.427,1.5 0.198,0.198 10 false 2 0.208,0.76 0.417,0.927 0.208,0.167 10 false 3 0.219,1.302 0.417,1.5 0.198,0.198 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the IG2 NO. 1 relay.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - IG2 NO. 1 RELAY)

NG

REPLACE RELAY (IG2 NO. 1)

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - IG2 NO. 1 RELAY)
a.

Disconnect the A28 hybrid vehicle control ECU assembly connector.


b.

Remove the IG2 NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.
A389501C17
0.656,0.667 1.156,0.917 0.5,0.25 1.25,2.75 0.875,2.375 true 0.188,0.573 0.5,0.729 0.313,0.156 10 false *a 1.208,2.781 1.688,2.938 0.479,0.156 10 false IG2 0.781,0.708 1.094,0.906 0.313,0.198 10 false A28
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-3 (IG2) - Body ground Power switch off 1 V or less



d.

Install the IG2 NO. 1 relay.


e.

Reconnect the A28 hybrid vehicle control ECU assembly connector.


Result:
Proceed to
OK
NG



OK

CHECK FOR INTERMITTENT PROBLEMS
a.

Check for intermittent problems.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>CHECK FOR INTERMITTENT PROBLEMS

i.

Check the connection and terminal contact pressure of the connectors and wire harnesses between the hybrid vehicle control ECU assembly and the IG2 No. 1 relay.


ii.

When the power switch is on (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU assembly and the IG2 No. 1 relay.




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR